Manuale d’uso / di manutenzione del prodotto F1D001 del fabbricante Belkin
Vai alla pagina of 40
User Manual ePowerSwitch By: BELKIN 34000179 19 - Sep - 02 Copyright© 2000.
Trademarks IBM, IBM NetView/6000 are trademarks or registered trademarks of International Business Machines Corp. Hewlett - Pa ckard, HP, HP Open View are trademarks or registered trademarks of Hewlett - Packard Company.
Table of Contents i Table of Contents Introduction ........................................................................... 1 ePowerSwitch Features .................................................... 1 Status LEDs .................................
ii ii Telephone access interface ........................................... 27 Appendix .............................................................................. 30 Reference ......................................................................
1 Introduction The ePowerSwitch is a network - manageable, intelligent power control unit designed to provide control of power for up to eight electrical devices in Internet age.
2 2 ? ? Works with all major NMSs on Ethernet — ePowerSwitch System works with the most widely used Network Management Systems: HP Open View, Sun NetManager, IBM NetView, and many more. ? ? Remote Firmware upgrade support - The ePowerSwitch System supports firmware upgrade through TFTP server remotely.
3 On/Off Buttons – control for each of the corresponding rear socket. Press and hold for 3 seconds to setup up the Remote/local control for each of the corresponding rear socket.
4 4 ePowerSwitch System Package The standard ePowerSwitch System package contains an ePowerSwitch System Unit with supporting hardware and software. ePowerSwitch System Package Contents The components of your package are: ? ? ePowerSwitch System Unit ? ? One 3.
5 for 10Base - T networks. Once connected, it is possible to use the ARP command to set IP address through the network interface. USB Connector – The USB port provides quicker setup compared to the serial setup process. The USB driver files and setup software are both included on the floppy.
6 6 IP Setup This section describes the IP set up & configuration of the ePowerSwitch System when you connect it to the network. There are four dif ferent ways to setup ePowerSwitch . 1. Setup IP address via Ethernet port using the ARP command (first time only), then use a Web browser to setup all the parameters.
7 The following steps guide you in connecting the ePowerSwitch System through the Ethernet port 1. Connect the Ethernet port to the network with the Ethernet cable. 2. Using the following settings in the text mode : c:>arp –s 216.87.151.196 52-54-4c-19-ad- 90 ? ? 216.
8 8 2. Setup via serial port Before setup you need: 1. IP address: Get a valid IP address from adm inistrator. 2. RS232 Cable.(enclose) 3. Dumb terminal software: ex: HyperTerminal in the win95/98, NT, Win2000.
9 The following steps guide you in connecting the ePowerSwitch System through the serial port 1. Connect the RS232 port to a dumb terminal/PC with RS232 c able. 2. Setup terminal software 1. Open terminal software; select “ Property ” in “ File ” category.
10 10 3. Press OK if you have the Windows Communications screen or accept your communication settings in the terminal emulation package. The terminal/PC is now configured to communicate with the ePowerSwitch. 4. Approximately three seconds after you turn on AC power, the terminal displays “Check u - dram…”.
11 Note: The telnet setup procedure is the same as the serial setup. When the configuration is complet ed, remember to save and restart. Serial or Telnet Configuration ePowerSwitch System is temporarily connected to a PC with a terminal emulation package or through telnet connection.
12 12 Figure 4 - IP Address for the ePowerSwitch System and More NOTE: The minimum requirement to operate ePowerSwitch System is to set the IP address. If you want to return to the Main Menu , press Esc key. For m ore information on IP addresses and net masks, see the Reference section of the Appendix in this manual.
13 To Save and Exit If you are satisfied with your configurations, be sure to save them and exit. 3. Set up via USB port Before setup you need: 1. IP address: Get a valid IP address from administrator. 2. USB Cable. ( Enclose ) 3. USB driver and USBSetup file.
14 14 to see the device because the ePowerSwitch takes about 30 seconds to boot. 2. The “U SB - interface power device” name must appear in the System Properties dialog box before you run the USB setup sof tware .
15 3. USB setup is straightforward once the PC has successfully detected USB device. See the following figure. You need to run Device | Update & Restart before closing 4. Telnet Options You can also Telnet to the IP address of the ePowerSwitch Syst em after it has been installed on your network .
16 16 adapter you may access the configuration menu as if you were directly attached to it via the configuration port. Moving cursor in telnet session is tricky . You need to select VT100 cursor which is under Terminal | Preferences | VT100 Arrows . After this setup, moving around menu system is actually easier than in console setup mode.
17 Configuration PPP Configuration PPP connection is useful if it is not possible to make a direct network connection to the ePowerSwitch . A gain the external modem is needed to connect to the front serial port of the NIC Web card of the ePowerSwitch.
18 18 Remote operation procedure 1. The remote user may hang up after three rings when dial in. 2. Ba sed on the content of the PPP configuration, ePowerSwitch will then automatically dial up to the designated ISP and send the e - mail to the designated e - mail address with the assigned IP address from ISP .
19 User Management Administrators can assign the maximum of 4 users to control the outlet..
20 20 Software Update This is the place you can upgrade the firmware when i t is available or bug fix..
21 ePowerSwitch Configuration Each outlet can be individually programmed to enable ring On/Off or reset. Power resume delay is convenient for sequential startup. Name of each outlet can be labeled to whatever you like it to be called. For example, server1, DSL modem, webserver1, etc.
22 22 To enable this safe shutdown function, in both NT and WIN 2000, you need to have three setting for the UPS to configure it. Connect the communication port on the rear of ePowerSwitch to NT or WIN 2000 server with the PC Communication cable.
23 Scheduled shutdown Scheduled shutdown can be accomplished here. Be careful with which outlet you are working..
24 24 Verify The ePowerSwitch Operation 1. After you complete all configuration settings and connect the ePowerSwitch System to the network, check the LINK status . Power and Link lights should be on all the times. Collision light turns on occasionally.
25 Upgrade Firmware TFTP Upgrade With a Web br owser, click on “Software upgrade”, input TFTP server’s IP address and go. Make sure that the firmware file (For example: ups.
26 26 the user data are lost..
27 Telephone Interface You must have the optional phone card installed inside the ePowerSwitch Server for all t he functions discussed here. Please check the dealer for the detail information. Telephone access interface 1. Dial up the ePowerSwitch . 2.
28 28 ePowerSwitch ID Address ePowerSwitch Outlet Function XX X X 01 - 16 1 - 8 ? A - H 0 - Off 9 ? All 1 - On 2 - Reset Every command must add “ # ” in the end.
29 9. User enter 888XXX…..# or whatever previous password, then ePowerSwitch respon ds with three short beeps acknowledge access granted. Then user enter new password as following: 888XXXXXXXXXX#, a.
30 30 Appendix This appendix has three sections: Reference , Glossary , and Troubleshooting . Reference This section discusses Communities, IP Addresses, Sub net masking, and routers/gateways. Communities A community is a string of printable ASCII characters that identifies a user group with the same access privileges.
31 IP addresses appear in dotted decima l (rather than in binary) notation. Dotted decimal notation divides the 32 - bit value into four 8 - bit groups, or octets, and separates each octet with a period. For example, 199.217.132.1 is an IP address in dotted decimal notation.
32 32 segments the network address into 100 subnetwork addresses. (If the Class B network address is 150.1.x.x, the address can be segmented further from 150.1.1.x through 150.1.100.x.) A sub net mask is a 3 2 - bit value that distinguishes the network ID from the host ID for different subnetworks on the same logical network.
33 first three octets. Gateways Gateway, also referred to as a router, is any computer with two or more network adapters connecting to different physical networks.
34 34 Glossary The Glossary section defines the terms used in the ePowerSwitch System - MP environment. Agent Implemented SNMP applications in network elements (hosts). Agents perform the network management’s functions as requested by the network administrator from an NMS.
35 NO Normally Open — Refers to a contact switch that is normally open. OID Object Identifier — The variables defined in a MIB. Personality The current device specific software uploaded to the ePowerSwitch System Router A computer that manages traffic between different network segments or different network topologies.
36 36 Troubleshooting Problem: The TES (Terminal Emulation Software) does not display anything. Solution: Make sure the TES’s communication parameters are correct. They shoul d be 115200 baud rate, no parity, 8 - data bits, and 1 stop bit. The cable is a null serial cable.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Belkin F1D001 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Belkin F1D001 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Belkin F1D001 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Belkin F1D001 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Belkin F1D001, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Belkin F1D001.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Belkin F1D001. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Belkin F1D001 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
