Manuale d’uso / di manutenzione del prodotto PBE-5AC-500 del fabbricante Ubiquiti Networks
Vai alla pagina of 24
High-Performance Integrated InnerFeed ™ airMAX ® ac Bridge Model: PBE-5AC-500.
Introduction Thank you for purchasing the Ubiquiti Netw orks® PowerBeam ™ . This Quick Start Guide is designed to guide you through the installation, and show you how to access the airOS® Configuration Interface. This Quick Start Guide also includes the warranty terms and is for use with the PowerBeam5ac , modelPBE-5AC-500.
Hardware Overview Bottom View Cable Door Rear Housing T echnology Ethernet Port Release Button Slot Dish Bracket Release Button Dish Reflector Alignment Pins Reset Button Antenna Feed Radome Reset Button T o reset to factory defaults, press and hold the Reset button for more than 10 seconds while the P owerBeam is already poweredon.
Release Button After you assemble the Po werBeam, check the Release button; it should be fully engaged in the Release Button Slot of the Rear Housing . This ensures that the Antenna Feed is locked into place . If you need to remove the Antenna Feed , you must depr ess the Release button first.
Application Examples The Pow erBeam mounted outdoors with the Dish Reflector installed provides directional outdoor cover age (gain is reflector-dependent). The Pow erBeam mounted outdoors without the Dish Reflector installed provides outdoor-to-indoor cov erage using the 3 dBi Antenna Feed only .
Installation 1. Align and insert the tabs of the Dish Bracket into the slots of the Dish Reflector . Rotate the Dish Bracket counter-clockwise until the tabs lock into place. 20 10 10 0 2. Line up the Alignment Pins of the Rear Housing with the alignment holes of the Dish Bracket .
3. Push in the sides of the Cable Door and detach it from the Rear Housing . 20 10 0 10 4. Attach the Antenna Feed : a. I nsert the Antenna Feed into the Rear Housing , and push until it locks into place with a click. b. Lightly pull the Antenna Feed to ensure that it is locked into place and the Release button is fully engaged.
5. Connect the Ethernet cable: a. Connect an Ethe rnet cable to the Ethernet Port of the Antenna Feed . b. Re-attach the Cable Door to the Rear Housing .
7. Insert the U-Bolt into the Pole Clamp and Dish Brack et . Secure each end of the U-Bolt with a Flange Nut. 20 10 10 0 25 N-m Note: The mounting assembly can accommodate a Ø 32 - 56 mm pole. 8. Align the arrows on the bott oms of the Radome and Dish Reflector so the Drain Holes on the Radome point downward .
9. Connect the other end of the Ethernet cable from the PowerBeam t o the Ethernet port labeled POE on the Gigabit PoEAdapter . 10. Connect an Ethernet cable from your LAN or computer to the Ethernet port labeled LAN on the Gigabit PoE Adapter . 11.
Accessing airOS Verify c onnectivity in the airOS Configuration Interface. 1. Make sure that your host machine is connected via Ethernet to the Po werBeam. 2. Configure the Ethernet adapter on your host syst em with a static IP address on the 192.168.
Installer Compliance Responsibility Devices must be professionally installed and it is the professional installer's responsibility to make sure the device is operated within local country regulatory requirements. The Output Power field is provided t o the professional installer to assist in meeting regulatory requirements.
Specifications PowerBeam PBE-5A C-500 Dimensions Radome Excluded Radome Included 520 x 520 x 308 mm (20.47 x 20.47 x 12.13") 525 x 525 x 315 mm (20.
Safety Notices 1. Read, follow , and keep these instructions. 2. Heed all warnings. 3. Only use attachments/accessories specified by the manufacturer . W ARNING: Do not use this product in location that can be submerged by water . W ARNING: A void using this product during an electrical storm.
Limited W arranty UBIQUITI NETWORKS, Inc (“UBIQUITI NET WORKS”) warrants that the product(s) furnished hereunder (the “Product(s)”) shall be free from defects in material and workmanship for a period of one (1) year from the date of shipment by UBIQUITI NETWORKS under normal use and operation.
Disclaimer EXCEPT FOR ANY EXPRESS W ARRANTIES PROVIDED HEREIN, UBIQUITI NETWORKS, ITS AFFILIATES, AND IT S AND THEIR THIRD P ARTY DA T A, SERVICE, SOFTWARE AND HARDW ARE PROVIDERS HEREBY DISCLAIM AND .
Note Some countries, states and provinces do not allo w exclusions of implied warranties or conditions, so the abov e exclusion may not apply to you . Y ou may have other rights that vary from country to country, state to state, or province t o province.
This radio transmitter FCC ID: SWX-NBEM5A C has been approved by FCC to operate with the antenna types listed belo w with the maximum permissible gain and required antenna impedance for each antenna type indicated.
Les utilisateurs devraient également noter que radars haute puissants sont alloués comme principaux utilisateurs (c’est-à-dire les utilisateurs de priorité) des bandes et 5650 à 5850 MHz et que ces radars pourraient causer des interférences ou dommages aux dispositifs LAN.
RoHS/WEEE Compliance Statement English European Directive 2002/96/EC requires that the equipment bearing this symbol on the product and/or its packaging must not be disposed of with unsorted municipal waste. The symbol indicates that this product should be disposed of separately from regular household waste streams.
Español La Directiva 2002/96/CE de la UE exige que los equipos que lleven este símbolo en el propio aparato y/o en su embalaje no deben eliminarse junto con otros residuos urbanos no seleccionados. El símbolo indica que el producto en cuestión debe separarse de los residuos domésticos convencionales con vistas a su eliminación.
Declaration of Conformity Česky [Czech] UBIQUITI NET WORKS tímto prohla uje, e tento UBIQUITI NETWORKS device, je ve shod se základními po adavky a dal ími p íslu n mi ustanoveními sm rnice 1999/5/ES.
Italiano [Italian] Con la presente UBIQUITI NETWORKS dichiara che questo UBIQUITI NET WORKS device, è conforme ai requisiti essenziali ed alle altr e disposizioni pertinenti stabilite dalla direttiva 1999/5/CE.
www .ubnt.com ©2013-2014 Ubiquiti Networks, Inc. All rights reserved. Ubiquiti, Ubiquiti Networks, the Ubiquiti U logo, the Ubiquiti beam logo , airMAX, airOS, InnerFeed, P owerBeam, and TOUGHCable are trademarks or registered trademarks of UbiquitiNetworks, Inc.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Ubiquiti Networks PBE-5AC-500 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Ubiquiti Networks PBE-5AC-500 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Ubiquiti Networks PBE-5AC-500 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Ubiquiti Networks PBE-5AC-500 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Ubiquiti Networks PBE-5AC-500, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Ubiquiti Networks PBE-5AC-500.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Ubiquiti Networks PBE-5AC-500. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Ubiquiti Networks PBE-5AC-500 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
