Manuale d’uso / di manutenzione del prodotto WESY13820 del fabbricante Weider
Vai alla pagina of 24
USER'S MANUAL CAUTION Read all precautions and instruc- tions in this manual before using this equipment. Save this manual for future reference. Model No. WESY13820 Model Number Decal (under seat) QUESTIONS? As a manufacturer , we are com- mitted to providing complete customer satisfaction.
2 WEIDER is a registered trademark of ICON Health & Fitness, Inc. IMPORT ANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 BEFORE YOU BEGIN . . . . . . . . .
3 1. Read all instructions in this manual and in the accompanying literature before using the weight system. Use the weight system only as described in this manual. 2. It is the responsibility of the owner to ensure that all users of the weight system are ade- quately informed of all precautions.
4 BEFORE YOU BEGIN Thank you for selecting the versatile WEIDER ® 950 weight system. The WEIDER ® 950 weight system offers a selection of weight stations designed to devel- op every major muscle group of the body .
5 Before beginning assembly , carefully read the following information and instructions: • Assembly requires two people. • Place all parts in a cleared area and remove the packing materials. Do not dispose of the packing materials until assembly is completed.
6 2. Press a 50mm Square Inner Cap (44) into the top of the Rear Upright (3). Attach the Rear Upright (3) to the Stabilizer (2) with the M8 x 67mm Carriage Bolts (66) and two M8 Nylon Locknuts (61). Attach the Front Upright (4) to the Base (1) with the two M8 x 63mm Carriage Bolts (65) and two M8 Nylon Locknuts (61).
7 5. Press two 25mm x 50mm Inner Cap (42) into the top of the Press Frame (9). Press two 50mm Square Inner Caps (44) into the ends of the Press Frame. Orient the Press Frame (9) with the bracket on the side shown. Attach the Press Frame to the T op Frame (5) with an M10 x 125mm Bolt (54), two M10 W ashers (55), and an M10 Nylon Locknuts (56).
8 10. Route the High Cable (35) down through the T op Frame (5) and around a Pulley (39). Attach the Pulley and a Cable T rap (41) to the second set of holes from the top of the two Pulley Plates (14) with an M10 x 48mm Bolt (77) and an M10 Nylon Locknut (56).
9 14. Wrap the Arm Cable (36) around a “V”-Pulley (38). Attach the Pulley and a Long Cable T rap (40) to a Pulley Bracket (30) with an M10 x 55mm Bolt (69) and an M10 Nylon Locknut (56). Be sure the Cable T rap is turned to hold the Cable in the groove of the Pulley .
10 17. Slide the Arm Cable (36) onto the hook on the Left Arm (1 1). 18. Locate the Short Cable (80). Attach the Cable to the side of the Base (1) with an M10 x 70mm Bolt (82), an M10 W asher (55), and an M10 Nylon Locknut (56). 16. Wrap the Arm Cable (36) around a “V”-Pulley (38).
11 20. Attach the Short Cable (80) to the “U”-Bracket (81) with an M8 W asher (76) and an M8 Nylon Locknut (61). Note: Do not completely tighten the Locknut; it should be threaded only two turns onto the end of the Cable, as shown in the inset drawing.
12 24. Wrap the Low Cable (37) around a Pulley (39). Attach the Pulley inside the bracket on the Base (1) with an M10 x 45mm Bolt (68) and an M10 Nylon Locknut (56).
13 28. Insert an M6 x 50mm Carriage Bolt (62) into the center hole in the Seat Plate (24). Attach the Seat Plate to the Seat (17) with two M6 x 16mm Screws (59). Attach the Seat (17) to the Seat Frame (6) with the M6 x 50mm Carriage Bolt (62), an M6 x 50mm Screw (64), two M6 W asher (63), and an M6 Nylon Locknut (58).
34. Make sure that all parts have been properly tightened. The use of all remaining parts will be explained in ADJUSTMENTS, on the next page. Before using the weight system, pull each cable a few times to make sure that the cables move smoothly over the pulleys.
15 This section explains how to adjust the weight system. Refer to the accompanying exercise guide to see the cor- rect form for each exercise. Make sure all parts are properly tightened each time the weight system is used. Replace any worn parts immediate- ly .
16 28 29 CONVERTING THE ARMS To use the Arms (10, 1 1) as butterfly arms, remove the Arm Pins (28) and engage the Arm Latch (29) into the hole in the Press Frame (9). To use the Arms (10, 1 1) as press arms, insert the two Arm Pins (28) into the holes in the Press Frame (9) and the Arms.
WEIGHT (lbs.) 0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 11 0 11 5 120 125 PRESS ARM (lbs.) 18 26 34 42 50 58 64 70 76 82 88 97 106 11 5 124 133 138 143 148 153 158 166 174 183 191 201 BUTTERFL Y ARM (lbs.) 12 16 20 24 28 33 37 41 45 49 53 57 61 65 69 73 77 81 85 89 93 97 101 105 109 11 2 LOW PULLEY (lbs.
High Cable (35) CABLE DIAGRAMS The cable diagrams below show the proper routing of the High Cable (35), the Arm Cable (36), the Low Cable (37), and the Short Cable (80). Use the diagrams to make sure that the cables and the cable traps have been assembled correctly .
19 TIGHTENING THE CABLES W oven cable, the type of cable used on the weight system, can stretch slightly when it is first used. If there is slack in the cables before resistance is felt, the cables should be tightened.
M10 Nylon Locknut (56) M8 Nylon Locknut (61) M6 Nylon Locknut (58) 19mm Round Inner Cap (49) 50mm Square Inner Cap (44) 25mm x 50mm Inner Cap (42) 45mm Square Inner Cap (45) 38mm Square Inner Cap (48) 50mm Square Outer Cap (50) Dome Cap (47) Large W asher (67) 25mm Round Inner Cap (43) P ART IDENTIFICA TION CHART—Model No.
M6 W asher (63) M8 x 70mm Bolt (51) M6 x 16mm Bolt (59) M10 x 65mm Grade 5 Bolt (73) M10 x 55mm Bolt (69) M10 x 20mm Bolt (75) M10 x 45mm Bolt (68) M10 x 78mm Bolt (71) M10 x 48mm Bolt (77) M10 x 125m.
Key No. Qty . Description Key No. Qty . Description 11 Base 21 Stabilizer 31 Rear Upright 41 Front Upright 51T op Frame 61 Seat Frame 71 Leg Lever 81C u rl Post 91P r ess Frame 10 1 Right Arm 11 1 Lef.
EXPLODED DRA WING—Model No. WESY13820 R0902B 61 81 80 76 56 77 39 41 13 12 33 33 39 68 56 39 77 56 5 39 74 73 44 61 72 25 55 61 60 35 56 55 74 71 56 30 38 40 36 44 45 9 56 55 55 54 42 43 28 58 57 19.
ORDERING REPLACEMENT P ARTS To order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, Monday through Friday , 6 a.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Weider WESY13820 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Weider WESY13820 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Weider WESY13820 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Weider WESY13820 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Weider WESY13820, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Weider WESY13820.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Weider WESY13820. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Weider WESY13820 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
