Manuale d’uso / di manutenzione del prodotto ZJ4116QA del fabbricante Wachsmuth & Krogmann
Vai alla pagina of 21
9 SPEED DRILL PRESS Item# 7149 Model # ZJ4116QA PLEASE READ AND SAVE ALL INSTRU CTIO NS TO ENSURE THE SAFE AND EFFECTIVE USE OF THIS TOOL. TABLE OF CONTENTS.
1 Index P. 1 Important Safety Instructio ns P. 2 Safety Instruction for Drill Press P. 3 - 7 General Safety Rules P. 8, 9 List of Main Parts P. 10 Tech. Specifications, Con tents of Packaging P. 11 Assembly and Operation P. 12 - 16 Maintenance P. 17 Trouble Shooting P.
2 IMPORTANT SAFETY INSTRUCTIONS PLEASE READ THESE INSTRUCT IONS CA REFULLY TO ENSURE THE SAFE AND EFFECTIVE USE OF THIS TOOL. WARNING: READ ALL INSTRUCTO NS. Failure to follow the IMPORTANT SAFEGU ARDS listed BELOW, and other basic sa fety precauti ons, may result in serious personal injury.
3 perform its intended fun ction. Check for alignmen t of moving parts, bind in g of moving parts, breakage of parts, m ounting, and any ot her conditions that may affect its operation. A guard or othe r part that is damaged should be properly repaired or replaced.
4 - Use only one piece, cu p-type, hole cutters . - Do not use fly c utters or multi-part hole cu tters as they can come ap art or become unbalance in use. - Keep speed below 1500rpm. - Drum sanders must ne ver be operated on this drill press at a speed greater than 1800rpm.
5 side of the column. - Whenever possible, position the workpiece to contact the left side of the column – If it is too short to t he table, use table slots or clampi ng ledge around t he outside edge of the table. - When using a drill pres s v ise, always fasten it to a table.
z Wait for tool bi t to stop spinning. z Unplug the drill press. z Make workshop child-proof. Lo ck the shop. Disconnect mas ter switches. Remove the yellow swit ch key.
7 NOTE: Make sure the proper ext ension cord is used and is in good condition. The use of any extension cord will cause some loss of power. To k eep this to a minimum and to prevent overheating and motor burnout, us e the table as below to determine the minimum wire size (A.
GENERAL SAFETY RULES WARNING! Read, understan d and save all instruct ions. Failure to fol low all instructions listed belo w may result in electric sh ock , fire or serious personal injury. The warnings, caution s, and instruct ions discussed in this inst ruction manua l cann ot cover all possible conditions and situatio ns that may occur.
9 with a switch is dangerous and must be repaired. 4. Place the switch in locked or OFF position before making any adjustments, changing accessories or storing the tool. Such preven tive safety measures reduce the risk of starting the tool accidentally.
LIST OF MAIN PARTS Before attempting to use, f a milia rize yourself with all the operating featu res and safety requirements of your drill press. 1. Belt tension lever - The belt tension lever is u sed to release or tighten belt tension.
TECHNICAL SPECIFICATIONS: Model Number ZJ4116QA Rating Voltage 120 Volts, 60Hz, AC Chuck Size 5/8” Net Weight 46.2 Lbs Number Speeds 9 Spindle Stroke 2” Spindle Taper MT2 CONTENTS OF PACKAGING Check all loose parts f rom th e box with the list below.
ASSEMBLY AND OPERATION Warning! For your own safety, do not connect the drill press to the power source until the machine is complet ely as sembled and the entire instruction manual has been read and understood. Assembly 1. Assemble the column (A) Fig.
Fig. 7A 5. Thread the three pinion shaft handles (H) Fig. 8, in t o the three holes located in the h andles holder (J) as shown. Fig. 8 6. IMPORTANT: Make certain the spindle taper (K) Fig. 9, and tapered hole in the chuck (L ) are clean and free of any grease, lacquer or rust preventive coatings.
Fastening drill press to supporting surface If during operation there is any tendency for the machine to ti p over, slide or walk on the support in g surface, the machine base must be secured to the supporting surface with bolts, through the two holes (A) Fig.
5. After the belt is positioned on the desired steps the motor and spindle pulleys, push motor (D) Fig. 14, away from the drill press head until the belt is properly tensioned and tighten tension knob (B). The belt should be just tight enough to prevent slipping.
Using vise for cl amping the workpiece 1. Take out the 2-1/2” vice from the packaging, and put it on the work table. 2. Use four bolts to fasten the vice on the work table, and adj ust the position of vice on the work table at the desired position when operating.
17 MAINTENANCE WARNING: When servicing use on ly identical replacemen t parts. Use of any other parts may create a hazard or cause product damage. WARNING To avoid serious personal injury make sure the drill press is turned OFF and the cord is unplugged from the power source before pe rforming any maintenance or adjust ment.
If you have any question in regards to the oper ation of this po wer tool or are in need of a spare part please contact our service center at: Wachsmuth & Krogmann, Inc. Tel: 1-888-367-7373 (Business hours Mon-Fri 9:00am - 4:00pm CT) Website: http://www.
19 LIMTED WARRANTY Thank you for purchasing a top quality KingCr aft product. This 9 Speed Benchtop Drill Press tem #7149 was tested and me ets our stringent q uality standards.
WARRANTY CARD 9 Speed Benchtop Drill Press, item # 7149, model # ZJ4116QA In case you find thi s product to be defective please send it within the warranty period to our service center. To avoid transport d amages please send the product in th e original packaging.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Wachsmuth & Krogmann ZJ4116QA è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Wachsmuth & Krogmann ZJ4116QA - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Wachsmuth & Krogmann ZJ4116QA imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Wachsmuth & Krogmann ZJ4116QA ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Wachsmuth & Krogmann ZJ4116QA, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Wachsmuth & Krogmann ZJ4116QA.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Wachsmuth & Krogmann ZJ4116QA. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Wachsmuth & Krogmann ZJ4116QA insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
