Manuale d’uso / di manutenzione del prodotto SS-1002 del fabbricante Telex
Vai alla pagina of 18
1 9350-7741-000 Rev A, 10/2002 User Instructions Model SS-1002 Single Channel Intercom S peaker S t ation Model SS-2002 T wo Channel Intercom S peaker S t ation Model SS-2002RM T wo Channel Rack Mount.
2 FCC S t atement This equipment uses, and can radiate radio frequency energy that may cause interference to radio com- munications if not installed in accordance with this manual.
3 T able of Content s Intr oduction ............................................................................... 4 Description ................................................................................ 4 Featur es ............................
4 Introduction Thank you for purchasing the Audiocom SS-1002/SS-2002/SS-2002RM Intercom Speaker Station. W e hope the many design features of this product will satisfy your intercommunication requirements for many years to come.
5 Figure 1 - SS-1002 / SS-2002 features. Figure 2 - SS-2002RM features..
6 Inst allation Unp acking Each SS-1002 / SS-2002 / SS-2002RM is supplied with the following items. Contact the shipper or your Audiocom dealer immediately if anything is damaged or missing. Be sure to fill out and return the product registration card to T elex to properl y register your intercom station.
7 Mic Kill Receive Audiocom master stations, such as the US-2002A, can transmit an inaudible signal to turn off the microphones in all remote intercom stations on an intercom channel. This is useful when a remote intercom station has been left unattended with the microphone on.
8 Headset Connector Notes If you are using a monaural, dynamic-mic headset, or a monaural, telephone-style, dynamic-mic handset, or a handheld dynamic microphone, plug it into the Headset connector .
9 intercom stations may be reduced. Generally , if intercom stations are within a few hundred feet from the system power supply , phantom power will be suf ficient. Also note that increasing the number of stations will reduce the overall operating distance.
10 All Locally P owered Inter com Stations (Dry Lines) If intercom stations are widely distributed, you can dispense with a system power supply (PS2001L, SPS-2001, etc.) and use local power for each station. When no power is delivered on the intercom channels, this is known as dry-line operation.
11 Figure 9 - Audiocom mode connections for an SS1002 Intercom S tation in a “U” box. Note: for Clear-Com connection, use the Unbal anced Mode Intercom Channel pin-out information listed in the Specifications section.
12 Figure 10 - Audiocom mode connections for an SS2002 Intercom S tation in a “U” box. Note: for Clear-Com connection, use the Unba lanced Mode Intercom Channel pin-out information listed in the Specifications section.
13 Figure 1 1 - Audiocom cable wiring diagrams..
14 Power-Up Make sure any local power supplies are plugged in, then turn on the power switches of any phantom power supplies (PS- 2001L, SPS-2001, etc.) Sidetone Adjustment The SS-1002, SS-2002, and SS-2002RM use full-duplex audio (the same as conventional telephone lines) in which the talk and listen audio are sent and received on the same wires.
15 Operation Channel Select (SS-2002 & SS-2002RM Only) T ap the Ch Select key to select channel 1 or 2. The key is green when channel 1 is selected and red when channel two is selected. Headset/Headphone/S peaker/Microphone Selection • T o use a headset or telephone style handset, set the Speaker and Panel Mic keys to off.
16 S pecifications General Power Requir ements: Phantom Power: +24 VDC nominal, 175 mA Local Power: +12 to +15 VDC, 250 mA Dimensions: See dimension drawings.
17 Call Signaling: Pin 1 - Common Pin 2 - Local power (+12 to +15 VDC) If needed Pin 3 - Power +30 V DC Pin 4 - Intercom channel 1 audio and DC call signaling Pin 5 - Power +30 V DC Pin 6 - Intercom c.
18 TRADEMARKS Audiocom ® is a registered trademark of T elex Comm unications. Names of other products mentioned herein are used for identification purposes only and may be trademarks and/or registered trademarks of their respectiv e companies. W ARRANTY INFORMA TION Products are warranted b y T elex Comm unications, Inc.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Telex SS-1002 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Telex SS-1002 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Telex SS-1002 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Telex SS-1002 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Telex SS-1002, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Telex SS-1002.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Telex SS-1002. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Telex SS-1002 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
