Manuale d’uso / di manutenzione del prodotto WESY19510 del fabbricante Weider
Vai alla pagina of 28
USER'S MANUAL QUESTIONS? As a manufacturer , we are com- mitted to providing complete customer satisfaction. If you have questions, or find there are miss- ing or damaged parts, we will guarantee you complete satisfac- tion through direct assistance from our factory .
2 T ABLE OF CONTENTS IMPORT ANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3 W ARNING : T o reduce the risk of serious injury , read the following important precautions before using the weight system. IMPORT ANT PRECAUTIONS W ARNING: Before beginning this or any exercise program, consult your physician. This is especially important for persons over the age of 35 or persons with pre-existing health problems.
4 BEFORE YOU BEGIN ASSEMBLED DIMENSIONS: Height: 76 in. Width: 37 in. Length: 48 in. Foot Plate Low Pulley Station High Pulley Station Left Side Right Side Lat Bar Decal 1 Decal 2 Leg Lever Butterfly Arms Press Arm Preacher Pad Weight Stack Seat Backrest Weight Pin Thank you for selecting the versatile WEIDER ® 8525 weight system.
5 1 56 High Side of Bracket 3 5 51 51 14 1 27 4 1. Before beginning assembly , be sure that you have read and understand the information in the box above. Press a 2” Square Outer Cap (51) onto each end of the Stabilizer (5). Press a 2” Square Inner Cap (27) into the end of the Base (4).
6 2. Slide the Front Upright (42) onto the 5/16” x 2 1/2” Carriage Bolts (1) in the Base (4). Hand tighten a 5/16” Nylon Locknut (3) onto each Carriage Bolt. Do not tighten the Nylon Locknuts yet. Press a 1” Square Inner Cap (65) into the Front Upright (42).
7 5. Press the Weight T ube Bumper (64) into the end of the Weight T ube (63). Insert the Weight T ube into the stack of Weights (25). Be sure that the pins on the Weight T ube are resting in the pin grooves in the upper Weight. Lubricate the insides of the holes in the T op Weight (76).
8 8. Press a 1 3/4” Square Inner Cap (44) into the top of a Press Arm (46). Press a 1” Round Inner Cap (49) into each end of the handle on the Press Arm. Attach the Press Arm (46) to one side of the Press Frame (17) with two 5/16” x 2 1/2” Bolts (22) and two 5/16” Nylon Locknuts (3).
9 1 1. During steps 1 1 through 24, refer to the CABLE DIAGRAM on page 20 of this manual to verify proper cable routing. Before beginning this sec- tion, identify the Long Cable (23) and the Short Cable (58) by comparing the lengths of the cables. IMPORT ANT : While assembling the cables, do not overtighten the bolts and nuts securing the pulleys.
10 15. Route the Long Cable (23) around the “V”-Pulley (6) on the Right Arm (48). Be sure that the Cable is in the groove of the “V”-Pulley and that the Long Cable T rap (50) is turned to hold the Cable in place. T ighten the 3/8” x 2 1/2” Bolt (7) and the 3/8” Nylon Locknut (not shown).
11 19. Locate the Short Cable (58). Lay the Short Cable in the bracket on the Base (4). Attach the 3 1/2” Pulley (15) to the bracket with a 3/8” x 2” Bolt (12) and a 3/8” Nylon Locknut (21). Be sure that the end of the Cable with the ball is on the indicated side of the bracket.
12 22. Route the Short Cable (58) around the 3 1/2” Pulley (15) attached to the upper hole in the Front Upright (42). See the inset drawing. Be sure that the Cable T rap (66) is turned to hold the Cable in place and that the Cable is routed around the Pulley as shown.
24. Attach the Long Cable (23) to the Small “U”- Bracket (67) with a 1/4” Nylon Locknut (2) and a 1/4” Flat W asher (10). See the inset drawing. Do not overtighten the Nylon Locknut; it should be threaded onto the end of the Cable only a couple of turns, as shown.
14 26. Press a 1 1/2” Square Inner Cap (32) into the Seat Frame (36). Insert the 1/4” x 2” Carriage Bolt (38) into the center hole in the Seat Plate (37). Attach the Seat Plate to the Seat (13) with two 1/4” x 3/4” Screws (18). Insert the 1/4” x 2” Carriage Bolt (38) into the indi- cated hole in the Seat Frame (36).
15 29. Press a 3/4” Round Inner Cap (34) into each end of both 12 1/2” Pad T ubes (28). Insert one 12 1/2” Pad T ube (28) into the Seat Frame (36). Slide a 5 1/2” Pad (30) onto each end of the Pad T ube. Insert the other 12 1/2” Pad T ube (28) into the Leg Lever (29).
16 ADJUSTMENTS The instructions below describe how each part of the weight system can be adjusted. Refer to the exercise guide accompanying this manual to see how the weight system should be set up for each exercise.
17 A TT ACHING THE LEG LEVER TO THE LOW PULLEY ST A TION T o use the Leg Lever (29), the seat must be attached to the front upright (see A TT ACHING AND REMOV- ING THE SEA T , on page 16). Attach the Short Cable (58) to the indicated 3/8” x 2” Eyebolt (35) with a Cable Clip (53).
18 WEIGHT PRESS ARM BUTTERFL Y ARM LEG LEVER HIGH PULLEY LOW PULLEY PLA TES (lbs.) (lbs.) (lbs.) (lbs.) (lbs.) To p 2 0 1 0 1 5 1 4 2 4 14 5 2 2 3 6 2 8 5 4 27 0 3 3 5 4 4 4 8 2 39 9 4 2 7 5 6 0 1 1 5 4 128 48 96 72 147 5 153 60 1 15 90 175 6 184 69 137 103 209 This chart shows the approximate weight resistance at each station.
19 TROUBLE-SHOOTING AND MAINTENANCE Inspect and tighten all parts each time you use the weight system. Replace any worn parts immediately . The weight system can be cleaned using a damp cloth and mild non-abrasive detergent.
20 CABLE DIAGRAM The cable diagram below shows the proper routing of the Short Cable (58) and the Long Cable (23). Use the diagram to be sure that the two cables and the cable traps have been assembled correctly . If the cables have not been correctly routed, the weight system will not function properly and damage may occur .
21 NOTES.
22 Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. P ART LIST—Model No. WESY19510 R1 101A 1 2 5/16” x 2 1/2” Carriage Bolt 2 3 1/4” Nylon L.
23 11 11 8 8 55 27 12 15 44 15 71 23 27 21 44 21 3 61 60 3 56 15 12 2 57 58 21 3 5 51 14 19 26 51 25 64 63 76 9 21 3 3 4 1 27 65 15 71 41 10 43 3 21 6 50 7 42 7 50 6 21 69 70 69 70 47 48 44 45 44 45 1.
ORDERING REPLACEMENT P ARTS T o order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, Monday through Friday , 6 a.m. until 6 p.m. Mountain T ime (excluding holidays). T o help us assist you, please be pre- pared to give the following information: 1.
This chart is provided to help you identify the small parts used in assembly . Important: S ome parts may have been p re-assembled for shipping purposes; if you cannot find a part in the parts bags, check to see if it has been p re-assembled.
5/16" Nylon Locknut (3) 1/4" Flat W asher (10) 5/16" Flat W asher (8) 3/8" Flat W asher (9) 1/4" x 2 1/2" Screw (43) 5/16" x 1 3/4" Bolt (72) 3/8" Nylon Lo.
1" Retainer (69) 3/8" x 2" Bolt (12) 3/8" x 3 1/2" Bolt (16) 3/8" x 2 1/2" Bolt (7) 3/8" x 3 3/4" Bolt (71) 3/8" x 8" Bolt (59) Cable Clip (53) 5.
1" Round Inner Cap (49) 1" Round Cover Cap (70) 1/2" x 3/4" Spacer (61) Round Inner Cap (77) 1 1/2" Square Inner Cap (32) 1 3/4" Square Inner Cap (44) 2" Square Inne.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Weider WESY19510 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Weider WESY19510 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Weider WESY19510 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Weider WESY19510 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Weider WESY19510, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Weider WESY19510.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Weider WESY19510. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Weider WESY19510 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
