Manuale d’uso / di manutenzione del prodotto W18 del fabbricante Barco
Vai alla pagina of 341
HDX se r ie s User and Instal lat ion manual For HDX , HDX W12, HDX W14,HDX W18 and HDX W20 R5905032/14 02/03/2015.
Product revision Software versi on: 1.9. Barc o nv Noordlaan 5, B-8 520 Kuurne Phone: +32 56.36.82.11 Fax: +32 56.36.883.86 Support: www.barco.com/esupport Visit us at the web: www.
Changes Barco provides this manual ’as is’ without warranty of any kind, either expressed or implied, including but not limited to the implied war- ranties or merchantability and fi tness for a particular purpose.
.
Tabl e of c ont ent s T ABLE OF C ONTENTS 1 . S a f e t y .... ...... .... .... .... .... ...... .... .... .... .... .... ...... .... .... .... .... ...... .... .... .... .... .... ...... .... ... 7 1.1 General considerations .........................
Tabl e of c ont ent s 7 . 8 H e l p i n f o r m a t i o n i n a d j u s t m e n t m o d e................................... ............... ............... ............... ............. .. 7 4 8 . I n p u t ..... .... .... .... ...... .... .... .... .
Tabl e of c ont ent s 10.4.3 PiP window , source selection .............. ............... ....................... ............... ............... .............. 1 4 1 10.4.4 PiP window, S ize .......................... ............... ............... .
Tabl e of c ont ent s 1 2 . 1 6 H i g h E n d S y s t e m s M i r r o r ......................... ............... ............... ....................... ............... ......... ..... 2 1 6 1 3 . P r o j e c t o r C o n t r o l . ...... ...... .....
Tabl e of c ont ent s 15.2 Cleaning the exterior of t he projector .................... ............... ...................... ............... ............... ....... 2 9 1 1 6 . S e r v i c i n g........ ...... .... .... .... .... ...... .... .... ..
Tabl e of c ont ent s 6 R5905032 HDX SERIES 02/03/2015.
1. Safety 1. SAFETY About this chapter Read this chapter at tentively . It contains im portant i nformation to prevent personal injury while installing and using a HD X projector . Furthermore, it incl udes several cauti ons to prevent damage to t he HDX projector .
1. Safety the potential risk to themselves or other persons. T he term USER and OP ERA TOR refers to any person other than SERVICE PER - SONNEL, AUTHOR IZED to operate profes sional project ion systems.
1. Safety • It is hazardous to op erate without lens or shield. Lenses, shields or ultra violet screens shall be changed if they have become visibly damaged to such an extent that their ef fectiveness is impaired. Fo r example by cracks or deep scratches.
1. Safety • Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a dam p cloth for cleaning. Never use strong solvents, such as thinner or benzine, or abrasive cleaners, since these will damage the cabinet.
1. Safety RA TH PR RZ HD SW 1m SW SW SW HD SH RA TH RZ SH (B) TOP VIEW (A) SIDE VIEW Image 1-1 AS i d e v i e w . B T op view . RA Restricted Access locat ion (boot ar ea of project or). PR Project or . TH Theat er . RZ Restriction Zo ne in the theater .
1. Safety HDX projector Hazard Dist ance HD [m] TR 0 1 2 3 4 5 6 7 8 0,5 1,0 1,5 2,0 2,5 3,0 3,5 4,0 4,5 5,0 5,5 6,0 6,5 7,0 7,5 8,0 8,5 9,0 10,0 Image 1-3 HD (in meter) i n function of t he Throw Ratio (T R) 1.
2. Gener al 2. GENERAL About this chapter Read this chapter before installing your HDX projector . It contains important infor mation concerning installation requirements for the HDX projector , suc h.
2. Gener al particl es in the environment of the projector . The m anufacturer reserves the right t o refuse repair if a proj ector has been subject to knowingly neglect, abandon or improper use. Main Power requirements The HDX projector operat es from a nominal mono phase power net with a separate earth ground PE.
2. Gener al Image 2-2 Remove carton and foam rub ber 3. T ake out the foam rubber . 4. T ake out t he projector . Save the original shipping carton and packing material, they will be necessary if you ever have to ship your projector . For maximu m protection, repack your projector as it was originall y packed at the factory .
2. Gener al One xeno n lamp i s mount ed ins ide t he lamp house at d eli very . The pr oject or le nses a re not include d in t he package of the projector .
2. Gener al F/C AUDIENCE F/T FLOOR SCREEN Image 2-4 Front pr ojection F/C AUDIENCE FLOOR SCREEN Image 2-5 Front pr ojection, Ceilin g m ounted, in ta ble posit ion Rear projection The projector is installed, either in a table mount or ceiling mount con fi guration, at the other side of the screen opposite the audience.
2. Gener al AUDIENCE BACKST AGE R/C FLOOR SCREEN Image 2-7 Rear proj ection, c eiling moun ted in tab le posit ion Positionin g the projector FLOOR SCREEN SCREEN PD A CD SCREEN SW SW SH B SH B CD Image 2-8 Pos ition ing proj ecto r The projector should be installed at right angles (horizontally and vertically) to the screen at a distance PD.
2. Gener al Shift range The lens can be shifted with respect to the DMD (P) which result in a shifted image on the screen (Off-Axis). A 100% shift means that the centre point of the projected image is shifted by half the screen si ze.
2. Gener al C Tilting allo wed but l amp fl icker possible Projector lamp will not start up when out of tilt range due to build-in tilt sensor . 2.6 Projector air inlets and outlets Air inlets and outlets Image 2-1 1 The HDX projector has 3 air inlet channels and 3 air outlets.
2. Gener al 1. G o to my .barco.com on ht tps: my .bar co.c om . 2. Login on my .barco.com. If you are not yet registered click on S ign up for my .barc o.com and follow the instructions. With the created login and pas s- word, it is possible to enter the my .
2. Gener al 22 R5905032 HDX SERIES 02/03/2015.
3. Ph ysical ins tallat ion 3. PHYSICAL INST ALLA TION About this projector This chapter describes how the mechanical set up of t he projector has to be done and how t o realize the electr ical connections.
3. Ph ysical ins tallat ion How to install the batteries in the remote control ? 1. Push the battery cover tab with t he fi ngernail a li ttle backwards (1) and pull, at t he same time, the cover upwards (2). 1 2 Image 3-2 2. Insert the two AA size batter ies, making sure the polariti es match the + and - marks inside the battery c ompartment.
3. Ph ysical ins tallat ion Image 3-5 3.1.3 RCU XLR ada ptor installation Install the rugged case before installing the XLR ad aptor . Vice-versa, remove the XLR ad aptor before remo ving the rugge d case fro m the RCU. Necessary t ools 5m m fl at s crew driver.
3. Ph ysical ins tallat ion Image 3-7 3.1.5 RCU usa ge possibilit ies Summarized p ossibilities Ref. Possibili ty descriptio n Comment a. RCU not wired b. RCU wired (mini-jack) Backlight illuminates continuously when wire i s connected. Infra red disabled.
3. Ph ysical ins tallat ion 3.2 Le nses Overview • Available lenses • Lens selection • Lens installation • Lens removal • Lens safety cable • Lens shift, zoom & focus • Scheimp fl ug adjustment 3.
3. Ph ysical ins tallat ion Image 3-18 R9862010 : TLD+ zoom lens (1.5 - 2.0 : 1 ) Image 3-19 R9862020 : TLD+ zoom lens (2.0 - 2.8 : 1) Image 3-20 R9862030 : TLD+ zoom lens (2.8 - 4 .5 : 1) Image 3-21 R9862040 : TLD+ zoom lens (4.5 - 7.5 : 1 ) Image 3-22 R9829997 : TLD+ zoom lens (7.
3. Ph ysical ins tallat ion Image 3-23 Lens calc ulator The Lens Calculator can also be u sed to determine the position of the projector when the lens type and screen widt h is known. Due to lens tolerances the results of calculated values may b e different from measured va lues.
3. Ph ysical ins tallat ion 4. Ensure that the lens holder stands in the O n-Axis position (horizontal and vertical mid position). Note: The lens holder is placed default in t he On-Axis position at f actory . 5. Gently insert the lens in such a way that the lens connector matches the socket (B).
3. Ph ysical ins tallat ion Image 3-27 Lens removal , unlock 2. Gently pull the lens out of the lens holder . Image 3-28 Lens removal It’ s reco mmended to place the Len s caps of the original Lens p ackaging, back on both side s of the removed Lens to prot ect the opt ics of th e Lens.
3. Ph ysical ins tallat ion 1 2 3 3 Image 3-29 Lens safet y cable 1 Lens motor block 2 Mounting fl ange 3C l a m p 2. Insert both cable sides into the c lamp; Strap the cable and make sure that the clamp is positioned on 45° from the bottom to avoid interference of the cable with the lens locking mechanism.
3. Ph ysical ins tallat ion Image 3-31 3.2.6 Lens shift, zoom & focus Via Lens key 1. Press LENS key on the local keypad or the remote control. The zoom/focus menu opens. Image 3-32 Zoom/Focus adj ustment 2. Use the ▲ or ▼ key to zoom the lens.
3. Ph ysical ins tallat ion Image 3-33 Shift ad justment 3. Use the ▲ or ▼ ke y to shift the lens in vertical direction. Use t he ◄ or ► key t o shift the lens in horizontal direction. Pres s ENTER to switch to zoom/focus adjustment. Via direct access keys o n the remote contro l 1.
3. Ph ysical ins tallat ion Sche imp fl ug adjustment points 4 1 2 3 d D c C A a B b Image 3-35 Scheimp fl ug a djustme nts Indic atio n on draw ing Funct ion 4 Locking nut 1, 2 and 3 Scheimp fl ug adjustment nuts A, B, C and D Set sc rews a, b, c and d lock nuts 1, 2 and 3 are adjustment points.
3. Ph ysical ins tallat ion 5. Optimize the focus of the projected im age as follows: a) P lace t he zoom lens in TELE position (smallest projected image) and adjust the f ocus using the lens focus barr el or motorized focus control.
3. Ph ysical ins tallat ion 2 F Image 3-39 Right bott om focusin g 8. Sharpen top right corner of the screen by adjusting nut 3 3 F Image 3-40 Corner f ocusing 9. Repeat from step 6 until the projected focus pattern is as s harp as possible in t he center , left, right, top and bot tom of the screen.
3. Ph ysical ins tallat ion 1/3 to 1/2 Image 3-41 4. Fasten lock nut d. 5. Tight en nut 4 until the offs et of the image movem ent created in step 3 is canceled. Tip : The amount of i mage movement in step 3 will determine how tight the nut in step 5 will need t o be turned t o return the image to its original p osition.
3. Ph ysical ins tallat ion 4. Connect the male side of the power cord to t he local power net. Caution: Ensure that t he power net meets the power requirements of the projector . W ARNING : Do not attempt operation i f the AC s upply a nd co rd are not wit hin the speci fi ed voltage and power range.
3. Ph ysical ins tallat ion How to mount 1. Turn the pr ojector upside down. 2. Turn out the 4 feet. Image 3-45 Remove feet 3. Turn out the f eet of the carry handle as far as possible. Image 3-46 Mount carry h andle 4. Place the carry handle on the proj ector as illustrated.
3. Ph ysical ins tallat ion 1 2 Image 3-47 Insert bolts 3.6 Mounting the top carry handler Purpos e This carry handle can be used to transport the pr ojector in an eas y way . Necessary t ools 8 mm A llen wrench Necessary p arts • 4x bolt M10 x 16 • 4x was her • 1x carry handler How to mount 1.
3. Ph ysical ins tallat ion 3.7 Suspens ion of the projector with rigging clamps Rigging points and rigging cl amps When a carrying handle is mounted at the bottom side of the projector , eight slots ar e available to mount rigging clamps. Four slots are longitudinally (1) oriented and four slots ar e transversely (2) or iented.
3. Ph ysical ins tallat ion 3. Turn in the rigging clamps into the rigging points using a 17 mm open ended spanner and secure the rigging cl amps by turning the safety nut on the rigging clamp against the rigging point using a 17 mm open en ded spanner .
3. Ph ysical ins tallat ion 7. Lock all four rigging clamps by turning the fi xat ion handle clockwise. Image 3-54 Clamp fi xation 8. Install the 2 safety cables , one on both sides of the carry ing handle, and around the truss.
3. Ph ysical ins tallat ion Skew Image 3-56 Skew adju stment Tilt adjustment with the clamps 1. Adjust both front side clamp or both back side clamps to adjust the tilting. Always adjust by two to avoid deformation of the frame. 2. Loosen the security nut on both c lamps.
3. Ph ysical ins tallat ion 46 R5905032 HDX SERIES 02/03/2015.
4. Input & Co mmun i cati on 4. INPUT & COMMUNICA TION Overview • Introduction • Input s ource connections • Com munication connections • U tility-Accessory O utlet 4.
4. Input & C ommuni cation 4.2 Input source connections DVI and 3G/HDSDI input This input module is standard deli vered with the HDX projector . DUAL LINK DVI-I HDCP INPUT SEL SYNC 3G/DUAL HDSDI O.
4. Input & Co mmun i cati on • Data and HD sources RGB and Y UV [HS/VS, CS or SOG(Y)]: - Pixel clock maximum 210 M Hz - 8 bit digital output • Video sources CVB S, S-VIDEO, RG B and YUV [CS, CV or SOG (Y)]: - P AL B/D/I /G/ H, P AL60, P AL M, P AL N, P AL Nc - NTSC M/J, NTS C 4.
4. Input & C ommuni cation • HDMI (High-De fi nition Multimedia Interface) HDMI 1.4a up to 210MHz pixel clock. Support for ‘Deep Color’ up to 12 bit per color . • DisplayPort DisplayPort 1.1a up to 210 MHz pixel clock. Support for ‘Deep Color’ up to 12 bit per color .
4. Input & Co mmun i cati on Pin Description 2 Cold 3H o t 4 Return - (or not used) 5 Return + (or not used) DMX DMX-512 Lighting protocol over RS-485 interface. Carries information of 512 channels from a lighting con tr oller to lighting devices.
4. Input & C ommuni cation RS232 An Electronic Industri es Association (EIA) s erial digital interface standard s pecifying the c haracteristics of the commu- nication path between two devices using either D-SUB 9 pi ns or D-SUB 25 pins connector s.
4. Input & Co mmun i cati on Functi on Co lor Descrip tion PWR orange See chapter “ Getting start ed ”, topic “ Status LEDs ” LMP orange See cha pter “ Gett ing start ed ”, topic “ Status LEDs ” 4.4 Utilit y-Accessory Out let What can be done ? An extra DMX controlled accessory can be added to projector .
4. Input & C ommuni cation 54 R5905032 HDX SERIES 02/03/2015.
5. Getti ng started 5. GETTING ST ARTED Overview • RCU & Local keypad • T erminology overview • Pow er on projector • Sw itc hing to st andby • Pow er off projector • Status LEDs • Using the RCU • Projector Address • Sou rce selection 5.
5. Get ting s tarted MENU EXIT ENTER PA US E TEXT PHASE TINT COLOR BRIGHTN CONTR 9 0 7 8 5 6 3 4 1 2 LENS LENS ZOOM LENS SHIFT LENS FOCUS SHARPN LENS SHIFT 5 * % 3 $ 7 7 ( 5 1 3 , 3 : , 1 ' 2.
5. Getti ng started Ind. Key name Description 16 TEXT T oggle key to activate or deactivate on s creen text boxes while adjust ing a setting. When adjusting one of the image controls, e. g. during a meeting, the normally displayed bar scale can be deactivated by pressing ’ TEXT’ key fi rst.
5. Get ting s tarted Image 5-3 Start up scr een, Main This screen indicates : - the selected Main i nput - the selected PIP input - the IP address - the Customer Id - the Lamp status - the Mains voltage - the current ambient tem perature - the T ext st atus (OS D) T o display an image, th e standby key must be pressed once.
5. Getti ng started • num ber of Strikes • Run time in h ours • Rem aining run ti me in hours • slide bar indication with percentage indi cation of the current run time, compared with the maximum life time of the lamp.
5. Get ting s tarted MENU EXIT ENTER PAU S E TEXT PHASE TINT COLOR BRIGHTN CONTR 9 0 7 8 5 6 3 4 1 2 LENS LENS ZOOM LENS SHIFT LENS FOCUS SHARPN LENS SHIFT 5 * % 3 $ 7 7 ( 5 1 3 , 3 : , 1 ' 2.
5. Getti ng started C AUTION : Never switch off the projector while the message ’Saving data ... ’ is displayed ! 5.6 Status LED s Overview LED Color sta tus Description Red on Projector is in sta.
5. Get ting s tarted F1 F2 F3 F4 F5 AD J EX IT EN TE R PA US E PH AS E TE XT SH AR PN TI NT CO LO R BR IG HTN CO NTR TR EB LE BA LA NC E BA SS VO L 90 7 8 5 6 34 1 2 Image 5-7 IR control via re fl ective scr een Hardwire d to the XLR i nput 1. Plug one end of the rem ote cable in the connector on the bottom of the RCU.
5. Getti ng started 5.8 Projector Address 5.8.1 Dis playing and P rogramming a ddresses int o the RCU Displaying the Projector Address on th e Screen. 1. Press Address key (recessed key on the RCU) with a pencil . The projector ’ s address is displayed on the loc al LCD screen.
5. Get ting s tarted Source selection when picture in picture is active Use the W indow button on the r emote control or the loc al keypad to s elect the main window or the pic ture in picture (PiP) window .
6. Quick set up adj us tment 6. Q UI CK SET UP ADJ USTME NT Overview • T ext boxes ON or OFF • Quick Lens A djustment via LENS key • Direct Lens Adjustmen t (RCU) • Q uick picture in pictur e • Quick language selection 6.
6. Quick s et up adjustm ent 1 2 3 4 5 6 7 89 0 MENU EXIT ENTER RGB STBY P AUSE TEXT P A TTERN WINDOW PIP LENS AUTO F N MENU EXIT ENTER PA U S E TEXT PHASE LENS 5 * % 3 $ 7 7 ( 5 1 3 , 3 : , 1 ' 2 : $ 8 7 2 , 0 $ * ( 1 1 Image 6-2 Lens button Image 6-3 Zo om/F ocus ad just ment 2.
6. Quick set up adj us tment Image 6-4 Zoom/Focus adj ustment 2. Press ENT ER to go to th e Shi f t menu. Image 6-5 Shift ad justment 3. Use the ▲ or ▼ ke y to shift the lens in vertical direction. Use t he ◄ or ► key t o shift the lens in horizontal direction.
6. Quick s et up adjustm ent CONTR 1 2 LENS ZOO M LENS SHI FT LENS FOC US LENS SHI FT A C B D Image 6-6 Direct lens adj ustment keys AZ o o m B V erti cal shift CF o c u s D Horizontal shi ft 2. Press LENS FOCUS bu tton [- ] or [+] (C) for an overall focus of the image.
6. Quick set up adj us tment MENU EXIT ENTER 5 * % 3 $ 7 7 ( 5 1 3 , 3 : , 1 ' 2 : 1 Image 6-8 Info button The language selection menu is displayed on the screen. Select the desired language wit h the ▲▼ key and press EN TER t o activate.
6. Quick s et up adjustm ent Image 6-10 Main men u Image 6-1 1 Projecto r Control Image 6-12 Change language 70 R5905032 HDX SERIES 02/03/2015.
7. Start up of the a djust ment mode 7. S T ART UP OF THE ADJUST MENT MODE Overview • Abo ut the adjustment mode • Abo ut the us e of the remote control and the local keypad • Start up the adjus.
7. Start up of the a djustmen t mode The main menu of the adjustment m ode opens. Image 7-1 Main me nu 7.4 Navigation and adjustme nts How to na vigate in the me nu structure? On ce in the me nu str uctu re, u se the ▲ or ▼ k ey on the remote control or on the local keypad to s croll through the items in the displayed menu.
7. Start up of the a djust ment mode Use the ◄ or ► key to adjust the current value. The ba r scale will move accord ingly . Press EXIT to fi nalize the adjustment. or , When the bar scale is displayed, via direct input. P ress ENTE R to activate t he input fi eld.
7. Start up of the a djustmen t mode 7.7 T est patterns in adjustment m ode Overview When the adjustment mode is star ted, a test pattern can be called at any moment just by pressing the Pattern key on the RCU or the local key path. Press as many times on the Pattern key as necessary to display the desired test pattern.
8. Inpu t 8. INPUT Overview • Input menu overview • Input Selec tion • Advanced Settings • Input locking • Minim um delay • Native resolution • No Signal •E D I D • 3D input In all cases, the minimum input frequency for 3D is 23 Hz per eye.
8. Input Logo [On/Off] Shutdown [Off/ On] Shutdown time Auto dimming [On/Of f] EDID Con fi gure Create Delete Delete Al l 3D Status Auto Detection Input type Frame sequential - Single channel Frame sequential - Dual channel Frame packing (FHD3D) Side-by-side T op-and-bottom SENS IO ® HI-FI 3D Line Alternating (3G) Second input 8.
8. Inpu t Image 8-3 Select source 8.3 Advanced Settings Overview • Abo ut Input Setup • Input con fi gura t io n • DV I - RGB input • SD I input • 5 cable input • HDM I - DisplayPort input (3 D input module) 8.3.1 About Input Setup Overview Each input module m ust be con fi gured before these module can be used.
8. Input Image 8-6 Advanced set tings, inp ut select ion 8.3.3 DVI - R GB input How to select Select DVI / RGB and press ENTE R to open the selecti ons Image 8-7 DVI selecti on The following selection.
8. Inpu t 8.3.4 SDI input About SDI input The Dual SD/HD/3G-SDI Input can accept standard-de fi nition (SD), high-de fi nition (HD) and 3 Gigabit-de fi ni tion serial-di gital-int er- face (SDI) signals .
8. Input 3G-A and 3G-B: • Direct M apping (3G-A) • Dual HD ( 3G-B) When Dual HD is s elected, it is possi ble to use Swap li nks. If Swap links must be used, use the ▲ or ▼ key to select and press ENTER to accept. The check box will be chec ked.
8. Inpu t 8.4 Input locking What is possible? The output signal can be locked on an internal sync si gnal or on the sync signal of one of the input sources. Or it can follow the input of the Main window or Pip w indow . When locked to the co rresponding input sync, the output will be show n without movement artifacts.
8. Input When Input locking is set to a speci fi c input and there is no sync signal available, the lo cking will be switched to Free run without changing the user settings.
8. Inpu t Image 8-19 Main window Image 8-20 Inp ut, mi nimum d elay 2. Press ENTER to toggle between [On] and [Off ]. [On] : images displayed with minimum delay [Off] : images displayed without minimum de lay 8.
8. Input Sour ce Projected i mage UXGA 4:3 1600x1200 4 :3 1600x1200 image projec ted wit h black borders left and right. WUXGA 16:10 1920x1200 1 6:10 1920x1200 norm al image projected How to toggle to native resolution? 1. Press Menu to activate the menus and select Input → Native Resoluti on [On] .
8. Inpu t Image 8-24 Main window Image 8-25 Input, no signal Image 8-26 No signal, c olor 8.7.2 Background Logo What can be done ? A logo can be switched on or off .
8. Input Image 8-29 No signal, l ogo A dedicated logo can be loaded via Projector T o olset with a HDX plug-in install ed. 8.7.3 Shutdown settings How to change the se ttings 1. Press Menu to activ ate the menus and select Input → No Signal . → Shutdown .
8. Inpu t Image 8-33 Main window Image 8-34 Input, no signal Image 8-35 2. Press ENT ER to toggle between [1] , [3 ] , [5] and [10] minu te s. 8.7.5 Auto Di mming About auto dimming When no s ignal is detected on the selected input the lam p power will be reduced from the current value to its minimum value.
8. Input Image 8-38 No signal, aut o dimming 2. Press ENTER to t oggle between [On] or [Off] . [On] : when no signal, auto dimming is started. [Off] : w hen no si gnal, no auto dimming is started.
8. Inpu t Image 8-39 Main window Image 8-40 Input, EDID Image 8-41 EDID , con fi gure Image 8-42 EDID con fi guration Image 8-43 EDID s election lis t 3. Use the ▲ or ▼ key to selec t the input to con fi gur e. Pres s ENTER to open the selection li st.
8. Input 8.8. 2 Creat e cu stom E DID fi le Descriptio n Y ou can create new custom EDID fi les and enter the desired input timings. How to create 1. Press Menu to activ ate the menus and select I nput → EDID → Create . 2. Press ENTER to open the EDID creation menu.
8. Inpu t 6. Select the Options . If necessary , scroll down to see extra options. Select or clear the check box es. Image 8-48 EDID fi le creati on, optio ns The following options are possible: - Stereo : this c heck box is currently not i n use. Y ou can leave it unchecked.
8. Input Image 8-51 EDID, delete 3. Use the ▲ or ▼ key to select the fi le which must be deleted. Pres s ENTER to delete. Image 8-52 EDID, delete lis t Image 8-53 Con fi rma tion Ac o n fi rmation window o pens. 4. Select Ye s to delete the fi le and press ENTE R .
8. Inpu t Image 8-54 Main window Image 8-55 Input, EDID Image 8-56 Image 8-57 3. Select Ye s to delete all the custom fi le and press ENTER . 8.9 3D input Overview • Abo ut 3D modes •A c t i v a .
8. Input T o activate the s ingle channel 3D mode select: MENU > Input > 3D > Frame Sequential – Single Channel Possible sources: DisplayPort, HDMI, dual-link DVI, 5-cable analog (up to 210 MHz), DVI analog (up to 170 MHz), SDI (up to 150 MHz).
8. Inpu t 1 SENSIO ® Hi-Fi 3D s tr eam 2 Left expansion 3 Right ex pansion 4 SENSIO ® Hi-Fi 3D interpolation 5 SENSIO ® Hi-Fi 3D interpolation 6 Right s tream 7 Left stream SENSIO ® 3D Decoder - FFC is using both the SEN SIO ® 3D Dec oder as well as the SE NSIO ® A utodetec t functionality .
8. Input 2xDVI/2xHDMI/2xDP 1 2xSDI 2 Fpix ≤ 210MHz. Fpix ≤ 150MHz. Max. resolution: 1920x1200@60Hz or 204 8x1080@60Hz. Max. resolution: 1920x1200@30Hz, 2048x1080@30Hz or 1280x720@60Hz. Frame Sequential Dual Channel Progressive only Progressive only SDI (3G - L evel B) 3 Fpix ≤ 150MHz.
8. Inpu t Image 8-61 3D status 2. Press ENTER to t oggle between [On] and [Off] . [On] : 3D activated [Off] : 3D deactivated 8.9.3 Aut o detection About auto detection • Autom atically det ects the .
8. Input Image 8-62 Main window Image 8-63 Input, 3 D Image 8-64 3D, auto detecti on 8.9.4 Input type selection About input types • Frame sequential - Single channel : O ne input c ontains 3D information, alternating t he left and the r ight information.
8. Inpu t Image 8-65 Main window Image 8-66 Input, 3 D 2. Press ENT ER to open the 3D menu 3. Use the ▲ or ▼ key to select the des i red input type.
8. Input Image 8-70 3D second sourc e 2. Press ENTER to select. The Sour ce se l ect ion window opens. 3. Use the ▲ or ▼ key to select the desired i nput and press EN TER .
8. Inpu t Image 8-74 2. Press ENT ER . 3. Use the ▲ or ▼ key to selec t Field Dominance . Image 8-75 Field dom inance 4. Press ENTER to t oggle between [L/R] and [R/L] [L/R] : The 3D SYN C IN signal is used to indicate the l eft and right fi eld sequence.
8. Input Left 3D Sync Left Right Right Inverted 3D Sync Left Right Normal t Left Image 8-76 3D sync o ut How to toggle 3D S YNC OUT 1. Press Menu to activate the menus and select Alignment → 3D Glasses → L/R Synchronisation .
8. Inpu t Image 8-79 3D, L/R Synchroni sation 2. Press ENT ER . 3. Use the ▲ or ▼ key to select Invert 3D Sync Out . Image 8-80 Invert 3D Sy nc Out 4.
8. Input 104 R5905032 HDX SERIES 02/03/2015.
9. Image 9. IMAGE Overview • Image menu overview • Start up the Image adjustments • Image settings • Aspect R atio •T i m i n g s • Im age File Servic es • Save c ustom settings • Splash im age 9.
9. Image T otal vertical lines Active lines V ertical start Advanced settings Clamp delay Clamp width Press Auto Image for new measurement Image fi le service Manual load File load fi lter Delete Delete all Rename Copy Options Save c ustom settings Splash ima ge On or O f f T imeout(sec) 9.
9. Image How to adjust 1. Press Menu to activate t he menus and select Image → Image Settings → Contrast . Image 9-3 Main menu, Image Image 9-4 Image adjust ments Image 9-5 Image setti ngs, contras t 2.
9. Image Image 9-7 Main menu, Image Image 9-8 Image adjust ments Image 9-9 Image setti ngs, bright ness 2. Press ENTER to select. 3. T o change the value directly in the Image Settings window , use the ◄ or ► key or a numeric key 0-9, to adjust as a % of the full range.
9. Image Image 9-1 1 Main menu, Image Image 9-12 Image adjust ments Image 9-13 Image setti ngs, saturat ion 2. Press ENTER to select. Image 9-14 Saturat ion adjustme nt 3. T o change the value directly in the Image Settings window , use the ◄ or ► key or a numeric key 0-9, to adjust as a % of the full range.
9. Image Image 9-15 Jitte ring on image Phase adjustment can be done with the Phase key on the RCU or via the menu structure. How to adjust 1. Press Menu to activate the menus and select Image → Image Settings → Phase . Image 9-16 Main menu, Image Image 9-17 Image adjust ments Image 9-18 Image setti ngs, phase 2.
9. Image T o adjust via the bar scale menu, press EN TER to display the Phase menu and adjust with the ◄ or ► key . Pres s ENTER again to enter the value direc tly with the numeric keys.
9. Image Image 9-23 Depending o n the color space setting, a request window is displayed to as k if the color space setting should be switched t o Off Color temperature selection can only be done when the color space settings is set on Off . Image 9-24 Color tempera ture question Cl ic k Ye s to conti nue.
9. Image Image 9-27 Image setti ngs, col or temperatur e 2. Press ENTER to select. 3. Use the ▲ or ▼ key to select Cu stom Balance .P r e s s ENTER to accept. Image 9-28 Custom colo r tempera ture 4. Select Gain Red and press ENTE R .U s et h e ◄ or ► key to a djust t he red gain.
9. Image Bla c k le vel Δ G ΔΒ Δ R R G B Image 9-30 One can conclude here t hat a good color tracking can onl y be met by using t hree previou sly (input ) balanced color signals Analog Digital Conversion The analog color signals must pass through an Analog/Digit al conversion circuit prior to any digit al processing in the PMP .
9. Image A B Image 9-32 White balance : In the projector , we will set the contrast for eac h color until we get a 100% light o utput picture when projecting a 100% white image (image A) Black balance.
9. Image Image 9-36 Image setti ngs, input bal ance Image 9-37 2. Press ENTER to select. 3. Do you wan t to use an inter nally generated test pattern ? If yes, use the ▲ or ▼ key to sel ect Adjustm ent Pattern and press ENTER to t oggle between [ on] and [ off] If no, adjust o n the selected source.
9. Image Image 9-40 Image setti ngs, input bal ance Image 9-41 Input balan ce, white balance 3. Press ENTER to select. 4. Do you wan t to use an inter nally generated test pattern ? If yes, use the .
9. Image Image 9-42 Main menu, Image Image 9-43 Image adjust ments Image 9-44 Image setti ngs, defaul ts 2. Press ENTER to select. Ac o n fi rmation me nu is displayed Image 9-45 Default s con fi rma tion 3. Use the ▲ or ▼ key to select Y es and press Ent er to con fi rm.
9. Image Aspect ratio Description 16:9 Wide screen television for mat / anamorphic format 5:4 Workstation format 2.35 Fil m form at 1.88 Digital cinema 2K as pect ratio 1.85 35 mm US and UK wide screen standard fi lm f ormat 1.78 Wide screen television for mat / anamorphic format 1.
9. Image Image 9-49 Aspect rat io 4. Press ENTER to activate. How to set up the c ustom asp ect ratio 1. While Custom i s selected, use the ▲ or ▼ key t o selec t Se tup Cu stom and press ENTE R . Image 9-50 Custom aspect rati o Image 9-51 Custom aspect ratio adjust ment The custom a spect ratio setup menu ope ns.
9. Image • T otal l ines: T otal lines in t he source. How to set up 1. Press Menu to activate the menus and select Image → Timings . Image 9-52 Main menu, Image Image 9-53 Image, tim ings Image 9-54 Ti mings window 2. Press ENTER to select. 3. Use the ▲ or ▼ key to select a sett ing.
9. Image Sync pulse Clamp pulse Clamp dela y Clamp wid th Leading edge Tra iling ing ed ge Image 9-55 How to change the clamp delay - clamp width 1. Press Menu to activate the menus and select Image → Timings → Advanced settings . Image 9-56 Main menu, Image Image 9-57 Image, tim ings Image 9-58 Ti mings, advanc ed setti ngs 2.
9. Image 3. Use the ▲ or ▼ key to select Clamp Delay or Clamp Width and use the ◄ or ► key to change t he value. Or , pre ss ENTER to open the speci fi c adjust ment menu. Follow the adjustment method as descri bed in "Navigation and adjust- ments", page 72.
9. Image Depending on the File Load F ilter setting a full list or a list fi tting the selected source is displayed . When staying for at least 3 seconds on t he same fi le selection aft er scrolling t hrough the list of image fi les a pr e-load is started.
9. Image Image 9-66 File loa d fi lter 2. Press ENTER to t oggle between [All] and [Fit] . 9.6. 4 Delet e a fi le What can be done ? A custom image fi le can be deleted. Be aware that an active fi le can’t be deleted. How to delete 1. Press Menu to activate the menus and select Image → Image File Ser vices → Delete .
9. Image Image 9-70 Delete custom fi le 4. Press ENT ER to delete t he selected fi le. No recovery possible ! 9.6. 5 Delet e all cu sto m fi les What can be done ? All custom image fi les can be deleted by executing a single command. Be aw are that an acti ve fi le can’t be deleted.
9. Image Image 9-74 Delete all 3. If Ye s is selected, press ENT ER to delete all custom fi les. If No is selected, press ENTER to retur n to the Image File Services menu without deleting any cus tom fi le. No recovery possible ! 9.6.6 Rename cu stom fi les A rena me operat ion is onl y appli cabl e for custom i mage fi les.
9. Image The available custom fi les are displayed. If no custom fi les are available, a message that no custom fi les are available is displayed. Image 9-78 Renam e, list of fi les 3. Use the ▲ or ▼ key t o sel ect t he fi le to rename and press ENTER .
9. Image Image 9-82 Image fi le services, copy 2. Press ENTER to select. The available custom fi les are displayed. Image 9-83 Copy fi les, list If no custom fi les are available, a message that no custom fi les are available is displayed. Image 9-84 No custom fi les 3.
9. Image 9.6.8 Image fi le service options, Loa d fi le How to set 1. Press Menu to activate the menus and select Image → Image File Services → Options → Load File . Image 9-86 Main menu, Image Image 9-87 Image, image fi le service s Image 9-88 Image fi le ser vices, Option s Image 9-89 File option s, Load fi le 2.
9. Image Image 9-92 Image fi le ser vices, Option s Image 9-93 File opt ions, Aut o Pictur e Ali gnment 2. Press ENT ER to toggle between [Off] , [Always] or [Load File] . - Off : auto picture alignment deactivated. - Always : auto picture alignment i s always activated.
9. Image 9.8 Splash image About a splash image When splash image is on, a dedicated image is displayed after start up and befor e the normal image is displayed and that for a certain time. A splash image can be uploaded via Projector T oolset. F or more inf ormation about upl oading a splash image, consult Projector T oolset’s user guide.
9. Image Image 9-102 Splash screen , time-out 3. Press ENT ER to open the edit mode. Enter the time with 2 digits, e.g. 05 or 15. Note: Maximum timeout = 15 seconds.
9. Image 134 R5905032 HDX SERIES 02/03/2015.
10. Layou t 10. LA YOUT Overview • Layout m enu overview • Introduction • Ma in window • PiP w indow • Layou t File Service s • Lens behavior 10.
10. Layou t 10.3 Main window Overview • Ma in window source selection • Ma in window size • Ma in window position When starting the M ain window settings, the system will ask to create a custom layout 10.3.1 Main window source selection How to select 1.
10. Layou t Image 10-5 Size adjust ment main window A width adju stment B height adjustme nt The size can be changed with res pect to the or iginal aspect r atio by checking the check box in front of Lock . How to change the size 1. Press Menu to activate the menus and select Layout → Main window → Size .
10. Layou t The Size window opens. Image 10-9 Size window 3. T o keep the current aspect ratio, press ENTER to check Lock . Once Lock is checked, the width and the height will follow each other when changing one of the dimen sions. 4. Use the ▲ or ▼ key to chan ge the height and the ◄ or ► key t o change the width.
10. Layou t Image 10-12 Main me nu, la you t Image 10-13 Layout, main win dow Image 10-14 Main window , P ositi on 2. Press ENTER to select. The Pos it i on window opens. Image 10-15 Positi on window 3. Use the ▲ or ▼ key to change the To p position and the ◄ or ► key to change the Left posit ion.
10. Layou t When starting the PiP window settings, t he system will ask to create a custom layout 10.4.1 Introduction to PIP PiP PiP stands for "Pictur e in Picture" and all o ws to displa y multiple windows containing each of them a n image.
10. Layou t Image 10-20 PiP window , activa tion 2. Press ENTER to t oggle between [On] or [Off] . 10.4.3 PiP window , s ource selection How to select 1. Press Menu to activ ate the menus and select Layout → PiP window → Source . Image 10-21 Main me nu, la you t Image 10-22 Layout, Pi P Window Image 10-23 PiP window , source select ion 2.
10. Layou t 10.4.4 PiP window, Size What can be done? The width and height of the picture in picture window can be changed till the desired dimensions are obtained.
10. Layou t Image 10-29 PiP w indow, size 2. Press ENTER to select. The Size window opens. Image 10-30 PiP window , resize 3. T o keep the current aspect ratio, press ENTER to check Lock . Once Lock is checked, the width and the height will follow each other when changing one of the dimen sions.
10. Layou t Image 10-32 Main me nu, la you t Image 10-33 Layout, Pi P window Image 10-34 PiP window , position 2. Press ENTER to select. The Pos it i on window opens. Image 10-35 Positi on window 3. Use the ▲ or ▼ key to change the To p position and the ◄ or ► key to change the Left posit ion.
10. Layou t 10.5 Layout File Services Overview • Load layout fi le • Renam e layout fi le • Delete layout fi le • Delete a ll layout fi les • Copy or Save as layout fi le 10.5.1 Load layout fi le When loading a layout t hat requires t wo sources, t he PiP window On/Off s ettin g will be sw itched to On.
10. Layou t Image 10-40 Load layou t fi le list 3. Use the ▲ or ▼ key to selec t the desired fi le and press ENTER to activ ate. The radio button in front of the selected fi le is checked. 10.5.2 Rename layout fi le Only custom created layouts can b e renamed.
10. Layou t The Rename layout window opens with all available custom l ayouts. Image 10-44 3. Use the ▲ or ▼ key to select the desir ed custom fi le and p ress ENTE R to start t he renaming. The Rename window opens. Image 10-45 Rename layout 4. Use the ▲ or ▼ key to change the selected character .
10. Layou t The Delete layout window opens with all available custom l ayouts. If no custom layout fi les are available, a message that no c ustom layout fi les are available is displayed. Image 10-49 3. Use the ▲ or ▼ key to select the desired custom fi le and press ENTER to delete.
10. Layou t The Delete all con fi rm window opens. If no custom fi les are available, a message that no custom fi les are available is displayed. Image 10-54 Layout fi les , delete all con fi rmat ion 3. Use the ▲ or ▼ key to select Ye s .P r e s s ENTER t o delete al l layout fi les.
10. Layou t Use t he ◄ or ► key to select another character . Note: Digits can be entered with the digit keys on the remote control or the local keypad. When a digit is entered in that way , the next character will be selected automaticall y . Arrow key left ( ◄ ) has the backspace functionality .
10. Layou t Before diff erent zoom/focus/shift set ting can be used, the lens should be calibrated. When a lens change has taken place, always calibrate the lens befor e using this s etting. 5. If you have to calibrate the lens, select Ye s and press ENTER to star t the calibr ation.
10. Layou t 152 R5905032 HDX SERIES 02/03/2015.
11. Lamp 11 . L A M P Overview • Lam p menu overview • Lam p power mode • Lam p power • Auto dimm ing when on Pause • Auto dimm ing when No Signal • Auto dimming when O ver-temperature • CLO mode (Con stant li ght output mode) • CLO targets • LPS power • Lam p identi fi cation • Z-axis adjustment 1 1.
11. Lam p Image 1 1-1 Main me nu, la mp Image 1 1-2 Lamp, power Image 1 1-3 2. Press ENTER to toggle between [Normal] , [Economic] and [Long Life] . 1 1.3 Lamp power What can be done? Within a cert ain power mode, the light output of t he lamp can be reduced by r educing the lamp power How to reduce the power 1.
11. Lamp Image 1 1-6 Lamp power adjustment 2. Use the ◄ or ► key to chang e the power value. The value can be changed between 75 an d 100% 1 1.4 Auto dimming when on Pau se About auto dimming when o n pause When the projector is switched to pause, the shutter is closed but t he lamp is still ru nning on f ull power .
11. Lam p Image 1 1-9 Auto dimmi ng when Pause 2. Press ENTER to t oggle between [On] or [Off] . [On] : when switched to pause, lamp power will be reduced.
11. Lamp Image 1 1-12 Auto dimmin g no signal 2. Press ENTER to t oggle between [On] or [Off] . [On] : when no signal, auto dimming is started. [Off] : w hen no si gnal, no auto dimming is started.
11. Lam p Image 1 1-15 Auto dimmi ng over-t emperatur e 2. Press ENTER to t oggle between [On] or [Off] . [On] : when temperature is to high, auto dimming is start ed.
11. Lamp 100 20 40 60 80 200 400 600 800 1000 Relative Light Output (%) Runtime (hrs) Constant Light Output working area Image 1 1-17 CLO mode setting On overrules the lam p power mode setting. Projector will always play in CLO m ode using the CL O targe t.
11. Lam p 11 . 8 C L O t a r g e t s What must be done? The light output target can be set. This value w i ll force the pr ojector to produce the t arget lumens when the CLO mode is set to On. How to set the target 1. Press Menu to acti vate the menus and s elect Lamp → Powe r → CLO mode .
11. Lamp Image 1 1-24 LPS power 1 1.10 Lamp identi fi cati on About The lamp identi fi cation menu gives an overview of the most important parameters of the used lamp.
11. Lam p Image 1 1-27 Lam p ident i fi cation 1 1 . 1 1Z - a x i sa d j u s t m e n t What can be done? The Z-Axi s menu item gives the current light output of the projector (i n percentage). This light output indication can be used to readjust the lamp position in the lamp casing (also called Z-ax is adjustment of the lamp).
12. Al ignm ent 12. ALIG NMENT Overview • Alignm ent menu overview • Orientation • Lens a djust ment, zoom - focus • Lens adjustment, shift • Lens a djust ment, m id posit ion • Calbrate l.
12. Ali gnment Color Space Status Projector EBU SMPTE Custom Custom2 ScenergiX Status White level Black level ScenergiX pattern Adjust lines Reset 3D Glasses Dark T ime Adjustment Actual Dark T ime L/R Output Reference Delay 3D Sync Loop Th rough High End Systems M irror Proj ector Controlled Pan / T ilt Store setting per layout 12.
12. Al ignm ent Image 12-1 Main menu, alignmen t Image 12-2 Alignme nt, ori entatio n 2. Use the ▲ or ▼ key to select the desired orientation and press ENTER to a ctiv ate. Image 12-3 Orienta tion list 12.3 Lens adjustment, zoom - focus Zoom/Focus adjustment 1.
12. Ali gnment Image 12-6 Lens, Zoom/ Focus 3. Use the ▲ or ▼ key to zoom the lens. Use t he ◄ or ► key to focus the lens. Pres s ENTER t o switch to Lens shift adjustment. Image 12-7 Zoom/Focus adj ustment 12.4 Lens adjustment, shift How to shift le ns 1.
12. Al ignm ent Image 12-10 Lens, shi ft 3. Use the ▲ or ▼ ke y to shift the lens in vertical direction. Use t he ◄ or ► key t o shift the lens in horizontal direction. Pres s ENTER to switch to Zoom/Focus adjustment. Image 12-1 1 Shift ad justment 12.
12. Ali gnment Image 12-14 Lens, mid posi tion Lens will be shifted horizontal ly and vertically to it s mid position. 12.6 C albrate lens at startup About calibrating lens Each time the projector is start ed, a homing procedure (calibration) can be executed so that the project or exactly knows the lens position.
12. Al ignm ent 12.7 Calibrate lens Lens c alibrat ion is a tim e cons umin g opera tion. How to calibrate 1. Press Menu to activate the menus and select Alignment → Lens . Image 12-18 Main menu, alignmen t Image 12-19 Alignme nt, lens 2. Use the ▲ or ▼ key to s elect Calibrate lens and pr ess ENTER to ac tiv ate.
12. Ali gnment 12.8 W arping Not al l models are e quip ped with a war ping uni t. For these model s, the warping un it is op tional . Overview • Abo ut warping • Warp activation - deactivation .
12. Al ignm ent 12.8.2 W arp activat ion - dea ctivation What can be done ? The Warp functi onality can be activated or deactivated. With 3D activated, warping can be enabled for sources up to 30 Hz per eye. Above this frequency , warping is disabled.
12. Ali gnment The Warp adjust menu opens. The content of this warp adjust menu depends on the selection. When no warp was done before, the menu starts as a sort of wizard by opening only the warp ar ea pane. It opens more and more panes depending on the selection.
12. Al ignm ent 12.8.4 W arp adjustment princ iple Descriptio n W arping adjustment enables the relocation of pixel groups in an image in order to introduce spacial distortion. T o make the procedure comprehensible, there are some rules and featur es.
12. Ali gnment In 2 x 2 mode, we only have one level, including all four (2 x 2) anchor point s, being the image corners. This m ode is especially used to corr ect horizontal and vertical keystone.
12. Al ignm ent 12.8.5 Setting t he warping level How to select 1. With the Warping menu display ed, use the ▲ or ▼ key to select more or less pixels to adjust.
12. Ali gnment Image 12-38 Warp adap tati on steps The following selection is possible: - 100 pixels -1 0 p i x e l s -1 p i x e l -C u s t o m 3. Press ENT ER to accept t he selection. When Custom is selected, the step value can be changed. How to change the custom step value 1.
12. Al ignm ent 4. T o adjust a value once selec ted, use the ◄ or ► key to change Or , pre ss ENTER to open a separate adjustment window . Use the arrow keys to make the adjustment.
12. Ali gnment Or , pre ss ENTER when an item is selected and use the 4 arrow keys to adjust. Image 12-43 Warp ing, ke ystone 5. Move the corner points t o the desired position. Image 12-44 Keyston e adjust ment 12.8.9 Linearity a djustment, work fl ow Adjusting vertical and horizontal linear ity 1.
12. Al ignm ent 12.8.10 Selecting and changing the position of a speci fi cp o i n t About point selection Depending on the warp level, number of s electable points, a speci fi c point c an be selected and moved in any directi on. The coordi- nate system works with 33 x 33 pixels (0 to 32).
12. Ali gnment Depending on the selected area only the points in that area will be adjusted and the scale direction changes according the sele cti on. 3. Select Scale . 4. Select within Warp Adaptations , an available adjustment to scale the im age. Or , pre ss ENTER when an item is selected and use the 4 arrow keys to adjust.
12. Al ignm ent Image 12-51 Rotation Selecting ro tation poin t 1. Select full image as warp area (1). 1 2 3 Image 12-52 Rotati on point, se lecti on 2. Use the arrow keys to select Rotation point (2). 3. Select Warp Adaptati ons and use the arrow keys to move rotati on point to the desired positi on (3).
12. Ali gnment 1 2 3 Image 12-54 Rotate image 3. Select Warp adaptation, angle. 4. Use the ◄ or ► key to change the rotation Angle . Or , pre ss EN TER t o open the W ar ping Adaptations window . Use the ◄ or ► key to change the Angle. Image 12-55 Warp ing ad aptation , angle 12.
12. Al ignm ent 1 21 11 6 16 5 3 2 4 25 15 23 13 24 22 10 20 8 18 12 14 7 9 19 17 1 3 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 18 1 18 18 18 1 1 1 18 1 1 18 1 1 1 1 18 1 18 1 1 2 2 12 12 2 1 1 1 1 1 1 1 1 1 7 1 7 1 1 17 17 1 1 1 1 17 17 17 1 1 7 7 1 1 17 7 7 1 1 1 1 1 1 7 1 17 1 1 7 Image 12-57 Opaci ty How to adjust 1.
12. Ali gnment 12.8.16 Warp fi le service, load fi le What can be done? A prede fi ned warp con fi guration can be loaded in the warp board as ac tive warp con fi guration fi le. T o exclude the warp functionality , load the fi le NoDistort ion.
12. Al ignm ent 12.8.17 Warp fi le se rvi ce, sa ve to fi le What can be done? The current warp settings are saved in the current active fi le How to save 1. Press Menu to activate the menus and select Alignment → Warp in g → . Warp File Se rvice → .
12. Ali gnment Image 12-70 Main menu, alignmen t Image 12-71 Alignm ent, Warping Image 12-72 Warpi ng, fi le se rvi ce Image 12-73 Save as 2. Press ENTER to open t he Enter the name w indow . The current active fi le name is displayed. 3. Use the ▲ or ▼ key to change the selected character .
12. Al ignm ent Image 12-74 Main menu, alignmen t Image 12-75 Alignm ent, Warping Image 12-76 Warpi ng, fi le se rvi ce Image 12-77 Rename warp fi le Image 12-78 Warp fi les Image 12-79 Rename fi le 2. Press ENTER to display the list of warp fi les .
12. Ali gnment Image 12-80 Main menu, alignmen t Image 12-81 Alignm ent, Warping Image 12-82 Warpi ng, fi le se rvi ce Image 12-83 Delete warp fi le 2. Press ENT ER to display the Warp fi l e list. Image 12-84 Warp fi les Image 12-85 Con fi rm dele te 3.
12. Al ignm ent Image 12-86 Main menu, alignmen t Image 12-87 Alignm ent, Warping Image 12-88 Warpi ng, fi le se rvi ce Image 12-89 Delete all Image 12-90 Con fi rm delete 2. Press ENT ER . 3. Use the ▲ or ▼ key to Y es or No and pr ess ENTE R .
12. Ali gnment Image 12-91 Main menu, alignmen t Image 12-92 Alignm ent, Warping Image 12-93 Warp boar d reset 2. Press ENT ER to start the board reset. 12.8.23 Warp board an d values rese t What can be done? With some extreme warp values the hardware of the warping can get stuck.
12. Al ignm ent Image 12-94 Main menu, alignmen t Image 12-95 Alignm ent, Warping Image 12-96 Warp boa rd and v alues reset 2. Press ENT ER to reset the board and the cur rent warp values.
12. Ali gnment Image 12-97 Main menu, alignmen t Image 12-98 Alignm ent, Warping Image 12-99 Alternati ve side keystone 2. Use the ▲ or ▼ key to adjust t he keystone.
12. Al ignm ent Image 12-100 Blanking A T op blankin g B Bottom blanking C Left blanki ng D Right blankin g The reset function bri ngs all blanking settings back to zer o. How to adjust 1. Press Menu to activate the menus and select Ali gnment → Blanking .
12. Ali gnment The blanking adjustment menu opens. Image 12-103 Blanking adj ustment 3. Use the ▲ or ▼ key to select the desired blanking adjus tment and adjust with the ◄ or ► key .
12. Al ignm ent Use t he ◄ or ► key t o change the intensity until the desir ed value is reached (adjustable between 0 and 2 55) Image 12-107 Intensity 12.
12. Ali gnment Image 12-1 10 Main menu, alignmen t Image 12-1 1 1 Alignment, intern al patterns 2. Press ENT ER to select the pattern list. Image 12-1 12 OSD test pat terns 3. Use the ▲ or ▼ key to select a pattern and press ENT ER to display that pattern.
12. Al ignm ent 12.13 Color space Color space A color space or color standard is a mathematical representation for a color . For example the R GB color space is based on a Cartesi an coordinate syst em.
12. Ali gnment Image 12-1 16 4. Whe n [On] is selected and the color temperature is correct, use the ▲ or ▼ key to select the desired color space and press ENTER to selec t. Projector Maximum color space EBU European Broadcasting Union. This organization de fi nes a European standard.
12. Al ignm ent 2. Use the ▲ or ▼ key to select a color coordinate. Use t he ◄ or ► key to change the value of t he selected coordinate. Adjust all other c oordinates in the same way . Select Reset to return to previous saved values. 12.14 Scenergix 12.
12. Ali gnment 12.14. 2 Preparatio ns Scenerg iX Prepara tions T o ensure proper ScenergiX adjustment, be sure that the following adjustments are done perfectl y on all projectors: • Convergence • Geometry • Color M atching (Color T emperature, Color S tandard, Input Balance, G amma) 12.
12. Al ignm ent Image 12-124 Main menu, alignmen t Image 12-125 Alignme nt, Scener gix Image 12-126 Scenergix, pat tern act ivation 2. Press ENTER to t oggle between [On] or [Off] . [On] : Internal scenergix pattern is displayed. [Off] : no scenergix pattern i s displayed.
12. Ali gnment Adjustment lines can be activated when S cenergix pattern is [O n]. How to display 1. Press Me nu to acti vate the menus and select Alignment → Scenergix → Adjust lines . Image 12-128 Main menu, alignmen t Image 12-129 Alignme nt, Scener gix Image 12-130 2.
12. Al ignm ent Pr ojector 1 Pr ojector 2 Hor . Star t 1 Ve r t . Star t 1&2 Hor . Star t 2 A B Size 1 Size 2 Size V Image 12-131 Data doubli ng AS o u r c e B Projected image Activate data doubling on both projectors and setup the vertic al and horizontal start for proj ector 1 and projector 2.
12. Ali gnment Image 12-132 Main menu, alignmen t Image 12-133 Alignme nt, Scener gix Image 12-134 Scenergix, data doubli ng Image 12-135 Data doubli ng, status 2. Select Status and press EN TER to toggle between [O n] and [Off] . [On] : data doubling is act ivated.
12. Al ignm ent Image 12-136 Main menu, alignmen t Image 12-137 Alignme nt, Scener gix Image 12-138 Scenergix, whi te level 2. Press ENTER to select the White level adjustments. The White level position menu opens. When Adjus tment lines is [On] , the diff erent areas are displayed on the screen.
12. Ali gnment Image 12-140 Width se lections 4. Set fi rst the w idth for the fi rst projector and repeat for the second one. Image 12-141 Wi dth set up for pro jecto r 1 206 R5905032 HDX SERIES 02.
12. Al ignm ent Image 12-142 Wi dth set up fo r proj ector 2 T o eliminate all blending settin gs, select Reset and press EN TER. 12.14.8 Blac k level ad justment Why black le vel adjustment For dark images, the overlap zone will be brighter then the r est of the images.
12. Ali gnment Image 12-144 Main menu, alignmen t Image 12-145 Alignme nt, Scener gix Image 12-146 Scenergix, Black l evel 2. Press ENTER to select the Black Level adjustm ents. Image 12-147 Black level , area 3. Use the ▲ or ▼ key to select one of the four size adjustments.
12. Al ignm ent Image 12-148 DLP leakage ar ea 1 Overlap area 2 DLP Leakage area Use the Reset item to reset all area values. How to adjust 1. Press Me nu to acti vate the menus and selec t Alignment → Scenergix → Black l ev el .
12. Ali gnment Image 12-151 Scenergix, Black l evel 2. Press EN TER to select and use the ▲ or ▼ key to select a color to adjust or select All colors to adjust all c olors at the same time. Image 12-152 Black lev el, adjust 3. Adjust the black level of area A until the black level of area A, B and C are equal.
12. Al ignm ent How to reset 1. Press Menu to activ ate the menus and select Alignment → Scenergix → Re set . Image 12-154 Main menu, alignmen t Image 12-155 Alignme nt, Scener gix Image 12-156 Scenergix, r eset 2. Press ENTER to reset t he Scenergix value.
12. Ali gnment Left Shutter Open O p e n i n g O p e n i n g C l o s i n g C l o s i n g Close d Right Sh utter Open Close d DL P Mi rro rs Active Blanking Ti me Opening + Closing = Blanking T ime t S.
12. Al ignm ent Left Shutter Open O p e n i n g O p e n i n g C l o s i n g C l o s i n g Close d Right Sh utter Open Close d DL P Mi rro rs Active Blanking Ti me Opening Too Late and/ or Closing Too .
12. Ali gnment Image 12-162 Dar k ti me adj ust men t 4. Use the ◄ or ► key to c hange the dark time until the correct value is reached. The actual used dark time is indicated nex t to Actual Dark Time .
12. Al ignm ent Image 12-164 Main window Image 12-165 Alignme nt, 3D glasses 2. Press ENT ER . 3. Use the ▲ or ▼ key to select L/R O utput Reference Delay Image 12-166 Output r eferenc e della y 4. Use the ◄ or ► key to chang e the L/R Output Reference Delay value until the correct value is reached.
12. Ali gnment 2. Press ENT ER . 3. Use the ▲ or ▼ key to select 3D S ync Loop Through . Image 12-169 3D sync loop th rough 4. Press ENTER to t oggle between [On] and [Off] .
12. Al ignm ent Image 12-172 2. Use the ▲ or ▼ key to s elect Projector Controlled and press ENTER t o toggle bet ween [On] and [Off] . [On] : High End Systems M irror is controlled via the projector . [Off] : High End Systems Mirror is not c ontrolled vi a the projector .
12. Ali gnment [No] : settings are stored globally . [Y es] : settings are stored per layou t. 218 R5905032 HDX SERIES 02/03/2015.
13. Proj ector Control 13. PROJECT OR CONTROL Overview • Projector Control m enu overview • Individual Projector Address • Projector Common A ddress • Serial Comm unication •N e t w o r k .
13. Projec tor Contr ol Shutdown time Buttons Shortcut keys Standby button Menu position Menu position Bar scale pos ition Local LCD Back light Time out Change Language Scheduler Add ta sk Edit t ask Del ete ta s k Scheduler on/off GSM con fi guration PIN c ode SMS subscription 13.
13. Proj ector Control Image 13-4 Proje ctor addre ss, input 3. Use the ▲ or ▼ key to change the selected character . Use t he ◄ or ► key to select another character . Note: Digits can be entered with the digit keys on the remote control or the local keypad.
13. Projec tor Contr ol 13.4 Serial Communicati on Overview • Baud rate setup • Interface Standard 13.4.1 Baud rate setup What can be done ? The baud rate for to establish a serial communication with a computer can be s et. How to set 1. Press Menu to activate the menus and select Projector Control → Serial Comm unicat ion → Baudrate .
13. Proj ector Control Image 13-12 Main menu, projector contro l Image 13-13 Projecto r control , serial c ommunicat ion 2. Use the ▲ or ▼ key to select Interface Standard . Pres s ENTER to toggle bet ween [RS232] or [RS422] . Image 13-14 Interfa ce standa rd 13.
13. Projec tor Contr ol IP Internet Protocol. The network layer of TCP/IP . Required for communication with the internet. Subnet mask A number that is used to identi fy a subnetwork so that IP addresses can be shared on a l ocal area network. Default Gateway A router that serves as an entry point into and exit point out of a network.
13. Proj ector Control Image 13-17 Wir ed DHCP 2. Use the ▲ or ▼ key to select D HCP under Wired and press EN TER to toggle between [O n] or [Off] . [On] : DHCP is activated. An automatic IP address is assigned. [Off] : D HCP is de act ivated. A fi xed address must be used.
13. Projec tor Contr ol Image 13-20 2. Use the ▲ or ▼ key to s elect IP Address under Wired and press ENTER t o activate the input box. Image 13-21 3. Use the ▲ or ▼ key to change the selected character . Use t he ◄ or ► key to select another character .
13. Proj ector Control Image 13-22 Main menu, projector contro l Image 13-23 Projecto r contr ol, network Image 13-24 Subnet mask 2. Use the ▲ or ▼ key to select S ubnet Mask under Wired and press ENT ER to acti vate the input box. Image 13-25 3. Use the ▲ or ▼ key to change the selected character .
13. Projec tor Contr ol 13.5.5 Wired def ault gateway set up How to set up 1. Press Menu to acti vate the menus and s elect Projector Control → Network . Image 13-26 Main menu, projector contro l Image 13-27 Projecto r contr ol, network Image 13-28 Network, defaul t gateway 2.
13. Proj ector Control Image 13-29 Default Gat eway , input 3. Use the ▲ or ▼ key to change the selected character . Use t he ◄ or ► key to select another character . Note: Digits can be entered with the digit keys on the remote control or the local keypad.
13. Projec tor Contr ol Image 13-32 Network, wireless 2. Press ENTER to select. Image 13-33 Wireless, status 3. Press EN TER to toggle the status between [Of f] and [On] . 13.5.7 Wireless acce ss points s election a nd setup These menu items are only accessible when wireless network status i s set to [on].
13. Proj ector Control Image 13-34 Scan access points Image 13-35 Scan access poi nts, result s 2. Use the ▲ or ▼ ke y to select t he desired access point and press ENTER to a ctiv ate . The security type of the network is indic ated with the radio button in front of Open or WP A/WP A2 .
13. Projec tor Contr ol Image 13-38 Open network con nection 2. Press ENT ER to acti vate the input fi eld. 3. Enter the passphrase. T he input is case sensitive. Pres s ENTER to fi ni s h the input of the passphrase. 4. Use the ▲ or ▼ key to select A pply and press ENTER to open the network connection.
13. Proj ector Control Image 13-41 Network, wireless Image 13-42 Wireless, DHCP 2. Press ENT ER to open the Wire le ss menu. 3. Use the ▲ or ▼ key to selec t DHCP and press ENTER to t oggle between [On] or [Off] . [On] : Wireless DHCP is activated.
13. Projec tor Contr ol Image 13-45 Network, wireless Image 13-46 Network, wireless 2. Use the ▲ or ▼ ke y to select IP Address and press ENTER to activate t he input box. Image 13-47 Wirele ss IP addres s input 3. Press ENT ER to open the Wire le ss menu.
13. Proj ector Control Image 13-48 Main menu, projector contro l Image 13-49 Projecto r contr ol, network Image 13-50 Network, wireless Image 13-51 Network, wireless Subnet Mask 2. Press ENT ER to open the Wire le ss menu. 3. Use the ▲ or ▼ key to selec t Subnet Mask and press ENT ER to acti vate the input box .
13. Projec tor Contr ol Image 13-52 Wirele ss Subnet Mask, input 4. Use the ▲ or ▼ key to change the selected character . Use t he ◄ or ► key to select another character . Note: Digits can be entered with the digit keys on the remote control or the local keypad.
13. Proj ector Control Image 13-55 Network, wireless Image 13-56 Wireless de fault gat eway 2. Press ENT ER to open the Wire le ss menu. 3. Use the ▲ or ▼ key to selec t Subnet Mask and press ENT ER to acti vate the input box . Image 13-57 Wirele ss defaul t gateway , input 4.
13. Projec tor Contr ol Image 13-58 Main menu, projector contro l Image 13-59 Projecto r contr ol, IR contro l Image 13-60 IR control 2. Use the ▲ or ▼ key to select the desired IR contr ol and press ENTER to check checkbox. Checked : IR rec eiver is enabled and can receive and p rocess commands sent by the rem ote control.
13. Proj ector Control How to set the DMX address 1. Press Menu to activat e the menus and select Projector Control → DMX → A ddress . Image 13-61 Main menu, projector contro l Image 13-62 Projecto r control , DMX Image 13-63 DMX, address 2. Press ENTER to select.
13. Projec tor Contr ol 13.7.2 DMX un iverse What can be done ? Depending on the DMX mode, one DMX universe can contain a di ff erent number of projec tors. E.g. D MX mode = basic, the DMX universe can contain up t o 256 projectors Universes are only meaningful for Art-Net applications as only there m ultiple universes can be addressed.
13. Proj ector Control Image 13-68 DMX universe 3. Use the ▲ or ▼ key to change the selected character . Use t he ◄ or ► key to select another character . Note: Digits can be entered with the digit keys on the remote control or the local keypad.
13. Projec tor Contr ol Image 13-71 DMX mode 2. Press ENT ER to toggle between [Ba sic] , [Extended] or [Full] . 13.7.4 Art-Net DM X What can be done ? DMX can be sent via Ethernet to the projector . This functi on can be enabled or disabled. Art-Net DMX [On] : DM X via Ethernet is enabled.
13. Proj ector Control Image 13-74 DMX Art-Net activatio n 2. Press ENTER to t oggle between [On] and [Off] . 13.7.5 Front XLR output voltage control What can be done ? The output voltage on the front XLR connector can be enabled or disabled. The output voltage level can be set to 0V , 9V , 12V or 24V .
13. Projec tor Contr ol Image 13-77 Front XLR Out put volt age enable 2. Press ENTER to t oggle between [On] and [Off] . [On] : Front XLR Output voltage e nabled. [Off] : Front XLR O utput voltage disabled. Outpu t volta ge leve l setup 1. Press Menu to activate the menus and select Projector Control → DMX → Output voltage level .
13. Proj ector Control 13.7.6 Monitor What can be done ? If a DMX device is connected, t he settings per c hannel can be displayed in an on screen menu. How to start up the monitoring 1. Press Menu to activate t he menus and select Projector Control → DMX → Monitor .
13. Projec tor Contr ol Image 13-84 DMX ov erview list 13.7.7 DMX Shutdown What can be done? Projector can be forced to go in shutdown after a certain retarding time when no DM X signals are available. How to act ivate/deac tivate 1. Press Me nu to acti vate the menus and select Projector Control → DMX → Shutdown .
13. Proj ector Control Image 13-87 DMX shutdown 2. Press ENTER to t oggle between [On] and [Off] . [On] : projector goes in shutdown after a c ertain retarding t ime.
13. Projec tor Contr ol Image 13-90 DMX shutdown time 2. Press ENT ER to toggle between [1] , [3 ] , [5] and [10] minu te s. 13.8 Buttons Overview • Standby button • Sho rt cut keys 13.
13. Proj ector Control Image 13-93 Buttons, sta ndby 2. Press ENT ER to toggle between [Lamp only] and [Lamp and P ower] . Lamp only : only lamp wil l be switched of f when Standby is pressed. O ther electronics remain powered. Lamp a nd Power : lamp will be s witched of f and projector will be powered down.
13. Projec tor Contr ol 13.9 Menu position What is possible? The on screen menu and the bar scale can be positioned on dif ferent places on t he screen.
13. Proj ector Control Image 13-101 Main menu, projector contro l Image 13-102 Projecto r control , Local LCD 2. Use the ▲ or ▼ key to select Back Light . Image 13-103 Local LCD, back light 3. Use the ◄ or ► key to change the ba ck lighting of the local LCD panel.
13. Projec tor Contr ol How to change the language 1. Press Me nu to acti vate the menus and select Projector Control → Change Language . Image 13-105 Main menu, projector contro l Image 13-106 Projecto r control , change la nguage Image 13-107 Language selec tion 2.
13. Proj ector Control Overview • Add a task t o the list •E d i t a t a s k • Delete task • Scheduler , on or off 13.12.1 Ad d a task to the list How to add 1. Press Menu to activate the menus and select Projector Control → Scheduler → Add task .
13. Projec tor Contr ol Image 13-1 1 1 Add task, setup Start d ate and tim e 1. Whe n selected, press ENTER to select the day . 2. Use the ▲ or ▼ key to change the current setting. Use t he ◄ or ► key to jump to t he next part of the date and t ime setti ng.
13. Proj ector Control Recurrence : the time between two starts of the same task. The value c an be changed between 1 and 99. 1 Start s every day 2 Starts every 2 days 3 Starts every 3 days .
13. Projec tor Contr ol The task is added to the list o f t asks. 13.12.2 E dit a task What can be done? An existing task in the list of tasks can be edited and s aved with the same name. How to edit 1. Press Menu to activate the menus and select Projector Control → Scheduler → Edit task .
13. Proj ector Control The edit task window opens. Image 13-120 Edit task The following items can be changed in the same way as creating a new task. For more info, see "Add a task to the list&quo.
13. Projec tor Contr ol Image 13-123 Scheduler , delete task 2. Press ENT ER to open the list of tasks. Image 13-124 Delete task, kist 3. Use the ▲ or ▼ key to select the tas k to delete and pres s ENTER . Ac o n fi rmation window o pens. Image 13-125 4.
13. Proj ector Control Image 13-128 Scheduler , on or off 2. Press ENTER to t oggle between [On] and [Off] On S cheduler will execute the tasks in the lis t. A schedule symbol is added at t he left bott om corner of the local LCD panel ( .) Of f No tasks are e xecuted 13.
13. Projec tor Contr ol Image 13-129 Main menu, projector contro l Image 13-130 Projecto r control , GSM con fi gurati on Image 13-131 GSM con fi gur ation Image 13-132 GSM pincode 2. Select Pin code and press ENTER . A PIN code input fi eld appears.
13. Proj ector Control Image 13-135 Main menu, projector contro l Image 13-136 Projecto r control , GSM con fi gurati on Image 13-137 GSM con fi guration , Pin cod e 2. Select Pin code with the current fi lled out code and press ENTER to clear the current code.
13. Projec tor Contr ol Image 13-139 Main menu, projector contro l Image 13-140 Projecto r control , GSM con fi gurati on Image 13-141 SMS subscri ption Image 13-142 Subscriber 2. Select Subsc riber 1 and press ENT ER . Image 13-143 3. Enter the GSM n umber of Subscriber 1.
13. Proj ector Control Image 13-144 Main menu, projector contro l Image 13-145 Projecto r control , GSM con fi gurati on Image 13-146 SMS subscri ption Image 13-147 Subscriber 1 2. Press ENT ER to open the Edit mode. Clear t he current number and press ENTER again.
13. Projec tor Contr ol T ol o c kt oas p e c i fi c value a 4 digit code is necessary; These codes can be c reated by the projector owner us ing Projector T oo lset. 13.15.2 Light output con fi guration via OSD me nu What can be done ? The activati on code can be entered by the projector user .
13. Proj ector Control 13.15.3 C on fi gure projector ’ s light o utput via SMS Proj ecto r must be equi pped with t he opti onal GSM modul e. What can be done ? An SMS message with certain structure must be sent to the SIM car d of the project or .
13. Projec tor Contr ol 13.16.2 Req uest for info rmation Request for information Via an SMS message sent from any cell phone to the GSM num ber associated with t he projector , projector information can be re- quested. The receiving projector ana l yses the message.
14. Service 14. SER VICE Overview • Service menu overview • Identi fi cat ion • Diagnosis • Internal Service Patterns • Convergence • Factory defaults • US B memory • Rese t Formatter •R e fi ll mode • Save Cus tom Settings • Special HD Cam era mode • Auto Dimm ing when over-temperat ure • Time and Date 14.
14. Ser vice 14.2 Identi fi cati on What ca n be see n? The identi fi cation screen shows the general information about the projector . The following items will be displayed : • Projector type •.
14. Service Image 14-3 Identi fi cati on 2. Use the ▲ or ▼ key to sc roll t hrough the menu. 14.3 Diagnosis What ca n be see n? The diagnosis menu gives the poss ibilit y to get an overview of the working of the projector . Overview • V ersi ons • Meas ureme nt s • Logging •B o a r d I d •N o t i fi cation • Tilt sensor 14.
14. Ser vice Image 14-4 Main me nu, se rv ice Image 14-5 Service, di agnosis Image 14-6 Diagnosis, ve rsions 2. Press ENTER to display an overview of the versions.
14. Service • V oltages • T emperatures • Fan speeds All tables are built up in an identical way . The current measured value is surrounded with the low and high er ror and warning limits. Once one of these values are crossed the threshold an error or warning message is logged or displayed on the local LCD screen.
14. Ser vice Image 14-13 Overview temp eratures Image 14-14 Overview fan speed s Image 14-15 Overview miscel laneous i tems 14.3.3 Logging What can be done? Projector hosts two log fi les: one managed bythe Main c ontroller and one speci fi c for the Lamp pow er supply .
14. Service Image 14-16 Main me nu, se rv ice Image 14-17 Service, di agnosis Image 14-18 Diagnosis, l ogging Image 14-19 Logging, mai n control ler 2. Use the ▲ or ▼ key to select Main C ontroller to get a logging of the main controller or to select Lam p Power Supply to get a logging of the lamp power supply .
14. Ser vice Image 14-21 Lamp power suppl y logging 14.3.4 Board Id About Board Id The board id window gives an over view of the modules with their art icle number , serial number , etc. How to g et an over vie w 1. Press Menu to activ ate the menus and select Serv ic e → Diagnosis → Board Id .
14. Service Image 14-25 Overvi ew board IDs 14.3.5 Noti fi cati on About noti fi cations Noti fi cat ions are warnings and errors di splayed on the local LCD or on the OSD since power on of the projec tor . Once powered off, the noti fi cation logging is c leared.
14. Ser vice Image 14-29 Noti fi ca tion over view li st 14.3.6 Tilt sensor What is possible? The built-in til t sensor can be read out to see if t he projector is us ed in an allowed position. The status fi eld indicates whether the rotation of t he projector is normal or abnormal.
14. Service Image 14-33 T ilt sens or output The rotation of the pr ojector is vis ually displayed. Coordinates of the tilt sensor and the offset f rom the normal position are gi ven in the tilt sensor pane. The status pane indicates if the proj ector is used with an allowed rotation.
14. Ser vice 2. Use the ▲ or ▼ key to select the desired internal service pattern and press ENTE R to open a selection menu. Input patterns Input items in t he Internal Service Patterns menu are only shown when the corresponding slot contains an input boar d.
14. Service Osd patter ns Image 14-41 Internal service patterns, OS D Press ENTER to display the list of possi ble patterns. Image 14-42 OSD T est patterns Pmp out patt erns Image 14-43 Internal service patterns, Pm p Out Press ENTER to display the list of possi ble patterns.
14. Ser vice Image 14-44 Pmp out test patterns T o change the options for the selected pat tern, use he ► key to open these options. The num ber of options can change for the diff erent patterns.
14. Service 14.5 Convergence What can be done? The convergence patterns can be used to c heck the convergence alignment of red, green and blue. If there is a m isalignment of at least one 1 pixel, an electronic realignment is possible. Mechanical realignment of the convergence can only be done by a quali fi ed service technician.
14. Ser vice Image 14-52 4. Use the ▲ or ▼ key to adjust vertical and the ◄ or ► key to adjust ver tical convergence. Adjust until the crossi ng of the center Green ( Red) convergence pattern coincide with t he diagonal l ine of the center Blue c on- vergence pattern.
14. Service Image 14-55 Factory defaults, settings By default the following settings are excluded - IP address - Serial settings - DMX s et ti ngs - Electronic convergence - Standby settings - Scheduler tasks 2. If you w ant to restore also one of the items in the list, check the check box in front of that item.
14. Ser vice Image 14-58 USB memory selectio n 2. Select Save Custom S ettings and press ENT ER to download t his set. Note: Make sure a formatted USB sti ck is inserted in the USB c onnector . When no USB stick is available, a message will be shown: No USB device is found.
14. Service 14.8 Reset Formatter Why and w hen A reset formatter is necessary when e.g. a color is missing, artifacts are visi ble in the image or image is frozen and the formatter test patterns cannot be displayed. How to reset 1. Press Menu to activate the menus and select Service → Reset Form atter .
14. Ser vice Image 14-66 Main me nu, se rv ice Image 14-67 Service, re fi ll mode 2. Press EN TER to select. U se the ▲ or ▼ key to select Ye s .o r No and pr ess ENTE R . Image 14-68 If you want to start the re fi ll mode, select Ye s . If you do not want to start the re fi ll mode, select No .
14. Service Image 14-69 Main me nu, se rv ice Image 14-70 Service, save custom settings 2. Use the ▲ or ▼ key to select Ye s an d press ENTER . Image 14-71 Save custom settings, question 14.
14. Ser vice Image 14-72 Main me nu, se rv ice Image 14-73 Service, spec ial HD camera mode 2. Press ENTER to t oggle between [On] and [Off] . 14.12 Auto Dimming when ove r-temperature What can happen? When an over-temperature is detected, the projector st arts dimming the lamp so that the projector can cool down.
14. Service 14.13 T ime and Date How to set 1. Press Menu to activate the menus and select Servi ce → Time and Date . Image 14-76 Main me nu, se rv ice Image 14-77 Service, t ime and date Image 14-78 Date and time set up 2. Use the ▲ or ▼ key to select Hour , Minute , Day , Month or Y ear and press ENTER to select.
14. Ser vice 290 R5905032 HDX SERIES 02/03/2015.
15. Mainte nance 15. MAI NTENAN CE About this chapter This chapter cont ains general maintenance procedures. Overview • Cleaning the lens • Cleaning the exterior of the projector 15.
15. Mainte nance 292 R5905032 HDX SERIES 02/03/2015.
16. Ser vicing 16. SER VICING About this chapter This chapter contains general servicing procedures like lamp hous e replacement, input unit replacement etc.
16. Ser vicing 1 Image 16-2 Fixate i nput 16.2 Removal of the lamp house W ARNING : Switc h off th e proj ector a nd unpl ug th e power cor d befo re st arti ng t he procedu re. Necessary t ools Flat screwdriver How to remove 1. Remov e the lamp cover on the input s ide, see "Removal of the lamp cover", page 299.
16. Ser vicing Image 16-3 Lamp house, captive screws 3. T ake the lamp house by both handles and pull it out. Image 16-4 Lamp house, remov al 16.3 Installation of the lamp house W ARNING : Switc h off th e proj ector a nd unpl ug th e power cor d befo re st arti ng t he procedu re.
16. Ser vicing How to install 1. T ake the lamp house by its handles and gently slide the lamp house into its socket. Note that the compartment is provided with a guide (1) to position the lamp house correctly . 1 2 2 1 6 3 3 2 5 3 4 4 Image 16-5 Insert lamp house 2.
16. Ser vicing How to remove 1. Remov e the lens. See "Lens remo val", page 30. 2. Remov e the rubber dust ring from the lens holder . Image 16-6 Dust ring removal 3. Release the 4 captive screws (1). 1 Image 16-7 Front cov er removal 4. T ake of f the front cover .
16. Ser vicing 16.5 M ounting the front cover W ARNING : Switc h off th e proj ector a nd unpl ug th e power cor d befo re st arti ng t he procedu re. Necessary t ools 7m m fl at s crew driver How to mount 1. Place the front cover with the rubber dus t faci ng the projector on its place.
16. Ser vicing Image 16-9 Mount dust ri ng 4. Mount lens again. 16.6 Rem oval o f the la mp co ver W ARNING : Switc h off th e proj ector a nd unpl ug th e power cor d befo re st arti ng t he procedu re. Necessary t ools 7m m fl at s crew driver How to remove 1.
16. Ser vicing 1 1 Image 16-10 Lamp side cover 2. T ake of f the side cover . 16.7 Mounting the lamp cover W ARNING : Switc h off th e proj ector a nd unpl ug th e power cor d befo re st arti ng t he procedu re. Necessary t ools 7m m fl at s crew driver How to mount 1.
16. Ser vicing 1 1 Image 16-1 1 Lamp side cover 16.8 Replacement of the high density dust fi lter C AUTION : The high density fi lter must be replaced on a reg ular basis, depending on the environment condi- ti ons of the project or . W ARNING : Switc h off th e proj ecto r and un p lug the power cord before starting the procedure.
16. Ser vicing Image 16-12 Filt er replac ement 3. T ake out the fi lter and insert a new one. C AUTION : Never clean the fi lter Always replace with a n ew one. 16.9 Remove and clear metal f ront fi lter W ARNING : Switc h off th e proj ector a nd unpl ug th e power cor d befo re st arti ng t he procedu re.
16. Ser vicing 1 Image 16-13 4. At the same time, take out the fi lter . Clean the dust fi lter 1. Remov e most contamination with a vacuum cleaner . 2. Blow remaining du st away with compressed air in an o ther room or outside. If you cannot clean the fi lter anymore, insert a n ew one.
16. Ser vicing 304 R5905032 HDX SERIES 02/03/2015.
A. Dimens ions A. DIMENSIONS Overview • Dimen sions of a HDX projector A.1 Dimensions of a HDX projector Overview 725 CG2 373 383 413 475 CG1 CG0 Center of gravity Center of gravity Image A-1 Dimensions , mm Geometrical centre Centre without lens Centre with lens CG0 186.
A. D imensions 306 R5905032 HDX SERIES 02/03/2015.
B. Sp ecificatio ns B. SPECIFICA TIONS B.1 Speci fi cations of the HDX W12 Overview Projec tor t ype WUXGA 3-chip DLP digital projector T echnology 0.
B. Spec ific atio ns Po wer consu mption 2,300 W / STBY <8 W Noise level (typi cal at 25°C/77°F) 49 dB (A) Operating temperature 0 ~ 40°C / 32 ~ 104°F operat ion hu midi ty no c ondens 0-8 0 % Dissipati on BTU max. 7,848 BTU/h Dimensio ns (WxLxH) 475 x 725 x 382 mm (18.
B. Sp ecificatio ns Opti onal Inp uts 5- BNC RG BHV ( RGBS /RGsB, YUV CS/SO Y , Com posite video, S-Video); DVI - I (HDCP including analog RGB YUV) + BarcoLink/SD I/HDSDI/dual HDSDI/3G; 3D active input input(HDMI/Displ ayPort) feat.
B. Spec ific atio ns Picture-in-picture T wo s ources simultaneously Orien tat ion t able - ceiling - side (portrait)* - vertical * lamp door down/bottom DMX 512 Standard W ARP direct adjust OSD + too.
B. Sp ecificatio ns Optical lens shift Ver tical: -30% to +120% / Horizontal: -40% to +40% on zoom lenses (memorized) Color correction P7 Lamps 2.5 kW Xenon Lamp lifetime (typical) 1,000 hours T ransp.
B. Spec ific atio ns B.5 T echnical Regulations Certi fi cate s Image B-1 EAC mark 10 Image B-2 Rohs RoHS Image B-3 Rohs OK Image B-4 CE mar k 312 R5905032 HDX SERIES 02/03/2015.
C. Stan dard source fil es C. ST ANDARD SOURCE FILES C.1 T able ove rview Ta b l e o v e r v i e w The following standar d image fi les are pre-programmed in the projector .
C. Sta ndard sour ce file s Name 6 Fvert Hz 7 FHor kHz 8 Fpix MHz 9 Ptot 10 Pact 11 Ltot 12 Lact 13 1280x1024@85 85,027 91,149 157,506 1728 128 0 1072 1024 1360x768@60 60,15 47,752 85,500 1792 136 6 7.
C. Stan dard source fil es Name 6 Fvert Hz 7 FHor kHz 8 Fpix MHz 9 Ptot 10 Pact 11 Ltot 12 Lact 13 hd-1920x1080@30i 60,000 33,750 74,250 2200 192 0 562 540 hd-1920x1080@30p 30,000 33,750 74,250 2200 192 0 1 125 1080 hd-1920x1080@29,97i 59,94 33,716 74,176 2200 1920 56 2 540 hd-1920x1080_2@25i 50,000 31.
C. Sta ndard sour ce file s 316 R5905032 HDX SERIES 02/03/2015.
D. DMX chart D. DMX CHART Overview • DM X chart, Basic • DM X chart, Full • DM X chart, Extended D.1 DMX chart, Basic Overview Chan- nel Funct ion Va lue Default Act ion 0 - 5 Mechanical shutter.
D. DMX chart Chan- nel Functi on V alue Default Actio n 0 - 87 No function 88 - 95 Input 1 (if held for 2 seconds) 96 - 103 Input 2 ( i f held for 2 seconds) 104 - 1 1 1 I nput 3 (if held for 2 second.
D. DMX chart Chan- nel Funct ion V alue Default Acti ons 0 - 87 No function 88 - 95 Input 1 (if held for 2 seconds) 96 - 103 Input 2 (if held for 2 seconds) 104 - 1 1 1 Input 3 (if held for 2 seconds).
D. DMX chart 320 R5905032 HDX SERIES 02/03/2015.
E. Stack ing HDX proj ectors E. ST ACKING H DX PROJECTORS Overview • Mo unt stacking poi nts • Stacking HDX projectors • Aligning stacked HDX projectors E.1 Mount stacking points Necessary t ools A l l e nk e y8m m How to mount 1. Place the fi rst stacking point on a corner .
E. St acking H DX pro jectors How to stack 1. Mount stacking points on lower projector . See "Moun t stacking points", page 321. 2. Mount a bottom carry handle on the upper projector . See "Mounting the bottom c arry handler", page 39.
E. Stack ing HDX proj ectors Image E-4 Securi ty cables, mou nt 2. Mount the other end of the security cable around the carry handle of the top projector and c lasp the safety hook r ound the cable as illustrated. Make sure that the falli ng distance is maximum 20 cm.
E. St acking H DX pro jectors W ARNING : Never open an interlocking adapter o f a stacked proj ector which is sti ll suspended. F irst p lace the stacked projectors on the fl oor . E.3 Aligning stacked HDX projectors Necessary t ools No tools. How to align stacked projec tors 1.
E. Stack ing HDX proj ectors Inclination Image E-7 Stacked projectors, inclination 5. If necessary , adjust the skew of the stacked projector wit h respect t o the ref erence projector by turning the Hand screw in or out. The hand s crew is located at smallest side of the carrying handle (front or back).
E. St acking H DX pro jectors Zoom Image E-10 Stacked projector , zoom 8. If necessary , repeat from step 2 until the hatch pattern of the s tacked projector is perfectly aligned with t he hatch pattern of the reference projector .
F. Envir onmental inf ormation F . ENVIRO NM ENT AL INF ORMA TION Overview • Dispos al information • Rohs com pliance • Production address • Importers contact information F .
F. Envir onmental inf ormation T able of toxic and hazardous substances/elements and their content, as required by China’ s management methods for controlling pollution by el ectronic infor mation p.
F. Envir onmental inf ormation T ur key RoHS comp liance Türkiye Cumhuriyeti: AEEE Yönetmeli ğ ine Uygundur . [Republic of T urkey: In conformity with t he WEEE Regulation] F .3 Production a ddress Factories Barco NV Noordlaan 5, B-8520 Kuurne ( BELGIUM) Barco Visual (Beijing) Electronics Co.
F. Envir onmental inf ormation 330 R5905032 HDX SERIES 02/03/2015.
Index INDEX Numerics/ Symbols 3D 93, 96–101, 21 1, 214–215 3D sync out, inv ert 101, 215 Auto detection 9 7 Dark time 21 1 Field dominance 100 Input type 98 Invert 3D sync out 101, 215 Modes 93 Ou.
Index Power cable 38 Power net 38 Connections 50, 53 Communication 50 Utility-Accessory O utlet 53 Contrast adjustment 106 Contrast enhancement 194 Convergence 281 Cooling liquid circuit warning 9 Coo.
Index File services 123 Image services 123–128, 130 Copy 128 Delete all fi le 126 Delete custom fi le 125 File load fi lter 124 File manipulations 123 Files 123 Manual load fi le 123 Option auto.
Index Main window 136, 138 Position 138 Size 136 Source sele ction 136 Overview 135 PIP 140–143 Activation 140 Position 143 Size 142 Source sele ction 141 PiP window 139 Layout fi le services 145.
Index Common 221 Controlling 63 Individual 220 Projector con fi gurations 16–17 Front projection 16 Rear projection 17 Projector control 2 19–226, 228–230, 232–234, 236–238, 240– 243, 245.
Index SDI con fi guration 79 Serial comm unicati on 51, 222 Baud rate 222 Interface s tandard 222 Service 267–270, 272, 274–277, 281–283, 285–289 Auto dimming 288 Over-temperature 288 Converg.
Index Z Z-axis, current light output 162 R5905032 HDX SERIES 02/03/2015 337.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Barco W18 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Barco W18 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Barco W18 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Barco W18 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Barco W18, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Barco W18.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Barco W18. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Barco W18 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
