Manuale d’uso / di manutenzione del prodotto 9940 del fabbricante Weider
Vai alla pagina of 33
® USER’S MANUAL Model No. WESY97310 Serial No. The serial number is found in the location shown below . Write the serial number in the space above. Serial Number Decal Patent Pending Visit our website at www .
2 Important Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Before Y ou Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3 ASSEMBLED DIMENSIONS: Height: 77 in. Width: 80 in. Depth: 55 in. Low Pulley Station Foot Plate Leg Lever Press Arms Backrest Curl Pad Butterfly Arms Ab Pulley Station Weight Stacks Leg Press Lever Thank you for selecting the innovative and versatile WEIDER ® PRO 9940 home gym.
4 Note: This introduction will save you more time than it takes to read it! Identifying Parts T o help you identify the small parts used in assem- bly , we have included a P ART IDENTIFICA TION CHART located in the center of this manual.
1. Before beginning, make sure that you have read and understood the information on page 4. Locate and open the parts bag labeled “FRAME ASSEMBL Y .” See drawing 1a. Press a 2” Square Inner Cap (28) into each end of the Butterfly Base (4). Press two 2” Square Inner Caps (28) into the Weight Base (5).
3. Place the bracket on the lower end of the Butterfly Upright (1) over the indicated 5/16” x 2 1/2” Carriage Bolts (92) in the Butterfly Base (4). Hand tighten two 5/16” Nylon Locknuts (64) onto the Bolts. Do not tighten the Nylon Locknuts yet.
7. Press a 1” Square Inner Cap (98) into the small tube on the Press Upright (2). Place the bracket on the lower end of the Press Upright (2) over the indicated 5/16” x 2 1/2” Carriage Bolts (92) in the Press Base (6). Hand tighten two 5/16” Nylon Locknuts (64) onto the Bolts.
8 10. Lubricate the 3/8” x 3” Bolt (88). Attach the Leg Press Lever (83) to the Press Base (6) with the Bolt and a 3/8” Nylon Locknut (50). Do not overtighten the Nylon Locknut; the Leg Press Lever must pivot easily . 10 1 1. Place two Weight Bumpers (51) over the indicated holes in the Weight Base (5).
9 14. Attach the Weight T op Frame (66) to the Press T op Frame (9) with one 3/8” x 2 3/4” Bolt (46), a Support Plate with 4” center holes (94), and a 3/8” Nylon Locknut (50). Slide a 3 1/2” Pulley (24) with a Cable T rap (25) onto a 3/8” x 4” Bolt (78).
15 15. Attach each of the four Weight Guides (15) to the Weight T op Frame (66) with a 3/8” x 3 3/4” Bolt (59), a 3/8” Flat W asher (48), and a 3/8” Nylon Locknut (50). Important: Go back and fully tighten all Nylon Locknuts used in steps 1 through 15.
11 20. Locate and open the parts bag labeled “PULLEY BAG 2.” Remove one “V”-Pulley (27) from the bag. Leave the remaining pulleys in the bag for identification of the Pro Pulley . Wrap the Butterfly Cable (73) around a “V”-Pulley (27) in the direction shown.
12 23. Attach the Butterfly Cable (73) to the bracket on the Right Butterfly Arm (1 1) with a 3/8” x 1” Bolt (84) and two 3/8” Nylon Jamnuts (63). Note: The loop on the Cable and the two Nylon Jamnuts must be mount- ed underneath the welded bracket.
13 26. Wrap the Ab Cable (74) around a 3 1/2” Pulley (24) in the direction shown. Attach the Pulley to the Small Pulley Bracket (22) with a 3/8” x 1 3/4” Bolt (57) and a 3/8” Nylon Locknut (50). Make sure the Pulley Bracket is oriented as shown.
14 29. Wrap the Ab Cable (74) around a 4 1/2” Pulley (82) in the direction shown. Attach the Pulley inside the indi- cated bracket on the Weight T op Frame (66) with a 3/8” x 1 3/4” Bolt (57) and a 3/8” Nylon Locknut (50). Make sure the threaded end of the Ab Cable is routed through the bracket, as shown.
15 31. Remove a Pro Pulley (26) from the bag labeled “PULLEY BAG 2. Identify the Low Pulley Cable (75). It is approximately 143 1/2” long and it has a ball on one end and a loop on the other . Route the end with the loop through the slot in the cable guide on the Butterfly Base (4).
16 35 75 46 48 48 63 35. Attach the loop on the end of the Low Pulley Cable (75) to the indicated hole in the Small Leg Lever (41) with a 3/8” x 2 3/4” Bolt (46), two 3/8” Flat W ashers (48), and a 3/8” Nylon Jamnut (63). 36. Remove a Pro Pulley (26) from the bag labeled “PULLEY BAG 2.
17 39. Important: Although the following steps are not difficult to perform, the correct routing of the cable is critical to the functioning of the home gym.
18 43. Wrap the Press Cable (72) around a 3 1/2” Pulley (24) in the direction shown. Attach the Pulley and a Cable T rap (25) to the indicated hole on the far side of the Leg Press Lever (83) with a 3/8” x 4 3/4” Bolt (60) and a 3/8” Nylon Jamnut (63).
19 47. Route the threaded end of the Press Cable (72) around the 3 1/2” Pulley (24) that was mounted on the bracket on the Weight Base (5) in an earlier step. 47 24 5 72 48. Wrap the Press Cable (72) over a 4 1/2” Pulley (82) in the direction shown.
20 Seat Assembly 50. Locate and open the parts bag labeled “SEA T ASSEMBL Y .” Attach the Backrest (12) to the indicated holes in the Butterfly Upright (1) with two 1/4” x 2 1/2” Bolts (79) and two 1/4” Flat W ashers (71). 50 79 79 1 12 71 51.
21 Miscellaneous Assembly 52. Insert a 1/4” x 2 1/2” Carriage Bolt (45) through the center hole in a Seat Plate (65). Attach the Seat Plate to a Seat (13) with two 1/4” x 3/4” Bolts (49).
22 56 56. Apply the WEIDER PRO 9940 decal in the location shown. Important: The warning decals shown below have been attached to the home gym in the locations shown. If a decal is missing or illegible, please call our customer hotline at the number on the front cover of this manual to order a replacement decal.
23 Cable Diagrams The cable diagrams below and on the next page show the proper routing of the Butterfly Cable (73), the Ab Cable (74), the Low Pulley Cable (75) and the Press Cable (72).
24 14 2 1 5 15 13 6 9 3 7 11 4 8 10 12 Press Cable (72).
25 ADJUSTING THE LEG PRESS PLA TE T o adjust the position of the Leg Press Plate (55), pull out the Lock Pin (91) and slide the Adjustment T ube (90) backwards or forwards in the bracket on the Leg Press Lever (83). Line up one of the adjustment holes in the Adjustment T ube with the hole in the bracket and re-insert the Lock Pin.
26 Slack can be removed form the Press Cable (72) by moving one or both of the “V”-Pulleys (27) on the Press Cable. One “V”-Pulley (27) is attached to the small tube on the Press Upright (2). There are three free holes in the small tube, and you can move the “V”-Pulley to any one of them to tighten the cables.
27 The threaded ends on the Press Cable (72) and the Ab Cable (74) that are attached to the weight stacks can also be used to tighten the cables. T o tighten the Ab Cable (74), remove the “U”-Bracket (97) from the Short Weight Tube (17) by removing the 5/16” x 1 3/4” Bolt (96) and the 5/16” Nylon Locknut (64).
3/8" Nylon Locknut (50) 3/8" Nylon Jamnut (63) 5/16" Nylon Locknut (64) 1” T ap Screw (80) 3/8" x 2" Bolt (54) 1/4" Flat W asher (71) 5/16" x 1 3/4" Bolt (96).
3/8" x 3 1/2" Bolt (56) 3/8" x 4 3/4" Bolt (60) 3/8" x 2 3/4" Bolt (46) 3/8" x 3" Bolt (88) 3/8" x 3 1/2" Carriage Bolt (95) 3/8" x 3 3/4" B.
3/4" Round Inner Cap (43) 1” Retainer Ring (31) 1" Round Outer Cap (38) 1" Square Inner Cap (98) 1 3/4" Square Inner Cap (35) 1" Round Inner Cap (76) 1" Round Inner Cap.
Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. Part List—Model No. WESY97310 R0601A Key No. Qty .
46 57 57 59 59 24 50 24 46 78 56 60 59 87 62 52 50 87 64 64 25 63 24 89 92 92 95 64 64 30 30 43 51 89 80 25 24 54 62 63 50 24 25 50 88 24 60 63 25 24 92 92 101 102 89 87 64 71 79 68 50 24 57 22 57 50 .
ORDERING REPLACEMENT P ARTS T o order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, Monday through Friday , 6 a.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Weider 9940 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Weider 9940 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Weider 9940 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Weider 9940 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Weider 9940, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Weider 9940.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Weider 9940. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Weider 9940 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
