Manuale d’uso / di manutenzione del prodotto F144 del fabbricante Stoelting
Vai alla pagina of 37
Futura F144 and F131 w/ Blender OWNER'S MANUAL Manual No. 513603-1 March 2005.
.
Need Part s or Service? We stock the parts you need. Our Technicians are factory trained and are certified in the Stoelting Technicare program. Model No.: _______________________ Serial No.: _______________________ Purchase Date: ____________________ Start-Up Date:____________________ CALL Distributor: _________________________ Phone No.
.
This manual provides basic information about the freezer . Instructions and suggestions are given covering its operation and care. The illustrations and specifications are not binding in detail.
.
Safety Alert Symbol: This symbol Indicates danger , warning or caution. Attention is required in order to avoid serious personal injury . The message that follows the symbol contains important information about safety .
.
T ABLE OF CONTENTS SECTION 1 - SPECIFICA TIONS .................................................................................. 1 1.1 Description .......................................................................................................
Fig. Description Page 1 Model Endura/Futura 131G Freezer ................................................................... 1 2 Specifications .................................................................................................... 1 3 W arning Label Locations .
1 1.1 DESCRIPTION The Stoelting Futura F144 and F131 w/ Blender countertop combination shake/softserve freezers are gravity fed. The freezers are equipped with fully automatic controls to provide uniform product.
2 1.2 SPECIFICATIONS MODEL FUTURA 144 COUNTERTOP COMBINATION SHAKE/SOFTSERVE GRAVITY FREEZER Dimensions: Freezer: 22" (56 cm) wide x 28" (72 cm) deep x 34.75" (88 cm) high Crated: 28" (71 cm) wide x 35 1/2" (89.4 cm) deep x 40.
3 SECTION 2 INSTALLATION INSTRUCTIONS 2.1 SAFETY PRECAUTIONS Do not attempt to operate the freezer until the safety precautions and operating instructions in this manual are read completely and are thoroughly understood. T ake notice of all warning labels on the freezer (Fig.
4 Fig. 4. Space and Ventilation Requirements 2.2 SHIPMENT AND TRANSIT The freezer has been assembled, operated and in- spected at the factory . Upon arrival at the final destina- tion, the complete freezer must be checked for any damage which may have occurred during transit.
5 Fig. 7. Floor Stand 2.4 FLOOR ST AND INST ALLA TION T o install the F144 on the floor st and, follow the step s outlined below . 1. Uncrate the floor stand and place in an upright posi tion. NOTE Detailed instructions are included with each floor stand.
6.
7 3.1 OPERA T OR'S SAFETY PRECAUTIONS SAFE OPERA TION IS NOT AN ACCIDENT ; Observe these rules: A. Know the freezer . Read and underst and the Operating Instructions. B. Notice all warning labels on the freezer . C. Wear proper clothing. A void loose fitting garments , and remove watches, rings or jewelry which could cause a serious accident.
8 WARNING High voltage will shock, burn or cause death. The OFF-ON switch must be placed in the OFF position prior to disassembling for cleaning or servicing. Do not operate machine with cabinet panels removed. B. OFF-ON SWITCH The OFF-ON switch is a two position toggle switch used to supply power to the control circuit.
9 L. BLENDER POWER SWITCH (F131 Models Only) The blender power switch is a two position toggle switch used to supply power to the blender . When the switch is in the OFF position, the agitator will not turn. When the switch is in the ON position, the agitator will be activated every time the blender activation switch is pressed.
10 Figure 13. Sanitizing Hopper Figure 14. Spigot Opened and Solution Draining D. Clean sides of hopper , mix inlet regulator and under- side of hopper cover using a sanitized soft bristle brush dipped in the sanitizing solution (Fig.
11 G . After about 6 to 10 minutes the freezer will shut off and the green lens will illuminate. The product will be ready to serve. Freeze down time may be longer for some frozen diet dessert mixes. High ambient temperatures may extend freeze down time.
12 B. Place the OFF-ON rocker switch in the ON position and push the CLEAN switch to rotate the auger . Allow the mix to agitate in the freezer barrel until the mix has become a liquid, about 5 minutes. C. Drain the liquid mix by opening the spigot. A bucket or container should be placed under the spigot to catch the liquid mix (Fig.
13 Figure 20. Auger Flight Wear and Front Auger Support Bushing Wear D. Place the OFF-ON switch in the OFF position. T o disassemble the freezer , refer to the following steps : A. Remove the mix inlet regulator from the hopper by pulling straight up.
14 J . Remove the rear seals. K. Remove all O-rings from parts by first wiping off the lubricant using a clean paper towel. Then squeeze the O-ring upward with a dry cloth (Fig. 25). When a loop is formed, roll out of the O-ring groove. CAUTION Do not use any type of sharp object to remove O- rings.
15 D. Screw the springs onto the studs in plastic flights. Springs must be screwed into the flights com pletely to provide compression (Fig. 26). CAUTION Do not place the mix inlet regulator into the hopper before inst alling the auger . Attempting to inst all the auger with mix inlet regulator in place will damage the mix inlet regulator .
16 3.12 ROUTINE CLEANING T o remove spilled or dried mix from the freezer exterior , simply wash in the direction of the finish with warm soapy water and wipe dry .
17 3. SANITIZING – After the machine has been cleaned and contains no milkstone, the machine is reassembled. Then a FDA approved sanitizing solution is run through the machine to kill bacteria.
18 D. QUARTERLY W ARNING High voltage will shock, burn or cause death. Turn off and lock out main power disconnect before servicing. Do not operate machine with cabinet panels removed. The air-cooled condenser is a copper tube and aluminum fin type. Condensing is totally dependent upon airflow.
.
20.
21 SECTION 4 TROUBLESHOOTING CHARTS M E L B O R P E S U A C E L B I S S O P Y D E M E R s e o d r e z e e r F . n u r t o n . f f o s i r e z e e r f o t r e w o P . 1 . d e p p i r t r o n w o l b f i t i u c r i c r o e s u F . 2 . ) n r u t t o n l l i w r e g u a ( p u - e z e e r F .
22 s e o d t c u d o r P . e s n e p s i d t o n . r e p p o h n i x i m o N . 1 s i e b u t r o t a l u g e r t e l n i x i M . 2 . d e g g u l p d e d e e n r o t a l u g e r t e l n i x i m l a i c e p S . 3 . d e s u g n i e b x i m r o f g n i e b s i r e z e e r f f o y t i c a p a C .
23 ERROR CODE SYSTEM *Refer to Page 19 for Troubleshooting. ** If the Clean switch is operated three times within 10 seconds, this will cause the Push-T o-Freeze light to flash and the clean function will be disabled for 10 minutes. The power switch must remain on or the 10 minute timer will not time out.
24.
25 SECTION 5 REPLACEMENT PARTS 5 . 1 HOW TO ORDER PARTS To assure receipt of the proper replacement parts, supply your dealer or distributor with the following information: A . Model number of equipment. B . Serial number of model, stamped on nameplate.
26 Item No. Part No. Description Qt y . 1 2183047 Front Door Only 1 2177072 1.5" S pigot Extension 2177073 2.5" S pigot Extension 2177074 3" S pigot Extension 2 482019 Circular Door Kno.
W ARRANTY SOFT SER VE / SHAKE FREEZERS 1. Scope: Stoelting, LLC warrants to the first user (the “Buyer”) that the freezer cylinders, hoppers, compressors, drive motors, speed reducers, auger and a.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Stoelting F144 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Stoelting F144 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Stoelting F144 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Stoelting F144 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Stoelting F144, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Stoelting F144.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Stoelting F144. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Stoelting F144 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
