Manuale d’uso / di manutenzione del prodotto GM 2000 EACF del fabbricante WAGNER
Vai alla pagina of 36
Operating Manual GM 2000 EACR - EN GM 2000 EACF - EN 0179 887 GB Edition 03/98 Electrostatic AirCoat Spraygun, with flat or round jet tips.
.
CONTENTS Paragraph Chapter.Page 1 INTRODUCTION 1.1 1.1 Using the manual 1.1 1.2 SAFETY REGULATIONS 1.2 1.3 PTB Conformity certification 1.4 1.4 Product liability and guarantee 1.5 1.5 CE conformity 1.6 2 DESCRIPTION 2.1 2.1 Scope of supply 2.1 2.2 Technical data 2.
CONTENTS Paragraph Chapter.Page 7 ACCESSORIES 7.1 7.1 Round jet tip inserts 7.1 7.2 AirCoat flat tips 7.2 7.3 Filter (standard) 7.3 7.4 Long filter housing and filters 7.3 7.5 Hoses and fittings 7.3 7.6 Special tools 7.3 8 SPARE PARTS CATALOGUE 8.1 8.
1. INTRODUCTION This operating manual contains information and instruction for the operation, repair and maintenance of the spray gun. This equipment can be dangerous if it is not operated in accordance with this Opera- ting manual! Compliance with these instructions constitutes an integral component of the guarantee agreement.
1.2 SAFETY REGULATIONS The safety requirements for electrostatic hand spraying equipement are laid down in the following documents: (Germany) 1) ZH 1/250 Electrostatic enamelling with hand-held spraying equipment (Published by C. Heymanns-Verlag, Cologne) 2) ZH 1/406 Guidelines for jet stream equipment (spraying devices) (Published by C.
1.2.4 Protective breathing masks Although the E-Static AirCoat spraying procedure produces very little mist, it is not completely mist free. There are, in fact, few paint particles to be found in the air.
1.3 PTB Conformity certification GM 2000 EAC - EN 1.4.
1.4 Product liability and guarantee Warranty 12 months / 6 months for multi-shift operation This equipment is covered by the following manufacturing warranty: All parts which prove unusable or the use.
1.5 CE Conformity 1.5.1 Short explanation CE = Communauté Européenne: Products identified with the CE mark have been manufactured and checked according to EU guidelines.
2. DESCRIPTION 2.1 Scope of supply Part No. Quantity Description 0179 018 1 Electrostatic AirCoat spray gun GM 2000 EAC R, with round jet tip R 15 . or 0179 019 1 Electrostatic Air coat spray gun GM 2000 EAC F, without flat jet tip.
● The trigger can be used to activate, one after the other, the various functions of the spray gun. An increase in the tension needed to pull the trigger back will be felt at the position where the material valve opens. ● In order to overcome Faraday cages in corners, the high volta- ge can be switched off by flip- ping the HV switch (F) down.
2.3.2 AirCoat round jet process In the AirCoat process, high pressure of 30 to 150 bar is used to atomize the material. The AirCoat air at 0 to 2.5 bar produces a soft jet, which largely eliminates the problem of overlapping boundaries. The spray jet can be adjusted by turning the nozzle nut.
2.3.4 Electrostatic effect The spray gun produces an electrostatic field by means of the high voltage electrode. As a result, the particles of paint, which have been atomized by the spray gun, are carried to the earthed object by kinetic and electrostatic energy where they adhere, finely distributed, to the object being sprayed.
3. PREPARATION BEFORE STARTING WORK Caution The operating instructions and the safety regulations for the additional system components used must be read before starting-up . This spray gun must be used a part of an AirCoat-Electrostatic spraying system.
Empty page GM 2000 EAC - EN 3.2.
4. STARTING WORK, AND HANDLING Caution See SAFETY REGULATIONS in chapter 1. 4.1 Preparation ● Locking of spray gun! Turn locking nut clockwise until stop (viewed from back of gun) ● Check that spraying pressures are suitable. ● Check that all connections are tight and do not leak.
4.4 Cleaning of clogged round jet tips 1. By means of tip spanner (A), loosen tip insert (B) by a half turn. 2. Remove tip spanner and briefly pull trigger. Caution , never spray into an enclosed vessel. 3. After cleaning the tip retighten. 4.5 Exchange of Aircoat round jet tip insert (EAC round) 1.
4.7 Replacing AirCoat flat jet tips 1. Switch off control unit. 2. Relieve spray gun and system pressure! 3. Lock spray gun. Turn locking screw clockwise until stop. (look in spray- ing direction) 4. Unsrew cap ring (I) and remove air cap (H). 5. Remove AirCoat tip insert (F) and brush cleaning solvent until all tra- ces of paint are dissolved.
Empty page GM 2000 EAC - EN 4.4.
5. MAINTENANCE Caution See SAFETY REGULATIONS in chapter 1. Attention The spray gun and the system must be cleaned every day. Use only the cleaning sol- vent recommended by the material manufacture. Never immerse the spray gun into the solvent. The following points must be observed before every maintenance works: ● Switch off control unit.
5.2 Dissassembly of AirCoat nozzle body (round jet) 1. Unscrew tip nut. 2. Remove nozzle body (3) with spanner (B) 3. Unscrew tip insert (1) with tip spanner (A) 4. Push threaded nozzle fitting (2) backwards out of the nozzle body (3). 5. Handle the round-jet tip insert (1) and threaded fitting (2) with care, do not clean with sharp metal objects.
5.4 Adjustment of the valve rod seal In case paint leaks at the valve rod near the trigger: 1. Pull trigger and throughly clean paint channel with solvent. 2. Tighten the sealing screw (A) ca- refully with universal spanner 3. If leaking continues, see chapter 5.
5.6 Exchange of paint channel ● if the round jet nozzle is fitted 1. Unscrew tip nut (1). 2. Unscrew tip body (2) with universal spanner. 3. Unscrew seal screw (3) with paint channel assembly tool. 4. Remove paint channel. Assemble in reverse order, use screw (3) again.
6. TROUBLE SHOOTING AND SOLUTIONS GM 2000 EAC - EN 6.1 Problem Insufficient material output Poor spray pattern Leaking air valve Poor wrap round or electrostatic effect Back spraying No electrostatic .
Empty page GM 2000 EAC - EN 6.2.
7. ACCESSORIES 7.1 Round jet tip inserts The round jet tips are especially suited to spray pipes, profiles and complex workpieces. Part-No. Marking Volume flow Jet width Recommended filter 1) 2) 0132 720 R 11 0.160 appr. 250 mm 0132 721 R 12 0.220 appr.
7.2 AirCoat flat tips AirCoat flat jet tips are used for fast, economic application of material to flat workpieces. Part Marking size Spraying Volume Jet Recommended number mm / inch angle flow 1) width 2) filter 0128 564 07.40 0.18-0.007 40 0.19 160 0128 550 09.
7.3 Filter (standard) 7.4 Long filter housing and and filters 7.5 Hoses and fittings 7.6 Special tools GM 2000 EAC - EN 7.3 Description Mesh Part No. for 1 pc. Part No. for 10 pcs. For use with nozzle sizes round flat Gun filter, red 180 0034 383 0097 022 R 11 - R 15 .
Empty page GM 2000 EAC - EN 7.4.
8. SPARE PARTS CATALOGUE 8.1 How to order spare parts? Always supply the following information to ensure delivery of the right spare part: Part No., description and quantity. The quantity need not be the same as the number given in the "Quantity" column.
8.3 Spare parts list GM 2000 EAC - EN 8.2 Item Part No. K Quantity Description 2 0179 354 1 Positioning bush 3 9900 962 1 Countersunk screw M3x12 4 0179 564 1 Data plate GM 2000 EAC R EN 4 0179 569 1 .
39 38 40 41 42 48 49 37 50 55 51 52 53 54 GM 2000 EAC - EN 8.3.
Empty page GM 2000 EAC - EN 8.4.
.
England / United Kingdom WAGNER Spraytech (UK) Lt. Telephone ++44 / (0)1295/ 265 353 Haslemere Way Telefax ++44 / (0)1295/ 269 861 Tramway Industrial Estate GB- Banbury OXON OX16 8TY E-Mail: enquiry@wagnerspraytech.co.uk Deutschland / Germany J. WAGNER GmbH Telephone ++49/ (0)7544 / 5050 Otto-Lilienthal-Str.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il WAGNER GM 2000 EACF è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del WAGNER GM 2000 EACF - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso WAGNER GM 2000 EACF imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul WAGNER GM 2000 EACF ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il WAGNER GM 2000 EACF, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del WAGNER GM 2000 EACF.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il WAGNER GM 2000 EACF. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo WAGNER GM 2000 EACF insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
