Manuale d’uso / di manutenzione del prodotto TL-PS110P del fabbricante TP-Link
Vai alla pagina of 60
TL-PS110P Single Parallel Port Fast Ethernet Print Server Rev: 1.1.0 1910010382.
I COPYRIGHT & TRADEMARKS Specifications are subjec t to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other br ands and product nam es are trademarks or registered trademarks of t heir respective holders.
II FCC STATEMENT This equipment has been tested and found to comply wi th the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
III FCC RF Radiation Exposure St atement This equipment complies with FCC RF radiatio n exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter.
IV CONTENTS Chapter 1. Introduc tion ......................................................................................... 1 1.1 Product Overview .....................................................................................................
V Appendix D: Additional In stallation In str uctions ................................................. 54.
TL-PS110P Single Parallel Port Fast Ethernet Print Server 1 Chapter 1. Introduction 1.1 Product Overview The external print servers enhance capability by le tting you place your printers at convenient locations directly on the Ether net network, and by increasing net work printer performance and management.
TL-PS110P Single Parallel Port Fast Ethernet Print Server 2 Chapter 2. Hardware Installation 2.1 Prep aration Before you start, you should prepare the following items: ¾ One printer with a Parallel port ¾ One printer cable ¾ One Router 2.2 Connection Follow the instructions below to connect the print server.
TL-PS110P Single Parallel Port Fast Ethernet Print Server 3 Chapter 3. How to Configure the Print Server 3.1 Using PSWizard in Windows XP/ W indows Vist a/ W indows 7 To connect to the print server using PSWizard, the configuration for Windows XP, Windows Vista and Windows 7 are similar.
TL-PS110P Single Parallel Port Fast Ethernet Print Server 4 3. Then you will enter to the “ Welcome ” page as shown in Figure 3-3. Click Next . Figure 3-3 4. From the “ Select A Print Server ” screen as shown in Figure 3-4, select the print server that you wa nt to configure and click Next .
TL-PS110P Single Parallel Port Fast Ethernet Print Server 5 5. On the Change Settings screen as shown in Figure 3-5, select Yes or No . ¾ Select “ Yes ” if you want to change the settings. The TL-PS110P is produced with no password. Click Next and then appears “ TCP/IP Settings ” screen as shown in Figure 3-6.
TL-PS110P Single Parallel Port Fast Ethernet Print Server 6 Figure 3-6 7. Confirm your settings on the screen in Figure 3-7. Click Next and your changes will be saved as shown in Figure 3-8.
TL-PS110P Single Parallel Port Fast Ethernet Print Server 7 Figure 3-8 8. After that the “ Select a Printer ” page will appear, as shown in Figure 3-9. ¾ If the printer desired has already existed in the list, select it and then click Next and skip to Step 16 to complete the installation.
TL-PS110P Single Parallel Port Fast Ethernet Print Server 8 Figure 3-9 ) Note: To add a new printer, you can also go Start > Printers and Faxes , and then click “ Add a printer ” on the left to begin the following installation as shown in Figure 3-10 .
TL-PS110P Single Parallel Port Fast Ethernet Print Server 9 Figure 3-11 10. Make sure the Automatically detect and install my Plug and Play printer check box is NOT checked. Then click Next . Figure 3-12 11. Check “ Use the following port ” radio button and select “ LPT1: (Recommended Printer Port) ” from the pull-down list.
TL-PS110P Single Parallel Port Fast Ethernet Print Server 10 Figure 3-13 12. Select Manufacturer and Printer from the lists of printer’s driver. Then click Next . Figure 3-14 13. If you already have the printer’ s driver installed, you will be asked whether to keep it or to replace it.
TL-PS110P Single Parallel Port Fast Ethernet Print Server 11 Figure 3-15 14. Then, choose whether y ou want to share the printer with oth er network users, print a test page (please select No .), etc. Select the appropriate radio-button and click Next .
TL-PS110P Single Parallel Port Fast Ethernet Print Server 12 Figure 3-17 16. Then you will see the printer be added to the list. Select the printer and click Next . Follow the step by step instruction to finish the installation. Figure 3-18 17. From Windows system, go to Start > Printers and Faxes and highlight your newly installed printer.
TL-PS110P Single Parallel Port Fast Ethernet Print Server 13 Figure 3-19 18. Select Ports and verify that the print server’s port appears. Figure 3-20 19.
TL-PS110P Single Parallel Port Fast Ethernet Print Server 14 Figure 3-21 ) Note: If you wish to install more prin t servers, repeat the above steps. 3.
TL-PS110P Single Parallel Port Fast Ethernet Print Server 15 Figure 3-22 2. Select and double-click Networking Connections . Figure 3-23 3. Right click Wireless Network Connection , and select Properties .
TL-PS110P Single Parallel Port Fast Ethernet Print Server 16 Figure 3-24 4. Select Internet Protocol (TCP/IP) , and then double click it or click Properties . Figure 3-25 5. Select “Use the following IP address” and input a static IP address 192.168.
TL-PS110P Single Parallel Port Fast Ethernet Print Server 17 Figure 3-26 6. Open a web-browser and type in the IP address of the print server (t he default is 192.168. 0.10) in the address field of the browser to logi n to the web management of the print server.
TL-PS110P Single Parallel Port Fast Ethernet Print Server 18 8. Then the print server web manag ement page w ill appear, with which you can configure all print server settings. Figure 3-29 9. Click “ Setup ” and then choose “ TCP/IP ”. Check “ Use the following TCP/IP Settings ” radio button and then fill in the following parameters.
TL-PS110P Single Parallel Port Fast Ethernet Print Server 19 Figure 3-30 10. Click Save & Restart and then wait the print server to save the changes and restart.
TL-PS110P Single Parallel Port Fast Ethernet Print Server 20 Figure 3-31 11. Enter the “ Internet Protocol (TCP/IP) Properties ” page as shown in Figure 3-32. Fill in the following par ameters. ¾ IP Address: Specify an IP address for your adapter .
TL-PS110P Single Parallel Port Fast Ethernet Print Server 21 Figure 3-32 12. Add a Standard TCP/IP port for the printer. ¾ If you’ve already installed the printe r on your computer, please refer to 3.4.1 If You Have Installed A Printer Before to add a Standard TCP/IP port.
TL-PS110P Single Parallel Port Fast Ethernet Print Server 22 Figure 3-34 3. Follow the steps to set the airport’s IP address. Figure 3-35 4. Open the Safari and log into the TL-PS 110P. Change its IP Address, Subnet Mask and Default Router to 192.168.
TL-PS110P Single Parallel Port Fast Ethernet Print Server 23 Save & Restart . Figure 3-36 Figure 3-37 5. On the MACbook, change the airport’s IP Address, Subnet Mask and Router to 192.
TL-PS110P Single Parallel Port Fast Ethernet Print Server 24 Figure 3-38 6. Click the Ap ple icon > System Performances > Print & Fax to add a Standard TCP/IP port for the printer.
TL-PS110P Single Parallel Port Fast Ethernet Print Server 25 7. Click Printing and then . Figure 3-40 8. Select “ IP Printer ”, and then configure the followi ng parameters. Select “ LPD ” for Protocol, enter 192.168.1.10 for Address and lp1 for Queue.
TL-PS110P Single Parallel Port Fast Ethernet Print Server 26 Figure 3-41 9. Till now you've installed the print server successfully and can print through the TL-PS110P.
TL-PS110P Single Parallel Port Fast Ethernet Print Server 27 Figure 3-42 3.4 Printer Inst allation Other computers in the same local network that need to share the printing should add the Standard TCP/IP port on their system. There’re two conditions.
TL-PS110P Single Parallel Port Fast Ethernet Print Server 28 Figure 3-43 2. Find your installed printer icon, right-click on it, and select Properties .
TL-PS110P Single Parallel Port Fast Ethernet Print Server 29 Figure 3-45 4. Input the exact IP address of print server. Here take s 192.168.0.10 for example.
TL-PS110P Single Parallel Port Fast Ethernet Print Server 30 Figure 3-47 6. Choose LPR , and input the queue name as lp1 . Click OK . Figure 3-48 7. Click Next and then Finish , to complete the wizard.
TL-PS110P Single Parallel Port Fast Ethernet Print Server 31 Figure 3-49 Figure 3-50 8. Click Close and Apply ..
TL-PS110P Single Parallel Port Fast Ethernet Print Server 32 Figure 3-51 Figure 3-52 9. Now, the printer port has been created. 3.4.2 If You Never Install A Printer Before 1.
TL-PS110P Single Parallel Port Fast Ethernet Print Server 33 Figure 3-53 2. Click Add a printer . Figure 3-54 3. Select Add a local printer . Figure 3-55 4.
TL-PS110P Single Parallel Port Fast Ethernet Print Server 34 Figure 3-56 5. Input the IP address of the print server and click Next . The windows will detect the TC P/IP Port.
TL-PS110P Single Parallel Port Fast Ethernet Print Server 35 Figure 3-58 6. On the following page, select Custom and click Settings . And then on the next page, please select LPR as the Protocol and the Queue Name is lp1 . Figure 3-59 7. The windows will ask you to install the driver of the printer.
TL-PS110P Single Parallel Port Fast Ethernet Print Server 36 Figure 3-60 Figure 3-61.
TL-PS110P Single Parallel Port Fast Ethernet Print Server 37 Figure 3-62 8. After that, the new printer is in t he list. And you can enjoy the sharing.
TL-PS110P Single Parallel Port Fast Ethernet Print Server 38 Chapter 4. More Configuration for the Print Server The Print Server contains an embedded web se rver that can be acce ssed through a supported web browser on a WLAN, for exampl e, IE6, Fi refox or above is recommended.
TL-PS110P Single Parallel Port Fast Ethernet Print Server 39 Figure 4-3 4.2 S t atus The Status page shows the current informat ion about the print server as shown in Figure 4-3. By clicking the corresponding tab, you can vi ew the following information, including S ystem , Printer , and TCP/IP .
TL-PS110P Single Parallel Port Fast Ethernet Print Server 40 4.2.1 System Figure 4-4 ¾ Print Server Name: This option allows you to view device name of the print server.
TL-PS110P Single Parallel Port Fast Ethernet Print Server 41 4.2.2 Printer Figure 4-5 ¾ Manufacturer: This option allows you to view manufac turer of the printer. When the printer connected with the print server, it w ill be show in the manufacture box.
TL-PS110P Single Parallel Port Fast Ethernet Print Server 42 4.2.3 TCP/IP Figure 4-6 ¾ Use DHCP/BOOTP: This option allows you to view DHCP/ BOOTP status. If there is a DHCP/BOOTP server on your network, this option a llows the print server to obtain IP-related settings automatically fr om your DHCP server.
TL-PS110P Single Parallel Port Fast Ethernet Print Server 43 Figure 4-7 ¾ E-mail Alert: This option allows you to re ceive alert of the device. ¾ SMTP Server IP Address: Enter the IP Address of the SMTP Server. ¾ Administrator E-mail Address: Enter the e-mail address used to receive alert.
TL-PS110P Single Parallel Port Fast Ethernet Print Server 44 Figure 4-8 ¾ Bi-directional Settings: This option allows you to select t he bi-directional of the print server. There are two ways to select this option, includes Disable or Auto Detect . 4.
TL-PS110P Single Parallel Port Fast Ethernet Print Server 45 Figure 4-9 ¾ Use DHCP/BOOTP: This option allows you to select DHCP/ BOOTP option. If there is a DHCP/BOOTP server on your networ k. This option a llows the print server to obtain IP-related settings automatically fr om your DHCP server.
TL-PS110P Single Parallel Port Fast Ethernet Print Server 46 4.4 Misc 4.4.1 Factory Default Click OK to restore the print server to its Factory Default settings. Figure 4-10 4.4.2 Firmware Upgrade Click Browse… to select the firmware file and then click Firmware Upgrade to upgrade th e firmware of the print server.
TL-PS110P Single Parallel Port Fast Ethernet Print Server 47 Figure 4-11 4.5 Rest art Click OK to reboot the print server. Figure 4-12.
TL-PS110P Single Parallel Port Fast Ethernet Print Server 48 Appendix A: How to Reset the Print Server If you lose the connection with the TL-PS110P by doing wrong configuration, you need to reset it to factory and reconfigure it again. Here are the steps for the resetting 1.
TL-PS110P Single Parallel Port Fast Ethernet Print Server 49 Appendix B: Troubleshooting General Troubleshooting Overview The most common problems, which cause the print server to perform improperly, are covered in this chapter. If a problem still exists after r eading this chapter, please contact your dealer for technical support.
TL-PS110P Single Parallel Port Fast Ethernet Print Server 50 installing the print server." Regarding this problem, there are three possible causes: A. The print server's Node ID you specified in the "arp" co m m a n d i s n o t c o r r e c t .
TL-PS110P Single Parallel Port Fast Ethernet Print Server 51 2. If the solutio n described above is not applicable, you have to fo llow the instructions below to set up the print server's IP address. For the purpose of explanation, we assume the NT server is on Segment A and its IP address is 192.
TL-PS110P Single Parallel Port Fast Ethernet Print Server 52 Appendix C: Frequently Asked Questions 1) Question A: Print jobs are sent to the print queue success fully, but fail to be sent to the pr inter. Possible explanations: 1. The Print server Name/Print Queue configuration is incorrect.
TL-PS110P Single Parallel Port Fast Ethernet Print Server 53 1) Check the wireless network connection, es pecially from the workstation running the PSAdmin to the print server unit. 2) Upgrade the print server agai n by PSAdmin or WEB browser. 4) Question D The setup Wizard can’t find print server.
TL-PS110P Single Parallel Port Fast Ethernet Print Server 54 Appendix D: Additional Installation Instructions Panasonic KX-P6100/6300/6500 If you are using a Panasonic KX-P6100/6300/6500 lase r print .
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il TP-Link TL-PS110P è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del TP-Link TL-PS110P - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso TP-Link TL-PS110P imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul TP-Link TL-PS110P ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il TP-Link TL-PS110P, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del TP-Link TL-PS110P.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il TP-Link TL-PS110P. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo TP-Link TL-PS110P insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
