Manuale d’uso / di manutenzione del prodotto 38282 del fabbricante Toro
Vai alla pagina of 20
Form No. 3369-487 Rev B Power Clear 418 ZR/ZE Snowthrower Model No. 38272—Serial No. 312000001 and Up Model No. 38282—Serial No. 312000001 and Up Operator's Manual Introduction This machine is intended to be used by residential homeowners.
T raining • R ead, understand, and follo w all instructions on the machine and in the man ual(s) before operating this machine . Be thoroughly familiar with the controls and the proper use of the mac hine. Know ho w to stop the mac hine and disengage the controls quic kly .
• Disengag e po wer to the rotor blades when mac hine is transported or not in use . • Never operate the mac hine without good visibility or light. Alwa ys be sure of y our footing, and keep a r m hold on the handles . W alk; nev er run. • Never touch a hot engine or m ufer .
Safety and Instructional Decals Important: Safety and instruction decals are located near areas of potential danger . Replace damaged decals. 1 17-6047 1.
Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Qty . Use Oval-head bolts 2 Curved washers 2 1 Handle knobs 2 Install the handle. 2 No parts required – Install the recoil starter handle. Discharge chute assembly 1 Screws 2 W ashers 2 Locknuts 2 3 Knob 1 Install the discharge chute assembly .
2 Installing the Recoil Starter Handle No Parts Required Procedure Install the recoil starter handle in the rope guide as shown in Figure 4. Figure 4 1.
Figure 6 1. Mov e the mac hine to a lev el surface . 2. Clean around the oil ll cap (Figure 11). 3. Unscrew the oil ll cap and remo v e it. 4. Slowly pour oil into the oil ll hole .
Note: Ensure that a gap of 1/16 to 1/8 inc h (2 to 3 mm) exists between the control bar and the handle (Figure 8). Important: The control ca ble must contain some slack when y ou disengage the control bar for the rotor blades to stop proper ly . Adjusting the Control Cable 1.
Operation Note: Deter mine the left and right sides of the machine from the normal operating position. DANGER Gasoline is extremely amma ble and explosi v e.
Important: Do not tip the machine all the w ay forward onto its nose, or fuel may leak out of the machine. Max ll: 12 oz. (0.35 l), type: automoti ve detergent oil with an API ser vice classication of SJ , SL, or higher .
Figure 17 Note: R emov e y our glov e when y ou push in the primer so that air cannot escape from the primer hole. Important: Do not use the primer or the chok e if the engine has been r unning and is hot. Excessi v e priming may ood the engine and prevent it from starting .
Engaging the Rotor Blades T o engage the rotor blades , hold the control bar against the handle (Figure 20). Figure 20 1. Control bar Disengaging the Rotor Blades T o disengage the rotor blades , release the control bar (Figure 21).
Figure 24 1. T rigger 2. Chute deector Clearing a Clogged Discharge Chute Important: Hand contact with the rotating rotor blades inside the discharge chute is the most common cause of injur y associated with machine. Never use y our hand to clean out the discharge chute.
Maintenance Note: Deter mine the left and right sides of the mac hine from the nor mal operating position. Recommended Maintenance Schedule(s) Maintenance Service Interval Maintenance Procedure After the rst hour • Check the control cable and adjust it if necessary .
3. Place an oil drain pan under the oil drain plug (Figure 11), remo v e the oil drain plug, and tip the machine backw ard (handle do wn) halfw ay to the g round to drain the used oil into the oil drain pan. Important: Do not tip the machine all the w ay back to the ground, or fuel may leak out of the machine.
Figure 29 1. Center electrode insulator 3. Air gap (not to scale) 2. Side electrode 6. Install the spark plug and tor que it to 20–22 ft-lb (27–30 N-m). 7. Connect the wire to the spark plug . Replacing the Drive Belt If driv e belt becomes w orn, oil-soaked, ex cessiv ely crack ed, frayed, or otherwise damaged, replace the belt.
Important: Ensure that y ou install the drive belt so that it sits abov e the two ta bs on the idler ar m and below the idler ar m brak e (Figure 31). 7. Install the driv e belt co v er with the fasteners that you remov ed in step 1. Storage Storing the Machine W ARNING • Gasoline fumes are highly ammable, explosive, and dangerous if inhaled.
Notes: 18.
Federal Emission Control W arranty Statement A T wo-Y ear Limited W arranty Y our Warranty Rights and Obligations The U.S. Environmental Protection Agency (EP A), The T oro Company , and its afliate, T oro W arranty Company , are pleased to explain the emission control system warranty on your 2009 and later utility/lawn/garden equipment engine.
Power Clear 180 Single-Stage Snowthrowers The T oro T otal Coverage Guarantee A T wo-Y ear Full W arranty (45 Day Limited W arranty for Commercial Use) Conditions and Products Covered The T oro Compan.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Toro 38282 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Toro 38282 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Toro 38282 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Toro 38282 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Toro 38282, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Toro 38282.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Toro 38282. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Toro 38282 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
