Manuale d’uso / di manutenzione del prodotto WEEVSY87210 del fabbricante Weider
Vai alla pagina of 30
USER'S MANUAL QUESTIONS? As a manufacturer , we are com- mitted to providing complete customer satisfaction. If you have questions, or if there are missing or damaged parts, please call: Or write: ICON Health & Fitness Ltd. Unit 4 Revie Road Industrial Estate Revie Road Beeston Leeds, LS1 1 8JG UK email: csuk@iconeurope.
2 T ABLE OF CONTENTS IMPORT ANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
The decals shown below have been placed on the weight system in the locations shown. If decals are missing or illegible, please call our Customer Service Department to order free replacement decals (see the back cover of this manual). Apply the decals in the locations shown.
4 BEFORE YOU BEGIN ASSEMBLED DIMENSIONS: Height: 188 cm (74 in.) Width: 102 cm (40 in.) Length: 135 cm (53 in.) Foot Plate Low Pulley Station High Pulley Station Lat Bar Seat Leg Lever Butterfly Arms Press Arm Weight Stack Weight Pin Backrest Stepper Pedals Resistance Cylinders Thank you for selecting the versatile WEIDER ® 8515 weight system.
5 ASSEMBL Y 1 56 High Side of Bracket Handles 3 5 51 Long Side 31 51 14 1 1 27 4 Before beginning assembly , carefully read the following information and instructions: • Place all parts of the weight system in a cleared area and remove the packing materials; do not dispose of the packing materials until assembly is completed.
6 FRAME ASSEMBL Y 2. Slide the Front Upright (42) onto the 5/16” x 2 1/2” Carriage Bolts (1) in the Base (4). Hand tighten a 5/16” Nylon Locknut (3) onto each Carriage Bolt. Do not tighten the Nylon Locknuts yet. Press a 1” Square Inner Cap (65) into the Front Upright (42).
5. Lubricate the pedal axles on the Rear Upright (56). Slide the Left Pedal (79) onto the left pedal axle, and the Right Pedal (78) onto the right pedal axle. Note: Make sure that the Pedals are on the correct sides; the slot- ted brackets must be on the insides of the Pedals.
8 FRAME ASSEMBL Y ARM ASSEMBL Y 9. Press the Weight Tube Bumper (64) into the end of the Weight Tube (63). Insert the Weight Tube into the stack of W eights (25). Be sure that the pins on the Weight T ube are sitting in the pin grooves in the top Weight.
9 ARM ASSEMBL Y 12. Wet the handle of one Press Arm (46) with soapy water . Slide a 5” Plastic Grip (31) onto the handle. Press a 1” Round Inner Cap (49) into the other end of the handle. Press a 1 3/4” Square Inner Cap (44) into the top of the Press Arm.
10 CABLE ASSEMBL Y As you assemble the cables and pulleys in steps 14 through 22, please refer to the CABLE DIAGRAM on page 22 of this manual. 14. Route the Long Cable (23) around the 3 1/2” Pulley (15) attached to the T op Frame (55).
CABLE ASSEMBL Y 17 15 50 20 21 57 15 23 6 66 48 7 16 23 68 16. Route the Long Cable (23) around the “V”- Pulley (6) on the Right Arm (48). Be sure that the Cable is in the groove of the “V”-Pulley and that the Long Cable T rap (50) is turned to hold the Cable in place.
18. Route the Long Cable (23) around the 3 1/2” Pulley (15) attached to the bracket on the T op Frame (55). T ighten the 3/8” x 2” Bolt (12) and the 3/8” Nylon Locknut (21). (Note: This Pulley is pre-assembled. It has been shown disassembled for easy part identifi- cation.
CABLE ASSEMBL Y 12 3 6 9 58 15 21 66 92 9 17 20 21 2 2 10 58 67 10 57 58 20. Route the Short Cable (58) around the 3 1/2” Pulley (15) attached to the upper hole in the Press Frame (17). Be sure that the Cable T rap (66) is in the “3 o’clock” position and that the Cable is routed around the Pulley as shown.
14 CABLE ASSEMBL Y 22. Attach the Long Cable (23) to the Small “U”- Bracket (67) with a 1/4” Nylon Locknut (2) and a 1/4” W asher (10). Do not completely tighten the Nylon Locknut. It should be threaded onto the end of the Cable so only a couple of threads are showing above the Nylon Locknut, as shown in the inset drawing.
15 25. Press a 1 1/2” Square Inner Cap (32) into the Leg Lever (29). Lubricate the 5/16” x 2 1/4” Bolt (33). Attach the Leg Lever (29) to the Seat Frame (36) with the 5/16” x 2 1/4” Bolt and a 5/16” Nylon Locknut (3). Insert the 3/8” x 2” Eyebolt (35) into the Leg Lever (29) from the direction shown.
16 28. Make sure that all parts have been properly tightened. The use of the remaining parts will be explained in HOW T O USE THE WEIGHT SYSTEM, beginning on page 17. Before using the weight system, pull each cable a few times to be sure that the cables move smoothly over the pulleys.
17 HOW T O USE THE WEIGHT SYSTEM The instructions below describe how each part of the weight system can be adjusted. IMPORT ANT : When attaching the lat bar or nylon strap, make sure that the attachments are in the correct starting position for the exercise to be performed.
18 A TT ACHING AND REMOVING THE SEA T Set the bracket on the Seat Frame (36) onto the indi- cated pins on the Front Upright (42). Attach the Seat Frame to the Front Upright with the 5/16” x 2 3/4” Carriage Bolt (14) and the Seat Knob (40). For some exercises, the Seat (13) must be removed.
LOCKING THE WEIGHT ST ACK When the weight system is not in use, the Lock Pin (90) and Lock (91) should be attached. Insert the Lock Pin through a Weight Guide (62).
20 WEIGHT PRESS ARM BUTTERFL Y ARM LEG LEVER HIGH PULLEY LOW PULLEY PLA TES (lbs.) (lbs.) (lbs.) (lbs.) (lbs.) To p 2 0 1 0 1 5 1 4 2 4 14 5 2 2 3 6 2 8 5 4 27 0 3 3 5 4 4 4 8 2 39 9 4 2 7 5 6 0 1 1 5.
21 TROUBLESHOOTING AND MAINTENANCE Inspect and tighten all parts often and replace any worn parts immediately . The weight system can be cleaned using a damp cloth and mild non-abrasive detergent. Do not use solvents. TIGHTENING THE CABLES Woven cable, the type of cable used on the weight system, can stretch slightly when it is first used.
22 4 3 2 7 6 5 4 3 2 Weight Stack— 8 1 —Low Pulley 1 —High Pulley Long Cable (23) 5 —Long “U”-Bracket Short Cable (58) TOP V IE W CABLE DIAGRAM The cable diagram below shows the proper routing of the Short Cable (58) and the Long Cable (23).
NOTES 23.
ORDERING REPLACEMENT P ARTS If you encounter any difficulties or problems with this product, contact the ICON Fitness Lifestyle Ltd. of fice, or write: ICON Health & Fitness Ltd.
IMPORT ANT: Assembly is divided into four stages: 1) frame assembly , 2) arm assembly , 3) cable assembly , and 4) seat assembly . The hardware for each stage is packaged separately . W ait until you begin each assem- bly stage to open that parts bag.
1" Round Inner Cap (49) 1" Round Cover Cap (70) 3/4" Round Inner Cap (34) 1/2" x 3/4" Spacer (61) 1 1/2" Square Inner Cap (32) 1 3/4" Square Inner Cap (44) 2" S.
5/16" Nylon Locknut (3) 1/4" W asher (10) 5/16" W asher (8) 1" Retainer (69) 1/4" x 2 1/2" Screw (43) 5/16" x 1 3/4" Bolt (72) 1/4" x 2" Machine Screw.
81 REMOVE THIS P ART LIST/EXPLODED DRA WING FROM THE MANUAL SA VE THIS P ART LIST/EXPLODED DRA WING FOR FUTURE REFERENCE.
Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. See the back cover for information about ordering replacement parts.
23 11 11 8 8 55 27 12 15 44 15 71 23 21 44 21 3 61 60 3 3 5 51 14 19 26 51 25 64 63 3 76 72 9 92 3 3 4 1 27 65 41 10 43 3 21 6 50 7 42 7 50 6 21 69 70 69 70 47 48 44 45 44 45 52 53 39 49 62 2 10 67 54.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Weider WEEVSY87210 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Weider WEEVSY87210 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Weider WEEVSY87210 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Weider WEEVSY87210 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Weider WEEVSY87210, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Weider WEEVSY87210.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Weider WEEVSY87210. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Weider WEEVSY87210 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.