Manuale d’uso / di manutenzione del prodotto SX3e del fabbricante Telular
Vai alla pagina of 26
P HONECELL ® SX3e AMPS F IXED W IRELESS T ERMINAL U SER M ANUAL Total communications freedom at your fingertips...voice/fax/data. 06/25/01 Part No. 56017302.
Thank you for choosing the Phonecell SX3 Fixed Wireless T erminal from T elular . This innovative product lets you connect up to five pieces of standard telephone equipment into a cellular network for total communications flexibility . Please follow this guide to unpack, set up and operate your new Phonecell safely and properly.
P HONECELL SX3e AMPS 3 U SER M ANUAL T able of Contents Introduction ...............................................................................................2 T echnical Support ..................................................................
P HONECELL SX3e AMPS 4 U SER M ANUAL Getting S tarted... Pre-Inst allation Checklist Before attempting Phonecell SX3e installation, make sure you have the following components, tools and materials.
Installation Summary P HONECELL SX3e AMPS 5 U SER M ANUAL S tep 1. Choose an Antenna Location (pg. 6-7) • • Choose a location. • • Next, connect power to the FWT and turn the unit ON. • • Then, connect the antenna (not supplied) . • • Check the cellular signal strength and move the antenna until you achieve the best signal possible.
P HONECELL SX3e AMPS 6 U SER M ANUAL S tep 1. Choose an Antenna Location Y our Phonecell SX3 receives operating commands from the cellular network and relies upon signal strength for proper operation. Therefore, finding an antenna location with good signal strength is critical for call quality .
P HONECELL SX3e AMPS 7 U SER M ANUAL WARNING! Never operate your Phonecell when any person is within 16 inches (40 cm) of the antenna. How to Connect the Antenna: 1) Connect the Power Supply to the DC “PWR” port on the back of the Phonecell – see Figure 3.
P HONECELL SX3e AMPS 8 U SER M ANUAL S tep 2. Plug In Y our T elephone Connect Y our Telephone: 1) Locate the modular (RJ-1 1) line port on your phone and plug in one end of a standard (RJ-1 1) phone cord. 2) Connect the other end of the cord to the RJ-1 1 port on the back of your Phonecell SX3e – see Fig.
P HONECELL SX3e AMPS 9 U SER M ANUAL S tep 3. NAM/Phone Number Setup Y ou can program the Phonecell SX3 with an ordinary tone-dial (DTMF) telephone, which is sometimes referred to as a POTS (Plain Old T elephone Service) phone. NOTE: this programming mode is not accessible while you're in a call.
P HONECELL SX3e AMPS 10 U SER M ANUAL NOTE: The following NAM Parameters are automatically set by the SID value in S tep #4 on the previous page. These step s (5–7) are only needed if you want to override the standard AMPS settings listed on the previous page.
Step #6 - How to Override the Number of Dedicated Control Channels. Press: # * 26 * _ _ # The spaces represent your 2-digit range of Dedicated Control Channels. When you first turn on the Phonecell, it automatically scans up to 21 control channels looking for your cellular provider .
P HONECELL SX3e AMPS 12 U SER M ANUAL S tep 4. Install Y our Phonecell 4a. W all-Mount Instructions: 1) Hold the mounting bracket against the wall and mark two holes for the long mounting screws –see Fig. 8. 2) Remove the bracket and drill two holes for the long mounting screws –see Figure 9.
P HONECELL SX3e AMPS 13 U SER M ANUAL IMPORT ANT! Y our Phonecell SX3 must be placed or mounted on a flat, level surface to allow proper ventilation. Do not block the air vents or the space beneath your Phonecell as this could cause the unit to overheat and fail.
P HONECELL SX3e AMPS 14 U SER M ANUAL Phonecell Operation LED Status T able LED Color LED Activity Description RED Flashing Malfunction. Hardware fault detected RED Continuous No cellular service YELL.
P HONECELL SX3e AMPS 15 U SER M ANUAL Phonecell Operation – Continued Import ant T ones and Alerts No-Service T one – When cellular service is not available, the receiver emits a No-Service (fast-beeping) tone instead of the normal (steady) dial tone.
P HONECELL SX3e AMPS 16 U SER M ANUAL V ariable Dial T ime (Auto SEND Delay) Option When you place a call, your Phonecell SX3 automatically sends the phone number over the cellular network after you dial the last digit – just like a landline phone.
P HONECELL SX3e AMPS 17 U SER M ANUAL Three-W ay Conference Calls - For three-way conference calls, the Out-of-Band Signaling option must be enabled. Pressing the HOOKFLASH function transmits the SEND command. Please see the Data After SEND option below .
P HONECELL SX3e AMPS 18 U SER M ANUAL Phonecell SX3 T r oubleshooting T elephone Service is Not Working If the telephone service is not working, first check the operation of the telephone equipment and wiring connected to your Phonecell SX3 .
P HONECELL SX3e AMPS 19 U SER M ANUAL Y our Phonecell SX3 FWT (Fixed Wireless T erminal) functions as both a radio transmitter and receiver . When it is ON, the FWT receives and sends out radio frequency (RF) energy . The unit may operate in frequency ranges between 824 MHz and 894 MHz.
P HONECELL SX3eAMPS 20 U SER M ANUAL Safety Information – Continued Driving Check the laws and regulations on the use of cellular products in the areas where you drive. Some jurisdictions prohibit your using a cellular device while driving a vehicle.
P HONECELL SX3e AMPS 21 U SER M ANUAL Safety Information – Continued Potentially Explosive Atmospheres T urn your Phonecell SX3 OFF when in any area with a potentially explosive atmosphere. It is rare, but your Phonecell SX3 or its accessories could generate sparks.
P HONECELL SX3e AMPS 22 U SER M ANUAL AMPS T echnician Programming AMPS T echnician Programming Commands The Phonecell SX3 can be programmed on location with an ordinary telephone, which is sometimes referred to as a POTS (Plain Old T elephone Set) phone.
P HONECELL SX3e AMPS 23 U SER M ANUAL How to Set the Access Overload Class (ACCOLC) Use the following key sequence to set the ACCOLC: Press: # * 2 * < ACCOLC > # The < > brackets represent the 2-digit ACCOLC.
P HONECELL SX3e AMPS 24 U SER M ANUAL T echnician Programming Commands – Continued How to Set the Post-Receiver Off-Hook (ROH) Option Use the following key sequence to set the post-ROH option: Press.
How to Enter the Periodic Self T est Option Use the following key sequence to program the periodic self test: Press: # * 76 * <self test interval> # The self test interval is programmed in 1 minute intervals from 1 to 65,535. A value of 0 disables the self test.
Part No. 56017302 ©2001 T elular Corporation.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Telular SX3e è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Telular SX3e - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Telular SX3e imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Telular SX3e ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Telular SX3e, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Telular SX3e.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Telular SX3e. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Telular SX3e insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
