Manuale d’uso / di manutenzione del prodotto S-460TM del fabbricante Weber
Vai alla pagina of 32
43267 US 08/06/08 LP G AS GRILL Built-In LP Gas Gr ill Installation Guide #43267 S-460 ™ S-660 ™ YOU MUST READ THIS OWNER’S GUIDE BEFORE OPERATING YOUR GAS GRILL DANGER If you smell gas: 1. Shut off gas to the appliance. 2. Extinguish any open flames.
2 WWW . WEBER.COM ® D ANGER Failur e to f ollow the Dangers, W arnings and Cautions contained in this Owner’ s Manual may result in ser ious bodily injury or death, or in a fir e or an explosion causing damage to property . W ARNINGS Do not stor e a spare or disconnect ed liquid propane cylinder under or near the barbecue.
3 WWW . WEBER.COM ® 3 GENERAL CONS TRUCTION DET AILS Summit ® Built-In unit and all other accessory units should be on site befor e construction begins. All dimensions hav e a tolerance of plus or minus (+/-) 1 / 4 inch (6.35 mm). The grill frame rests dir ectly on the Island Structure t op finished surface .
4 WWW . WEBER.COM ® OR S-460 ™ S-660 ™ P ARTS LIST Lid - 1 Cookbox - 1 Lid - 1 Cookbox - 1 F ront F rame Rail - 1 Rear F rame Rail - 1 Rear P anel Assembl y - 1 Bott om Shelf - 1 Left Door - 1 Ri.
5 WWW . WEBER.COM ® 5 P ARTS LIST Flav orizer ® Bars - 8 - 12 Stainless Steel Cooking Grat es - 2 - 3 Collection T ra y - 1 Catch-P an Holder - 1 Catch-P an - 1 Disposable Drip P ans - 2 Right F ron.
6 WWW . WEBER.COM ® 1 1 2 2 3 1 2 Arr ow stic ker s on F rame Rail (1) and Lef t Side P anel (2) should point to war d each other (shown abov e). Door St op Brac ket (3) should be positioned as shown (lef t).
7 WWW . WEBER.COM ® 7 3 A TTENTION! Do not fully tighten scr ews. Clips should slide freel y when installed. 4 ASSEMBL Y.
8 WWW . WEBER.COM ® 5 6 Back ASSEMBL Y.
9 WWW . WEBER.COM ® 9 7 ASSEMBL Y.
10 WWW . WEBER.COM ® CA UTION: Use two people to lif t and install the Summit ® Built-In frame assembly . A) Lif t the frame assembly int o the “island” structure opening. Make sure the frame is r esting lev el on the finished surface of the structur e.
11 WWW . WEBER.COM ® 11 9 10 A (1) S-460™ S-660™ A) Apply a bead of silicone sealant (1) around the perimeter and front edges of the grill that are in contact with the “island” structure. This will pre vent moistur e seepage. The sealant you use must ha ve a t emperature rating abov e 120°F (48.
12 WWW . WEBER.COM ® B A TTER Y HOUSING WIRING 1 BLA CK WIRE 2 GREEN WIRE 3 RED WIRE 4 RED WIRE W ARNING: Make sure that all contr ol knobs are tur ned to the OFF position befor e connecting the gas supply and oper ating the grill.
13 WWW . WEBER.COM ® 13 ASSEMBL Y 13 12 (1) (2) (3) Note: Secure wire t o side panel. Requir es 3 “D” alkaline bat teries (Included). Use alk aline bat teries only . Do not mix old and new bat teries or dif ferent types of bat teries (standard, alk aline or rechargeab le).
14 WWW . WEBER.COM ® ASSEMBL Y S-660™ S-460™ 14 16 15 S-660™ S-460™.
15 WWW . WEBER.COM ® 15 S-660™ S-460™ A B C 17 Match Holder ASSEMBL Y.
16 WWW . WEBER.COM ® 18 1/4" (6.35 mm) Drill Bit ASSEMBL Y A TTENTION! Befor e drilling any holes f or the rear v ent make sure the cookbo x is f lush with the front of the gr ill frame.
17 WWW . WEBER.COM ® 17 S-660™ S-460™ 19 ASSEMBL Y 20 S-460 ™ S-660 ™.
18 WWW . WEBER.COM ® S-660™ S-460™ 21 22 S-660 ™ S-460 ™ ASSEMBL Y.
19 WWW . WEBER.COM ® 19 ASSEMBL Y 23 S-660™ S-460™.
20 WWW . WEBER.COM ® 24 S-460 ™ S-660 ™ ASSEMBL Y.
21 WWW . WEBER.COM ® 21 S-660 ™ S-460 ™ S-660 ™ S-460 ™ S-660 ™ + AAA + AAA + AAA 25 - 1 - 2 - 2 - 4 The Weber Grill Out ™ Handle Light has a “Tilt Sensor”: Lid up - ON / Lid Closed - OFF. The power button (a) activates or deactivates the “Tilt Sensor.
22 WWW . WEBER.COM ® TYPIC AL BULK PROP ANE GA S SUPPL Y INST ALLA TION BUIL T -IN G AS LINE L OCA TIONS Note: Leave an access in the “island” structure for g as supply and regulat or ser vice that is not inside the grill structure.
23 WWW . WEBER.COM ® 23 Ta b l e 6.2(a) Maximum Capacity of Metallic Pipe in Cubic F eet of Gas per Hour for Gas P ressures of 2 psi or Less and a Pr essure Dr op of 0.
24 WWW . WEBER.COM ® TYPIC AL 20 LP PROP ANE GA S SUPPL Y INST ALLA TION GAS SUPPL Y The remot e tank enclosure kit pro vide with you grill shall be used f or installations using a 20 lb LP cylinder , mounted in an “island” str ucture .
25 WWW . WEBER.COM ® 25 OPERA TING W ARNING: Only use the W eber ® T ank Enc losure Kit outdoors in a well-v entilated ar ea. Do not use in a garage, building, breezew ay or any other enc losed area. W ARNING: Y our W eber ® T ank Enclosure Kit shall not be used under an unprot ected combustib le roof or o ver hang.
26 WWW . WEBER.COM ® L OCA TING Y OUR LP T ANK ENCLOSURE KIT When det er mining a suitab le location for your LP T ank Enclosur e Kit installation, give at tention to concerns such as pro ximity to traf fic paths, and k eeping any gas suppl y lines as shor t as possible .
27 WWW . WEBER.COM ® 27 2 4 8 4 2 4 2 2 P ARTS LIST Hose and regulat or - 1 T ank stand - 1 T ank stand base - 1 T ank Scale - 1 1/4-20 nut - 6 Nylon washer - 1 2 1/4-20 x 1/2” bolt - 6 Cylinder gl.
28 WWW . WEBER.COM ® 3 4 MOUNTING THE LP T ANK BRA CKET Mount the LP tank brac ket to the right hand side of the enclosure opening using non corr osive har dware . Mounting holes are pro vided on the sides and bott om of your LP tank brac ket. Be sure t o mount the brack et securley to the enclosure bef ore use.
29 WWW . WEBER.COM ® 29 A B C D E i ii iv v CONNECT GA S SUPPL Y A 58 inch (1 47 .32 cm) corr ugat ed gas line is supplied with the grill. This line needs t o pass through the g as inlet opening to the main gas suppl y . 1) Connect the corrugat ed gas line to the manif old located on the right hand side of grill under the control panel.
30 WWW . WEBER.COM ® VENTILA TION W ARNING: V entillation holes must be pro vided in the struct ure at the t op and bott om to pro vide ventilation in the ev ent of a gas leak.
31 31 NO TES.
©2009 The follo wing trademarks are regist ered in the name of Weber -Stephen P roducts Co ., an Illinois cor poration, located at 200 East D aniels Road, P alatine, Illinois 60067 U .
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Weber S-460TM è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Weber S-460TM - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Weber S-460TM imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Weber S-460TM ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Weber S-460TM, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Weber S-460TM.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Weber S-460TM. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Weber S-460TM insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
