Manuale d’uso / di manutenzione del prodotto WESY59100 del fabbricante Weider
Vai alla pagina of 32
USER'S MANUAL QUESTIONS? As a manufacturer , we are committed to providing complete customer satisfaction. If you have questions, or if there are missing parts, we will guarantee complete satisfaction through assistance from our factory . TO A VOID DELA YS, PLEASE CALL DIRECT T O OUR TOLL-FREE CUST OMER HOT LINE.
2 T ABLE OF CONTENTS LIMITED W ARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 IMPORT ANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IMPORT ANT PRECAUTIONS 3 1. It is the responsibility of the owner to ensure that all users of the training system are ade- quately informed of all precautions. 2. Read all instructions in this manual and in the accompanying literature before using the training system.
4 BEFORE YOU BEGIN ASSEMBLED DIMENSIONS: Height: 76.0 in. Width: 86.5 in. Length: 91.5 in. Foot Plate Low Pulley Station High Pulley Station Lat Bar Leg Lever Butterfly Arms Press Arms Leg Press Seat .
5 ASSEMBL Y Make sure you have the following tools: • T wo (2) adjustable wrenches • One (1) standard screwdriver • One (1) phillips screwdriver • One (1) rubber mallet • Y ou will also need grease or petroleum jelly , a small amount of soapy water , and clear tape or masking tape.
1. Locate and open the parts bags labeled “FRAME ASSEMBL Y .” See the inset drawing. Insert two 1 1/2” x 2 1/2” Inner Caps (83) and two 3/8” x 2” Carriage Bolts (92) into the Butterfly Base (4). Insert two 1 1/2” x 2 1/2” Inner Caps (83) into the indicated ends of the Butterfly Base (4) and the Press Base (6).
5. Attach the Butterfly Seat Frame (14) to the Butterfly Upright (1) with two 3/8” x 3 1/4” Bolts (62), two 3/8” Flat W ashers (48), and two 3/8” Nylon Locknuts (50). Attach the Butterfly Seat Frame (14) to the Butterfly Front Leg (3) with two 3/8” x 3 1/4” Bolts (62), two 3/8” Flat W ashers (48) and two 3/8” Nylon Locknuts (50).
8 89 48 48 48 89 51 6 50 48 21 Slot 15 9. See the inset drawing. Insert two Weight Inserts (56) into each Weight (21). Set the two Weight Bumpers (51) over the holes in the corner bar of the Press Base (6). Slide the Weight Guides (15) through the W eight Bumpers (51) and the holes in the Press Base (6).
9 48 62 50 48 33 9 12. Secure the Press T op Frame (9) to the Butterfly T op Frame (33) with two 3/8” x 3 1/4” Bolts (62), two 3/8” Flat W ashers (48), and two 3/8” Nylon Locknuts (50).
10 15 48 48 10 84 28 10 28 48 48 53 53 15. Insert a 2” Square Inner Cap (28) into the end of the Butterfly Arm (10). Attach a Butterfly Handle (53) to the Butterfly Arm (10) with two 3/8” x 1” Bolts (84) and two 3/8” Flat W ashers (48). Repeat this step with the other Butterfly Arm (10).
21. Locate and open the parts bags labeled “CABLE ASSEMBL Y” and “PULLEYS.” Secure a 3/8” x 2 1/4” Bolt (79) to the Right Pivot Arm (85) with a 3/8” Nylon Jamnut (63). Locate the Butterfly Cable (73), which is the shorter cable of the two that have loops on both ends.
12 23. Remove the preassembled 3/8” x 2” Bolts (54) from one set of Adjustable Pulley Plates (23). Wrap the Butterfly Cable (73) around a 3 1/2” Pulley (24). Attach the 3 1/2” Pulley and a Cable T rap (25) between the top holes of the Adjustable Pulley Plates (23) with a 3/8” x 2” Bolt (54) and a 3/8” Nylon Locknut (50).
13 27. Wrap the Ab Cable (47) around a 3 1/2” Pulley (24). Insert the Ab Cable down through the Press T op Frame (9). Attach a 3/8” Flat W asher (48) and a 5/8” x 3/4” Bushing (66) to a 3/8” x 3 1/4” Bolt (62). Slide the Bolt through the Press T op Frame and the 3 1/2” Pulley .
14 31. Locate the Weight Cable (72). Note that one end of the Weight Cable has a bolt, and the other end has a ball on it. Lay the Weight Cable (72) inside the bracket on the Butterfly Base (4) in the manner shown. Attach a 3 1/2” Pulley (24) to the bracket with a 3/8” x 2” Bolt (54) and a 3/8” Nylon Locknut (50).
15 36 37 38 35. Wrap the Weight Cable (72) around a 3 1/2” Pulley (24). Attach the 3 1/2” Pulley and a Cable T rap (25) to the Butterfly Upright (1) with a 3/8” x 4” Bolt (59), a 3/8” Flat W asher (48), and a 3/8” Nylon Jamnut (63). Be sure that the Cable T rap is turned to hold the Cable in place.
16 39. Wrap the Weight Cable (72) around a 3 1/2” Pulley (24). Attach the 3 1/2” Pulley and a Cable T rap (25) between the lowest holes in the Adjustable Pulley Plates (23) hanging from the Ab Cable (47) with a 3/8” x 2” Bolt (54) and a 3/8” Nylon Locknut (50) that was removed in step 28.
17 43. Locate the Leg Press Cable (75). Attach the Leg Press Cable to the indicated side of the Press Upright (2) with a 3/8” x 3 1/4” Bolt (62) and a 3/8” Nylon Locknut (50). Do not tighten the Nylon Locknut yet. Wrap the Leg Press Cable (75) up around a 3 1/2” Pulley (24) in the direction shown.
18 47. Remove the 3/8” Nylon Locknut (50) from the indi- cated 3/8” x 5 1/2” Bolt (55). Wrap the Leg Press Cable (75) around a 3 1/2” Pulley (24). Secure the 3 1/2” Pulley and a Cable T rap (25) to the 3/8” x 5 1/2” Bolt (55) on the indi- cated side of the Press Base (6) with the 3/8” Nylon Locknut (50).
19 51. Locate and open the parts bag labeled “SEA T ASSEMBL Y .” Attach a Seat (13) to the brackets on the Butterfly Seat Frame (14) using four 1/4” x 3/4” Bolts (49). Repeat this step with the other Seat (not shown) and the Press Seat Frame (not shown).
Before using the training system, pull each cable a few times to be sure that the cables move smoothly over the pulleys. If one of the cables does not move smoothly , find and correct the problem. IMPORT ANT : If the cables are not properly installed, they may be damaged when heavy weight is used.
21 HOW T O USE THE TRAINING SYSTEM The instructions below describe how each part of the training system can be adjusted. Refer to the exercise guide accompanying this manual to see how the training system should be set up for each exercise.
22 A TT ACHING THE AB STRAP TO THE AB PULLEY ST A TION Attach the Ab Strap (81) to the Ab Cable (47) at the ab pulley station with a Cable Clip (69). ADJUSTING THE BACKREST T o adjust a Backrest (12),.
23 WEIGHT RESIST ANCE CHART This chart shows the approximate weight resistance at each weight station. “T op” refers to the 10 lb. top weight. The other numbers refer to the 10 lb. weight plates. The butterfly arm resistance listed is the resistance for each butterfly arm.
TROUBLE-SHOOTING AND MAINTENANCE Inspect and tighten all parts each time you use the training system. Replace any worn parts immediately . The training system can be cleaned using a damp cloth and mild non-abrasive detergent.
25 CABLE DIAGRAMS The cable diagrams on this page and the next page show the proper routing of the Leg Press Cable (75), the Ab Cable (47), the Butterfly Cable (73), and the Weight Cable (72). Use the diagrams to be sure that the Cables have been assembled correctly .
26 Weight Cable (72) 2 3 1—Low Pulley 4 8 11 12—Weight Stack 7 6 5 Cable ID 72 47 75 73 9 10.
3/4" Round Inner Cap (43) Cable Clip (69) "V" Pulley (27) (Not shown to scale) 3 1/2" Pulley (24) (Not shown to scale) Retainer Ring (31) 4 1/2" Pulley (82) (Not shown to scal.
3/8" x 1" Bolt (84) 3/8" x 1 3/4" Bolt (57) 3/8" x 1 1/4" Button Head Bolt (98) 1/4" x 3/4" Bolt (49) 3/8" x 2 1/4" Bolt (79) 3/8" x 4" Bolt.
2" x 3” Inner Cap (78) 2" Square Inner Cap (28) 1 1/2" Square Inner Cap (35) 1 1/2" x 2 1/2” Inner Cap (83) 2 1/2" Square Inner Cap (76).
P ART LIST—Model No. WESY59100 R1200A Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. Key No. Qty .
92 92 49 39 49 23 25 24 25 24 23 50 54 23 25 24 25 24 23 50 44 35 49 86 65 77 28 65 86 77 64 25 24 60 96 68 36 25 24 50 8 68 29 36 68 36 63 25 24 25 24 60 90 78 62 48 50 80 40 20 50 83 6 60 24 25 50 5.
ORDERING REPLACEMENT P ARTS T o order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, Monday through Friday , 6 a.m. until 6 p.m. Mountain T ime (excluding holidays). T o help us assist you, please be pre- pared to give the following information: 1.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Weider WESY59100 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Weider WESY59100 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Weider WESY59100 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Weider WESY59100 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Weider WESY59100, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Weider WESY59100.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Weider WESY59100. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Weider WESY59100 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
