Manuale d’uso / di manutenzione del prodotto 1500 del fabbricante Sun Microsystems
Vai alla pagina of 15
Sun Microsystems, Inc. 4150 Network Circle Santa Clara, CA 95054 U .S.A. 650-960-1300 Send comments about this document to: docfeedback@sun.com Sun Blade™ 1500 Ser vice , Diagnostics , and T roub leshooting Manual Pa r t No .
Chapter 11 Replacing the Motherboard and Associated Components 11-3 FIGURE 11-1 DIMM Location and Identification Depending upon the configuration of your workstation, you can either add or replace memory . In either case, the new DIMMs must meet the Sun workstation requir ements.
Chapter 13 Replacing Chassis Components 13-15 Y ou can also view an animated version of these instructions by clicking on this film icon. 13.3.1 Identifying the Rear Fan The front and r ear fans on the Sun Blade 1500 workstation are contained in green brackets.
12-16 Sun Blade 1500 Service, Diagnostics, and Troubleshooting Manual • April 2003 FIGURE 12-13 Smart Car d Reader Location and Identification 12.3.2 Removing the Smart Car d Reader 1.
Chapter 14 Replacing Internal Cables 14-7 14.2.1 Identifying the DVD-ROM Drive Interface Cable The DVD-ROM has separate power and interface cables. The power cable is a Y cable that connects to the motherboard at IDE PWR and the other ends to the hard drives and DVD-ROM drive.
Chapter 14 Replacing Internal Cables 14-15 3. Disconnect the IDE power cables from the upper hard drive HDD0 . See FIGURE 14-12 . FIGURE 14-12 Disconnecting the IDE Power Cable Fr om the Hard Drive(s) 4. If installed, disconnect the IDE power cable from the lower hard drive HDD1 .
14-10 Sun Blade 1500 Service, Diagnostics, and Troubleshooting Manual • April 2003 14.3 Replacing the Har d Drive Interface Cable This section describes removal and installation of the hard drive interface cables.
Chapter 11 Replacing the Motherboard and Associated Components 11-5 FIGURE 11-3 Pressing the Catch on the Rear Fan Bracket 4. Slide the duct up until it is f lush with the edge of the rear fan bracket. See FIGURE 1 1-4 . FIGURE 11-4 Sliding the Duct Up 5.
Chapter 10 Preparing to Replace Components 10-15 FIGURE 10-9 Bezel Location and Identification 3. Release the lower mounting tabs. Carefully move the lower pair of mounting tabs apart, and then push them forwar d slightly .
11-16 Sun Blade 1500 Service, Diagnostics, and Troubleshooting Manual • April 2003 FIGURE 11-15 Pr essing Down on the Clip Latch b. Slide the clip to unhook the end opposite the latch. This relieves clip pr essure. c. Rotate the clip away from the CPU fan and heatsink assembly and lift it off the locking ring.
11-22 Sun Blade 1500 Service, Diagnostics, and Troubleshooting Manual • April 2003 1 1.3.1 Identifying the Battery FIGURE 1 1-23 shows the location of and identifies the battery . FIGURE 11-23 Battery Location and Identif ication T ABLE 1 1- 1 lists the battery specifications.
11-36 Sun Blade 1500 Service, Diagnostics, and Troubleshooting Manual • April 2003 FIGURE 11-34 Identifying the PCI Car d Slots 3. Swing out the PCI card support. Squeeze the inside tabs together and swing the PCI card support out. See FIGURE 1 1-35 .
Chapter 11 Replacing the Motherboard and Associated Components 11-45 FIGURE 11-42 Removing Cables Fr om the Routing Clips 9. Disconnect the power and signal cables. Disconnect the following power and signal cables from the corresponding motherboard connectors and set them out of the way of the motherboard.
Chapter 13 Replacing Chassis Components 13-45 FIGURE 13-48 Removing the PCI Car d Support Note – Do not use the chassis cross brace as a handle. Proceed to “Installing the PCI Card Support” on page 13-45. Note – Do not operate the workstation without the PCI card support installed.
Chapter 15 Finishing Component Replacement 15-9 FIGURE 15-8 Reconnecting the Keyboard, Mouse, Monitor , and Network Connections 2. Reconnect any other external peripherals.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Sun Microsystems 1500 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Sun Microsystems 1500 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Sun Microsystems 1500 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Sun Microsystems 1500 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Sun Microsystems 1500, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Sun Microsystems 1500.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Sun Microsystems 1500. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Sun Microsystems 1500 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
