Manuale d’uso / di manutenzione del prodotto T-106 del fabbricante Troy-Bilt
Vai alla pagina of 14
Owner’s Manual • SET-UP • OPERATION • MAINTENANCE IMPORTANT Read Safety Rules and Instructions Carefully PRINTED IN CANADA OG-4003 Walk Behind Mower Model: T-106.
2 CALLING CUSTOMER SUPPORT • L OCA TE YOUR MODEL NUMBER AND SERIAL NUMBER which appears on your unit and record the information in the space provided below . IMPORTANT: You must have these numbers, along with the date and proof of purchase to receive warranty or service.
GENERAL OPERATION • Read, understand, and follow all instruc - tions on the machine and in the manual(s) before attempting to assemble and operate. Keep this manual in a safe place for future and regular reference and for ordering re - placement parts.
tive and may result in personal injury through contact with the rotating blade. The blade control handle must operate easily in both directions and automatically return to the disengaged position when released. • Never operate the mower in wet grass.
self or your clothes which can ignite. Wash your skin and change clothes immediately . a) Use only an approved gasoline con - tainer . b) Never fill containers inside a vehicle or on a truck or trailer bed with a plastic liner . Always place containers on the ground away from your vehicle before filling.
6 15 º USE THIS SHEET AS A GUIDE TO DETERMINE SLOPES WHERE YOU MAY NOT OPERATE SAFELY. A CORNER OF A BUILDING FOLD ON DOTTED LINE, REPRESENTING A 15 º SLOPE OR A FENCE POST SIGHT AND HOL D THIS LEVE.
UNPACKING • Remove the lawn mower and all parts from the carton. Make certain all parts and litera- ture have been removed from the carton before the carton is discarded. CAUTION: Disconnect spark plug wire. if the wire is not equipped with a rubber boot, see separate engine manual for grounding procedure.
ATTACHING THE BLADE CONTROL CABLE • The brake cable is attached to the engine, and has a “Z” fitting on the loose end. Route the brake cable over the lower handle. Place end of cable through the hole in the control box as shown in figure 3. Push the plastic fitting until it locks into the hole in the throt - tle box.
TO CONVERT YOUR MOWER FROM A MULCHER TO A SIDE DISCHARGE MOWER • Lift mulching plug. Slide the two hooks on the side discharge deflector under the hinge pin on the mulching plug assembly .
FOR THE BEST RESULTS WHEN MULCHING: Clear lawn of debris. Be sure that the lawn is clear of stones, sticks, wire or other foreign objects which could damage the lawnmower.
• Remove the hairpin clips from the weld pins on the handle brackets. Press out on the legs of the lower handle. Remove lower han - dle from the mower . • T urn the lower handle around so the notch on the bottom of the lower handle is facing forward as shown in Figure 10.
CAUTION: Cutting grass in sandy soil condition causes abrasive wear to the blades. After prolonged use, especially in sandy soil conditions, the blade will become worn and lose some of the original shape. Cutting effi - ciently will be reduced and the blade should be replaced.
13 Engine Shroud Chart NOTE: this chart shows all the optional engine shrouds for the lawn mowers covered in this manual. To order replacement parts, please refer to the shroud and hardware applicable to your lawn mower unit.
16 THREE (3) YEAR LIMITED WARRANTY For three (3) years from the date of original purchase of our products, we will either repair or replace, at its option, free of charge, F.O.B. Factory or authorized service firm, any part found to be DEFECTIVE IN MATERIAL and WORKMANSHIP for the original purchaser.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Troy-Bilt T-106 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Troy-Bilt T-106 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Troy-Bilt T-106 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Troy-Bilt T-106 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Troy-Bilt T-106, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Troy-Bilt T-106.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Troy-Bilt T-106. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Troy-Bilt T-106 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
