Manuale d’uso / di manutenzione del prodotto R502 del fabbricante Tenda
Vai alla pagina of 36
Multifunctional Broadban d Router User Guide Copyright S t atement is the registered trademark of Shenzhen T enda T echnology Co., Ltd. Other trademark or trade name mentioned herein are the trademark or registered trademark of above company .
Multifunctional Broadban d Router User Guide Contents Content s ................................................................................1 1.1 Hardware Installation ............................................................ 1 1.2 LED Indicators on Rear Pan el .
Multifunctional Broadban d Router User Guide Chapter One Hardware Inst allation Rear Panel Port Deta ils 4 10/100M LAN Ports Connect to 10/100Base-T Ethernet LAN Car ds or Uplink to Switch/Hub RESET W arning! When you press “RESET” up to 7 seconds, your configuration will be lost and the router restores to factory default settings.
Multifunctional Broadban d Router User Guide 1.2 LED Indicators on Rear Panel LED Indicators Det ails POWER Indicates the status of the Power SYS Blinking Indicates the device’s system goes well. W AN Blinking Indicates the W AN port is transmitting or receiving data.
Multifunctional Broadban d Router User Guide Chapter Two Configuration Guide 2.1 T o configure the netw ork on your PC correctly 1. Please click “My Network Places” on your desktop and select “Properties”. 2 . Please right-click “Local Area Connection” and selec t “Properties”.
Multifunctional Broadban d Router User Guide 4. On this page, there are two options for IP settings : “Obtain an IP address automatically(O)” and “Use the following IP address(S)” A ： If you select “Obtain an IP address automatically(O)”, please refer to the figure on the right.
Multifunctional Broadban d Router User Guide address, please fill in this blank. After finishing above settings, please click “OK” to submit configuration, and click “OK” in “Local Area connection” to save configuration. 2.2 T o check the connection 1.
Multifunctional Broadban d Router User Guide 2.3 Log in the Router 1. Please open IE and enter “ http://192.168.0.1 ” in the address bar , then press “Enter” 2. Then right Figure will appear to require User name and Password, please enter as per below factory default: User Name: admin Password: admin Then click “OK”.
Multifunctional Broadban d Router User Guide 2.4 Get to Know the Management Interface 1 、 After entering into the configuration Interface, you will see 9 function menus on the left ,including: S tatus, Wizard, Advanced Config, DHCP Server , V irtual Server , Security Setting, Routing Setting, System T ool, Logo ut.
Multifunctional Broadban d Router User Guide 2.5 Quick Inst allation Guide 1 、 Click “Next” when you enter in the “Welcome” interface. 2 、 Please select your Access mode when you enter into Wizard interface. This Router supports 4 kinds of Access modes: Factory default Access mode is “Dynamic IP” A.
Multifunctional Broadban d Router User Guide B. If you select “Ethernet Broadband, automatically obtain an IP from ISP (dynamic IP)”. Please click “Save”.
Multifunctional Broadban d Router User Guide need to fill in one of them. PPTP Account: fill in with your Account provided by your ISP . PPTP Password: fill in with your password provided by your ISP .
Multifunctional Broadban d Router User Guide 2.6 St atus This section will show you the Router ’s running status. The right Figure will sho w the router ’s running status. This page shows the router ’s LAN port status (the router is under default setting) 2.
Multifunctional Broadban d Router User Guide 2.8 Advanced Config LAN Settings This page shows you the detailed settings for LAN ports. 1.MAC Address This is router ’s MAC address that you can not change. 2.IP Address: 1 92.168.0.1 is the Router ’s current IP Address and Factory default IP Address.
Multifunctional Broadban d Router User Guide WEB Management Interface so that you can successfully access to the Internet. Moreover , the default gateway of all the computers under this router is required to set as this IP address. W AN Setting This page shows you the detailed Settings for W AN(PPPoE).
Multifunctional Broadban d Router User Guide Connect Automatically , Connect after S tart and Break off. Manual connect, connect by user . Connect when needed, Connect automatically when data access.
Multifunctional Broadban d Router User Guide clear how to fill, you are suggested to use this function. For example, you may cha nge the W AN port to 00:00:56:76: CC: A1 as setting on the right. DNS DNS (Domain Name System service) Server distributes Domain name addr ess and IP address for internet host.
Multifunctional Broadban d Router User Guide 2.9 DHCP Server DHCP Server DHCP (Dynamic Host Configure Protocol) can distribute IP address, Subnet mask, Gateway , DNS Server IP Address an d WINS IP Address to clients automatically .
Multifunctional Broadban d Router User Guide 2.10 Virtual Server Virtual Server 1. Service Port: The service port which the router offers to WA N . 2. IP Address: The IP Address of the computer in the LAN which work as a virtual server . 3. Enable: Please select “Enable” and the rules will go into effect.
Multifunctional Broadban d Router User Guide Note: If you configure a virtual server (server port: 80), you should configure the remo te WEB management in “Wireless Security Configure” as a value different from 80. For example, you coul d set it as 8080.
Multifunctional Broadban d Router User Guide At first you input the IP Address of the LAN computer that is set as DMZ Host in the DMZ Host‘s IP Address bar . Then you select the “start”. Finally click and save all the DMZ Host settings. For example: set a computer with IP address 192.
Multifunctional Broadban d Router User Guide on UPnP protocol, the Host in the LAN can ask the router for a especial port conversion, which enables the external Host to access the resource of the internal Host when necessary .
Multifunctional Broadban d Router User Guide 2.1 1 Security Setting Client Filter T o benefit your further management to the computers in the LAN, you can control some ports access to Internet by data packet filter function. 1. Click “Prohibit Only” or “Permit Only”.
Multifunctional Broadban d Router User Guide set a range of IP addresses. 5. T ype: Selec t the protocol of data packet controlled (All means TCP/ UDP both included). 6. T ime: Please fill in th e time when this rule goes into effect and goes out of effect.
Multifunctional Broadban d Router User Guide 1. Enable URL Filter F unction 2. Filter Mode: T wo filter modes, “Prohibit Only” and “Permit Only”, are available. W hen you select “Prohibit Only”, you are a ble to forbid the computer with the IP address visiting the URL with the contents stated.
Multifunctional Broadban d Router User Guide Note: Y ou should rest art your client utility , or run “net stop dnscache” in its MS-DOS window to make the setting go into effect due to the DNS cache function of Window s.
Multifunctional Broadban d Router User Guide description of this computer with this MAC address. 5. Action: Click “ADD” to add the MAC Address in the MAC address column.
Multifunctional Broadban d Router User Guide Remote Web Management This section sets the web management port and IP address of computer which can execute remote web management in the WA N ; 1. Enable: Enable remote W EB manager function. 2. IP Address: The IP address in W AN which is allo wed to execute remote WEB managing function.
Multifunctional Broadban d Router User Guide the computers in W AN is able to log in and execute remote WEB manager function. If you change this default IP (take 218.88.93.33 for example), only the compute with IP of 218.88.93.33 is able to log in and execute this function.
Multifunctional Broadban d Router User Guide 2.12 Routing Setting Route T able System routing table is a table of the router that owns the fixed route which is set by the system in advance. Generally speaking, it is configured after starting the system.
Multifunctional Broadban d Router User Guide 2.13 System T ool Time Setting This section is to set system time of router . Y ou would set your own time or obtain GMT time from Internet. Note: After you turn off the pow er of the router , the time information would be lost.
Multifunctional Broadban d Router User Guide but all the IP are fixed, one or more. Whereas the IP of DDNS is fluctuant and stochastic. Backup/Restore Here you may backup the setting currently or resume the former router setting. Method Of Backuping The Setting: Click the button of “backup” and a dialog box will appear .
Multifunctional Broadban d Router User Guide Step s Of Sof tware Upgrade 1 、 Please login our company website( www . tenda.cn ) befor e upgrade, and do wnload the newer edition software. 2 、 Please decompress the upgrade file do wnloaded by using the WinRAR software.
Multifunctional Broadban d Router User Guide Default IP address ： 192.168.0.1 Default Subnet Mask: 255.255.255.0 Notice : After restoring factory setting, it will not take ef fect until you reboot the router .
Multifunctional Broadban d Router User Guide For example ： we change th e Username a nd Pa ssword into: Username tenda Password tenda Then you need to input your parameter information according to the figure on the right. Notice : Considering the securit y , we strongly recomm end that you change the initial Username a nd Password.
Multifunctional Broadban d Router User Guide Package Content s Please unpack the packaging carefully and you would be able to find the following articles included: Article Quantit y Multifunctional br.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Tenda R502 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Tenda R502 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Tenda R502 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Tenda R502 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Tenda R502, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Tenda R502.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Tenda R502. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Tenda R502 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
