Manuale d’uso / di manutenzione del prodotto R 9849999 del fabbricante Barco
Vai alla pagina of 18
R 9849999 INSTALLATION MANUAL Ceiling Mount for CLM series projector Date 26/11/07 Rev: 00 Art. No.: R 59770182.
Due to constant research, the information in this manual is subject to change without notice. Produced by BARCO NV,Nov. 2007. All rights reserved. Trademarks are the rights of their respective owners. BARCO n.v. Noordlaan 5 B-8520 Kuurne Belgium Tel : +32/56/368211 Fax : +32/56/351651 E-mail : sales.
Safety guidelines WHO WARNING CAUTION PRODUCT CARE This installation manual must be performed by authorized technical personnel only. The ceiling should be capable of supporti ng a weight of at least 5 times the total weight of the Ceiling Mount and Projector (i.
Description and Contents of the kit Purpose of the Kit The kit is designed for the CLM CM R10 series projectors and allows the projector to be mounted to the ceiling.
Remark: The ceiling mount can also be mounted us ing one of the 2 available bars (height adjustment) and cable cover assy. R9841260: short bar R822922 a nd cable cover assy . min length = 445mm(17.52 inch) max length = 810 mm(31.89 inch) R9841261: long bar R822923 cable cover kit R984 .
Mounting the Assembly Necessary Tools 1. Torx screw driver for M3 screw 2. Hexagonal driver (n° 6) 3. Ring spanner 12-13mm 4. Side spanner 12-13mm 5. Cross head screw driver for M8 screw Centering the ceiling mount Mark the position on the ceiling hole.
Mounting the Assembly The fixation can be done with standard M8 bolt (not supplied ).
Projector preparation 1. Turn the projector to its back and remove the Feet assembly. Unscrew 3 Plastic feet and remove their Allen head M10 screws. Discard 3 plastic feet r852944 and x head M10 screw. R852944, R852945 & A566050 M10 SCREW, & FEET SUPPORT 2.
3. Lift and slide the projector assembly in to the Ceiling mount. The projector will be located precisely into the ceiling m ount base plate after the tightening of 3 M 8 flange Nuts (b360623). Slide Lift 4. Route the Signal cables and Po wer cord into the cable saddles.
Adjustments Following adjustment can be done in random order. Shift parallel to screen 1. Shift parallel to the screen Loosen the 2 bolts A and move the projec tor till the projector is aligned. Tighten these 2 bolts to secure the position. 2. Up down Tilt Loosen the 4 bolts B .
F vertical axis ±5° E Rotate around Rotate around central Axis ±3° G F.
3. Rotate around central Vertical axis Loosen the 4 bolts E . Rotate/adjust the pr ojector clockwise or anti clockwise. Tighten the 4 bolts E to secure the position. 4. Rotate around central Horizontal axis Loosen the 4 bolts F . Adjust the motion precisely by moving bolt G clockwise or anti clockwise.
Mounting the bar with Cable Cover assembly 1. Unscrew the 2 bolts J and slide out the upper part of the Ba r. Pass the cable cover into the upper part of the Bar 2. Slide the horizontal shift plate R 826743 into the lower part of the Bar. Fix with 4 M8 bolt K.
4. Routing the Cables a. RGBHV cable preparation : With the help of PVC tape arrange the connectors in series. Pass the Signal cables and Power cord into cable guide R826761 . b. Pass the Signal cables into the IQ bar assembly from top side. Take out the BNC connector (in case of a 5 B NC cable) one by one from bottom side.
c. Pass the Power cord and the ot her cables (if any) one by one. d. Pass all the cables one by one from cable guide R 826745 and fix the cable guide on to the horizontal sh ift plate using 2 M3 Screws L. L The cable routing through IQ bar is complete.
6. Hang on the IQ bar and cable routed assembly. Fix with 4 M8 bolt along with washer M. M 7. Mount the Ceiling mount assembly on to the horizontal shift plate by twisting and then lifting up. Fix the 2 M8 Bolt A. A 8. Route the Power cord to the back and Signal cables to the front.
There is also an option to route the c able from inside the Ceiling mount using cable ties and guiding holes on the Ce iling mount base as shown below.
9. The adjustment proce dure for the rotation around central vertical axis can also be done as explained below. Loosen the 4 M3 screws N of cable cover and slide it down word. Loosen the 4 bolts O. Rotate /adjus t the projector clockwise or anti clockwise.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Barco R 9849999 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Barco R 9849999 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Barco R 9849999 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Barco R 9849999 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Barco R 9849999, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Barco R 9849999.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Barco R 9849999. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Barco R 9849999 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
