Manuale d’uso / di manutenzione del prodotto SD-R1312 del fabbricante Toshiba
Vai alla pagina of 16
TOSHIBA AMERICA INFORMA TION SYSTEMS STORAGE DEVICE DIVISION IRVINE, CALIFORNIA SD-R1312 CD-R W/D VD-R OM COMBO DRIVE USER MANU AL.
CONTENTS Introductio n .............................................................................. 1 Setup ........................................................................................ 3 Using the Com bo Drive ...........................
1 INTR ODUCTION – SD-R1312 General Features Reads and record s digital data on CD-R/-RW discs at 32X/10X 3-way Disc Eject (ej ect button, software, emergency eject hole ) Average Random Access Time .
Front Panel Figure 1.SD-R1312 DVD Write able Drive Front Panel Loading Tray Load disc using tray. Busy Light LED The LED lights green or amber whe n the drive is operating (LED is amber whe n drive is writing.) Eject Button The Eject button is used to open the disc tra y so you can install or remove a disc.
3 SETUP – SD-R1312 The following steps must be performe d to properly install your drive: • Set Drive J umper Settings • Connect Audio Cable • Attach IDE BUS Cable • Attach P ow er Cable • Mount Drive Jumper Settings The mode select jumpers are 6 straight angle pi n s located on the rear of the Combo drive.
4 Placing Combo Drive inside your Computer Now that you have set the jumpers, you are read y to install your Combo drive inside your computer. Important Note: Disconnect power fr om your co mputer system before b eginning installation. Remove computer co ver and faceplate if required.
5 Audio Cable (optional) - If you have a sound card and speakers, and would like t o play audio CDs on your computer, you will need to install a CD/DVD audio ca ble. Toshiba's Combo drives use a sta ndard 4-pin audio cable that can be purchased from mo st local computer suppliers.
6 USING THE D VD Combo Drive – SD-R1312 Drive Operation Inserting a Disc - Horizontally To insert a disc into a drive that is moun ted horizont ally, perform the following steps: Figure 1.Inserting Disc 1. Open the drive's L oading tra y b y pressing the Eject Button.
7 Figure 2.Inserting Disc Vertically Removing a Disc To remove a disc from the Combo drive, perform the following steps: 1. Open the Loading T r a y by pressing the Eject Button. 2. Slide disc holders a wa y from disc. 3. Grasp disc by edges , and lift out of loading tra y .
8 Emergency Ejection CAUTION: The following procedure is intended on ly as a last resort when pressing the eject button fails to open the Loading Tray 1. T ur n computer powe r OFF by properly shutting down system. 2. Inser t a solid bar (i.e. large paper clip) into Emergency Eject hol e and push in until loading t ra y opens.
9 TR OUBLESHOO TING – SD-R1312 Problem Solution Disc tra y cannot be opened • Check that there is pow er to drive. • Use Emergency Eject instructi ons to open tray . Drive is not recognized by system • Is the drive connected proper ly? Are all cables plugged in proper ly (e.
10 SPECIFICA TIONS – SD-R1312 General Interface: ATAPI Applicable Formats - Write: Formats for Writing Disc at once, Track at once , session at once, Packet Write, increm ental write, restri cted ov.
11 CD-R (Write) 5,940 – 6,800r pm (12/16/20/24/32X ZCL V) 5,100 – 5,940rpm (12/15/20/24X ZCL V) 2,550 – 5,940rpm (12X CL V) 850 – 1,980prm (4X CL V) High Speed CD-R W (Write) 2,125 – 4,950rp.
12 Relativ e Humidity Operating 8% to 80% Storage/Shipping 5% to 95% (wet bulb 40° C ma x) Vibration Operating (5 to 500 Hz) (re ad) 2.45 m/s 2 (0.25G) (O-P) Operating (5 to 500 Hz) (wr ite) 2.45 m/s 2 (0.25G) (O-P ) Non-operatin g (10 to 500Hz) 9.8 m/s 2 (1.
13 DRIVE CONNECT ORS – SD-R1312 Figure 1.SD-R1312 Combo Drive Rear Panel - Connectors Power Connector Power is supplied to your DVD d rive by the connection with your computer's +5V/+12V power cable to the power socket at the back of dri ve.
14 Table 1.Interface Pin Assignments INTERFACE PIN ASSIGNMENT PIN NO . I/O SIGNAL NAME HOST SIGNAL NAME PIN NO . I/O SIGNAL NAME HOST SIGNAL NAME 1 I Reset Host Reset 21 O HDRQ DMA Request 2 - GND 22 .
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Toshiba SD-R1312 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Toshiba SD-R1312 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Toshiba SD-R1312 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Toshiba SD-R1312 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Toshiba SD-R1312, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Toshiba SD-R1312.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Toshiba SD-R1312. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Toshiba SD-R1312 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.