Manuale d’uso / di manutenzione del prodotto WESY39523 del fabbricante Weider
Vai alla pagina of 35
USER'S MANUAL QUESTIONS? As a manufacturer , we are committed to providing complete customer satisfaction. If you have questions, or if parts are missing, we will guarantee com- plete satisfaction through assis- tance from our factory . TO A VOID DELA YS, PLEASE CALL DIRECT TO OUR TOLL- FREE CUSTOMER HOT LINE.
2 T ABLE OF CONTENTS IMPORT ANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IMPORT ANT PRECAUTIONS 3 1. Read all instructions in this manual and in the accompanying literature before using the weight system. 2. It is the responsibility of the owner to ensure that all users of the weight system are ade- quately informed of all precautions.
4 BEFORE YOU BEGIN ASSEMBLED DIMENSIONS: Height: 81 in. Width: 96 in. Length: 57 in. Squat Knee Rest Low Pulley Station High Pulley Station Lat Bar Swivel Carriage Adjustment Knob Adjustment Handle Bu.
5 ASSEMBL Y Make sure that you have the following tools: • T wo adjustable wrenches • One standard screwdriver • One phillips screwdriver • One rubber mallet • Y ou will also need grease or petroleum jelly , a small amount of soapy water , and masking tape.
1. Locate and open the parts bags labeled “FRAME ASSEMBL Y 1” and “FRAME ASSEMBL Y 2.” See the inset drawing. Attach the Base Cap (24) to the Short Base (2) with two M4 x 20mm Self-tap- ping Screws (14) and two M4 W ashers (120). Press a 50mm Square Inner Cap (105) into the open end of the Long Base (101).
4. Press a 38mm Square Inner Cap (67) into the Upright Extension (12). Attach the Upright Extension (12) to the Butterfly Upright (3) with two M10 x 95mm Bolts (92), two M10 W ashers (91), and two M10 Nylon Locknuts (87). Make sure the warning decals on each side of the Extension are right-side up.
8 7. Press a 50mm x 75mm Inner Cap (58) into the top of the Squat Upright (4). Press two 25mm Round Outer Cap (121) onto the Upright. Slide the Squat Upright onto the two indicated M10 x 65mm Carriage Bolts (1 10) in the Long Base (101). Finger tighten an M10 Nylon Locknut (87) onto each Carriage Bolt.
9 9. Attach a Roller (39) between the indicated set of holes in the Squat Slider (38) with an M8 x 85mm Bolt (94) and an M8 Nylon Locknut (34). Do not overtighten the Locknut; the Roller must be able to roll easily . Assemble the other three Rollers (39) to the Squat Slider (38) in the same manner .
10 14. Open the parts bag labeled “ARM ASSEMBL Y .” Press three 40mm x 50mm Inner Caps (21) into the Leg Lever (10). Lubricate an M10 x 65mm Bolt (18) with grease. T urn the Leg Lever (10) so that the welded tab is on the indicated side, and attach the Leg Lever to the Seat Upright (9) with the Bolt and an M10 Nylon Locknut (87).
18. Locate and open the parts bags labeled “CABLE ASSEMBL Y” and “PULLEYS.” Lubricate the M10 x 165mm Bolt (30) with grease. Attach the Swivel Cage (76) to the Swivel Carriage (46) with the Bolt and an M10 Nylon Locknut (87).
12 20. Remove the preattached 90mm Pulleys (78) from the Small Pulley Plates (31). Wrap the Swivel High Cable (74) over a 90mm Pulley (78). Attach the Pulley and a Cable T rap (68) to the second set of holes from the top of the Small Pulley Plates (31) with an M10 x 50mm Bolt (100) and an M10 Nylon Locknut (87).
13 24. Remove the preattached 90mm Pulleys (78) from the Offset Double “U”-bracket (61). Wrap the Swivel Cable (17) around a 90mm Pulley (78). Attach the Pulley to the Offset Double “U”- bracket (61) with an M10 x 45mm Bolt (93) and an M10 Nylon Locknut (87).
14 29. Wrap the Lat Cable (88) around a 90mm Pulley (78). Attach the Pulley and a Long Cable T rap (102) to the T op Frame (6) with an M10 x 50mm Bolt (100) and an M10 Nylon Locknut (87). Make sure the Cable T rap is turned to hold the Cable in the groove of the Pulley .
15 35 36 38 37 34. Remove the preattached 90mm Pulleys (78) from the Double “U”-bracket (62). Wrap the Butterfly Cable (69) under a 90mm Pulley (78). Attach the Pulley to the Double “U”-bracket (62) with an M10 x 45mm Bolt (93) and an M10 Nylon Locknut (87).
16 41. Remove the preattached 90mm Pulley (not shown) from the “U”-bracket (64). Attach the end of the Leg Lever Cable (75) to the “U”-bracket (64) with an M8 W asher (90) and an M8 Nylon Locknut (34). Note: Do not completely tighten the Locknut; it should be threaded only two turns onto the end of the Cable, as shown in the inset drawing.
17 45. Wrap the Swivel Low Cable (72) under a 90mm Pulley (78). Attach the Pulley to the indicated brack- et on the Long Base (101) with an M10 x 45mm Bolt (93) and an M10 Nylon Locknut (87). 46. Route the Swivel Low Cable (72) under the indicat- ed stack of Weights (44).
18 49. Wrap the Swivel Low Cable (72) over a 90mm Pulley (78). Attach the Pulley and a Cable T rap (68) between the lower set of holes in the “U”-bracket (64) with an M10 x 50mm Bolt (100) and an M10 Nylon Locknut (87). Make sure that the Cable T rap is turned to hold the Cable in the groove of the Pulley .
19 53. Wrap the Squat Cable (73) under a 90mm Pulley (78). Attach the Pulley and a Cable T rap (68) to the second set of holes from the top in the indicated bracket on the Long Base (101) with an M10 x 50mm Bolt (100) and an M10 Nylon Locknut (87). Make sure that the Cable T rap is turned to hold the Cable in the groove of the Pulley .
20 57. Press two 20mm x 40mm Inner Caps (1 16) and a 25mm x 40mm Square Inner Cap (1 17) into the Seat Bracket (1 1). Attach the Seat (16) to the Seat Bracket (1 1) with two M6 x 16mm Screws (1 14), an M6 x 35mm Screw (99), and an M6 W asher (97). T urn the indicated Adjustment Handle (65) counter- clockwise several turns to loosen it.
21 61 61. T urn the Squat Backrest (35) so that the four screw holes are closer to the bottom of the Squat Backrest than the top. Attach the Squat Backrest to the Squat Bracket (37) with four M6 x 16mm Screws (1 14). Fully tighten the Adjustment Knob (1 15) into the Squat Bracket (37).
22 ADJUSTMENTS The instructions below describe how each part of the weight system can be adjusted. Refer to the exercise guide accompanying this manual to see how the weight system should be set up for various exercises.
23 ADJUSTING THE SQUA T ARM, SEA T , OR BUTTERFL Y BACKREST T o adjust the height of the Squat Arm (32), first turn the Adjustment Knob (1 15) on the Squat Bracket (37) counterclockwise several turns to loosen it. Next, pull the Handle and slide the Squat Bracket up or down to the desired position.
HIGH PULLEY (lbs.) 14 25 38 48 61 68 80 96 101 11 2 122 LOW PULLEY (lbs.) 14 25 36 44 60 70 80 91 104 111 122 LEG LEVER (lbs.) 22 35 53 67 91 111 122 148 160 184 190 BUTTERFL Y ARM (lbs.) 17 26 36 45 54 63 71 80 91 100 108 PRESS ARM (lbs.) 24 39 55 70 89 104 11 8 136 154 167 187 SQUA T ST A TION (lbs.
25 TROUBLESHOOTING Make sure all parts are properly tightened each time the weight system is used. Replace any worn parts immedi- ately . The weight system can be cleaned using a damp cloth and mild non-abrasive detergent.
26 CABLE DIAGRAMS The cable identification chart below shows the ends of each cable and the lengths of the cables. The cable dia- grams on this page and the following page show the proper routing of the cables. The numbers in the diagrams show the routes of the cables.
27 Leg Lever Cable (75) Swivel Low Cable (72) 1 1 3 2 4 5 6 7 9 2 3 4 1 2 3 4 5 8 Swivel Cable (17).
ORDERING REPLACEMENT P ARTS T o order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, Monday through Friday , 6 a.
Note: Assembly is divided into four stages: 1) frame assembly , 2) arm assembly , 3) cable assembly , and 4) seat assembly . The hardware for each stage is packaged in separate bags. W AIT UNTIL YOU BEGIN EACH ASSEMBL Y ST AGE TO OPEN THE P ARTS BAG LABELED FOR THA T ASSEMBL Y ST AGE.
Cable Clip (83) 90mm Pulley (78) (Not shown to scale) "V"-pulley (55) (Not shown to scale) 1 15mm Pulley (1 19) (Not shown to scale) M10 Nylon Locknut (87) M8 Nylon Locknut (34) M8 W asher (.
M10 x 20mm Bolt (86) M10 x 60mm Bolt (59) M10 x 70mm Bolt (85) M10 x 95mm Bolt (92) M10 x 45mm Bolt (93) M10 x 85mm Bolt (96) M10 x 165mm Bolt (30) M10 x 50mm Bolt (100) M10 x 80mm Button Head Bolt (1.
50mm x 75mm Inner Cap (58) 40mm x 50mm Inner Cap (21) 25mm Round Inner Cap (29) 50mm x 70mm Inner Cap (95) 38mm Square Inner Cap (67) 50mm Square Inner Cap (105) 25mm x 40mm Inner Cap (1 17) 20mm x 40.
8 1 REMOVE THIS P ART LIST/EXPLODED DRA WING FROM THE MANUAL. SA VE THIS P ART LIST/EXPLODED DRA WING FOR FUTURE REFERENCE.
P ART LIST—Model No. WESY39523 R0103A Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. 1 2 50mm W asher 2 1 Short Base 3 1 Butterfly Upright 4 1 S.
4 6 5 7 3 2 8 9 10 11 13 15 16 109 109 19 19 20 20 21 21 20 21 23 24 25 26 27 27 28 29 29 28 32 33 33 111 111 35 37 38 39 39 40 40 40 42 42 43 43 47 45 44 45 44 48 48 49 50 50 11 4 11 4 11 4 11 4 52 5.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Weider WESY39523 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Weider WESY39523 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Weider WESY39523 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Weider WESY39523 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Weider WESY39523, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Weider WESY39523.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Weider WESY39523. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Weider WESY39523 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
