Manuale d’uso / di manutenzione del prodotto WESY19002 del fabbricante Weider
Vai alla pagina of 24
USER'S MANUAL QUESTIONS? As a manufacturer , we are committed to providing complete customer satisfaction. If you have questions, or if there are missing parts, we will guarantee complete satisfaction through direct assistance from our factory . TO A VOID UNNECESSAR Y DELA YS, PLEASE CALL DIRECT TO OUR TOLL-FREE CUST OMER HOT LINE.
2 T ABLE OF CONTENTS IMPORT ANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3 1. Read all instructions in this manual and in the accompanying literature before using the training system. Use the training system only as described in the literature. 2. It is the responsibility of the owner to ensure that all users of the training system are ade- quately informed of all precautions.
4 BEFORE YOU BEGIN Foot Plate Low Pulley Station High Pulley Station Lat Bar Leg Lever Butterfly Arm Curl Pad Curl Frame Press Arm We ight Stack Backrest Shroud Seat Thank you for selecting the versatile WEIDER ® 245 training system. The WEIDER ® 245 of fers a selection of weight stations designed to develop every major muscle group of the body .
1/4" Nylon Lockn ut (2) 1/2" x 1/2" Spacer (61) 5/16" Nylon Jamnut (87) 1/4" W asher (78) 5/16" SAE W asher (88) 5/8" x 1/2" Spacer (82) 3/8" Nylon Jamnut .
5/16" x 2 3/4" Shoulder Bolt (85) 1/4" x 2 1/4" Carriage Bolt (38) 5/16" x 6" Bolt (60) 3/8" x 5" Bolt (75) 3/8" x 4 1/4" Bolt (64) 3/8" x 4".
7 ASSEMBL Y Make sure you have the following tools: • T wo (2) adjustable wrenches • One (1) standard screwdriver • One (1) phillips screwdriver • One (1) rubber mallet •Y ou will also need grease or petroleum jelly , a small amount of soapy water , and clear tape or masking tape.
3 4 FRAME ASSEMBL Y 8 1 21 42 4 19 25 Pin Groove 62 3. Attach the Front Upright (42) to the Base (4) using two 3/8” x 2 1/4” Bolts (1) and two 3/8” Nylon Locknuts (21). Do not tighten the Nylon Locknuts yet. 4. Slide a Weight Bumper (19) down over each W eight Guide (62).
5. Insert the Weight Tube Cap (72) into the indi- cated end of the Weight Tube (63). Slide the W eight Tube into the center holes in the We ights (25). Slide the T op Weight (56) down onto the Weight Guides (62) as shown. 6. Press four 1 1/2” x 2 1/2” Inner Caps (27) into the T op Frame (55).
ARM ASSEMBL Y FRAME ASSEMBL Y 8. Attach the T op Frame (55) to the Weight Guides (62) using a 5/16” x 6” Bolt (60), two 1/2” x 1/2” Spacers (61), and a 5/16” Nylon Locknut (3) as shown. T ighten all Nylon Locknuts used in steps 3 through 8. 9.
11 ARM ASSEMBL Y 11 . Attach the Seat Plate (37) to the Seat Frame (36) using a 1/4” x 2 1/4” Carriage Bolt (38), a 1/4” Flat W asher (78), and a 1/4” Nylon Locknut (2). 12. Attach a Bumper (1 1) to the Seat Frame (36) using a #10 x 1” Screw (80).
18 15 48 47 Bracket Lubricate Axle 55 65 68 45 44 47 16 17 CABLE ASSEMBL Y ARM ASSEMBL Y 12 15. Press a 1 3/4” Square Inner Cap (44) into the lower end of the Left Arm (47). Using a small amount of soapy water , slide a Large Foam Pad (45) onto the Left Arm.
19. Route the Short Cable (23) around two “V”- Pulleys (6). Attach the Pulleys and two Long Cable T raps (50) to the Left Arm (47) and the Right Arm (48) as shown, using two 3/8” x 2 1/2” Bolts (7) and two 3/8” Nylon Locknuts (21). Do not overtighten the Nylon Locknuts; the Pulleys must be able to turn freely .
26 23 24 25 23. Locate the Long Cable (69). Route the Long Cable between the Base (4) and the Press Frame (17) as shown. Lay the Long Cable in the bracket on the Base. Attach the Pro-Pulley (77) to the bracket using a 3/8” x 2” Bolt (12) and a 3/8” Nylon Locknut (21).
27. Route the Long Cable (69) behind the Press Frame (17) and under the Seat Frame (36) as shown. Route the Long Cable around two 3 1/2” Pulleys (15). Slide the 3/8” x 5” Bolt (75) through the 3 1/2” Pulleys (15), two Cable T raps (66), and the Press Frame (17) as shown.
31. Attach the Seat (13) to the Seat Frame (36) using two 1/4” x 3/4” Bolts (18), a 1/4” x 2 1/4” Bolt (33), and a 1/4” W asher (78). 32. Attach the Backrest (41) to the Front Upright (42) using two 1/4” x 3” Bolts (43) and two 1/4” W ashers (78).
35. Attach the Shroud (59) to the brackets on the T op Frame (55) and the Base (4) using four #8 x 1/2” Screws (79). 17 35 79 79 59 55 79 4 SEA T ASSEMBL Y 36. Make sure that all parts have been properly tightened. The use of the remaining parts will be explained in ADJUSTMENT , beginning on page 18 of this manual.
18 54 39 53 53 52 23 25 26 CHANGING THE WEIGHT SETTING To change the weight setting of the weight stack, insert the Weight Pin (26) under the desired W eight (25). Be sure to insert the Weight Pin until the bent end of the Weight Pin is touching the W eights, and turn the bent end downward.
19 This chart shows the approximate weight resistance at each exercise station. “T op” refers to the 6.5 lb. top weight. The other numbers refer to the 10 lb. weight plates. The butterfly arm resistance listed is the resistance for each butterfly arm.
20 TROUBLE-SHOOTING AND MAINTENANCE Make sure all parts are properly tightened each time you use the training system. Replace any worn parts immedi- ately . The training system can be cleaned using a damp cloth and mild non-abrasive detergent. Do not use solvents.
21 CABLE DIAGRAM The diagram below shows the proper routing of the Short Cable (23) and the Long Cable (69). Use the diagram to be sure that the cables and the cable traps have been assembled correctly . If the cables have not been cor- rectly routed, the training system will not function properly and damage may occur .
Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. P ART LIST—Model No. WESY19002 R0303A Key No. Qty .
2 21 66 15 64 9 21 21 8 43 21 68 65 48 42 45 44 79 79 79 79 3 61 62 60 23 86 57 56 63 26 25 73 14 73 5 21 58 15 15 12 58 1 4 3 3 21 21 21 19 19 77 12 27 53 21 21 15 17 16 52 39 22 3 15 75 46 46 31 49 .
ORDERING REPLACEMENT P ARTS To order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, Monday through Friday , 6 a.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Weider WESY19002 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Weider WESY19002 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Weider WESY19002 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Weider WESY19002 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Weider WESY19002, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Weider WESY19002.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Weider WESY19002. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Weider WESY19002 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
