Manuale d’uso / di manutenzione del prodotto GALAXY NW-12 del fabbricante Barco
Vai alla pagina of 35
PMP kit Install ation manual Galaxy NH-1 2, NW-12, G alaxy NW -12 R7649672K R7649676K R59770498/01 28/02/2011.
Barc o nv Simulation D ivision Noordlaan 5, B-8 520 Kuurne Phone: +32 56.36.82.11 Fax: +32 56.36.84.86 E-mail: info@barco.com Visit us at the web: www.
Changes Barco provides this manual ’as is’ without warranty of any kind, either expressed or implied, including but not limited to the implied war- ranties or merchantability and fi tness for a particular purpose.
.
Tabl e of c ont ents T ABLE OF C ONTENTS 1 . S a f e t y i n s t r u c t i o n s ...... .... .... ...... .... ...... .... ...... .... ...... .... ...... .... .... ...... .... ...... .... ...... ... 3 1 . 1 S a f e t y d u r i n g k i t i n s t a l l a t i o n .
Tabl e of co nt ents 2 R59770498 PMP KIT 28/02/2011.
1. Safety ins tructions 1. SAFETY INSTRUCTIONS 1.1 Safety during kit installation W ARNING : The pro cedures be low may on ly be per formed b y Barco tr ained a nd quali fi ed technicians. W ARNING : Power down the pr oject or and remove the powe r cord form the wall ou tle t before re moving any of the projector covers.
1. Safety ins tructions 4 R59770498 PMP KIT 28/02/2011.
2. PMP k it 2. PMP KIT 2.1 Introduction Introduction In case of failure of a PMP , it must be replaced by a (blank) new one. However , since mos t of the projector related data is stored on this board, this data will be lost while replacing the board.
2. PMP ki t 6 R59770498 PMP KIT 28/02/2011.
3. Kit ins tal latio n (det ail ed) 3. KIT INST ALLA TION (DET AILED) C AUTION : Thi s procedu re may only be per formed by Bar co trai ned and qual i fi ed technicians. 3.1 Mak ing a backup of the PMP to be replaced Introduction If a PMP fails, communication via Ethernet is most probably still possible.
3. Kit instal lation ( detailed ) 3. L ift the pr eformatter unit a bit and unplug the following connectors: - J100, J101, J102 on the preformatter: data from the PM P - J1 1 on the preformatter: power supply from the power box - J410 on the PMP : commands from the local keypad - J13 on the PMP: commands from the I R receiver 4.
3. Kit ins tal latio n (det ail ed) How to remove the PMP? 1. R emove the input module (see concerning chapter) 2. R emove both screws fi xing the PMP to the front plate Image 3-4 PMP: front fi xing screws 3. R emove the side screws fi xing the input boards to the PMP Image 3-5 4.
3. Kit instal lation ( detailed ) Image 3-7 PMP: fi xing screws of the L VDS interface 6. R emove the screws fi xing the PMP fan assembly to the PMP Image 3-8 PMP fan assembly: fi xing screws (1) Image 3-9 PMP fan assembly: fi xing scr ews (2) 3.2.
3. Kit ins tal latio n (det ail ed) Image 3-12 PMP: fi xing screws of the L VDS interface 3. C onnect the PMP to the inputs by plugging in the board-to-board connectors Image 3-13 PMP: plug int o the input board con nectors 4. F ix the PMP to the input boards using the side screws Image 3-14 PMP: side screws fi xing the input boa rds 5.
3. Kit instal lation ( detailed ) Image 3-15 PMP: front fi xing screws 6. ins tall the input module into the projector (see concerning chapter) 3.2.4 Installing the input module Necessary t ools T orx s crewd river T10 How to install the input module? 1.
3. Kit ins tal latio n (det ail ed) Image 3-17 input m odule: fi xing front screws 4. P ut the preformatter unit next to its correct position and pl ug in the connectors: - J100, J101, J102 on the pr.
3. Kit instal lation ( detailed ) Necessary t ools Computer or laptop, connected to the pr ojector through Ethernet How to upgrade the p rojector software? 1. E nter the correct Ethernet sett ings in the OSD of the projector 2. D ownload the desired upgrade tool to your computer or laptop 3.
A. Backu p and restor e data A. BACKUP AND RESTORE DA T A Overview • Connecting to the projector through Projector Support • Ma king a backup of the projector ’s key data • Restoring a set of k ey data About this chapter It i s extremely important to make backups of your project or data after each sett ing change.
A. Backup and re stor e data Image A-1 Projec tor Support tool: user interface 4. In the Communic ation Parameters section, enter the IP address or the hostnam e of the projector Image A-2 Proje ctor .
A. Backu p and restor e data Tip : Y ou can also press the Query butt on. A list appears, showing all the projectors that are connected to the same network.
A. Backup and re stor e data Select it and hit OK to open a new window where the network setti ngs can be m anually changed. It is advised to switch DHCP to On to continue. Image A-6 Projec tor Suppor t tool : change DHCP sett ing to O N Image A-7 Proje ctor Support to ol: con fi rm ne two rk se tting s A.
A. Backu p and restor e data Image A-8 Projec tor Support t ool: sele ct browse in the Backup section 2. Select a target folder on the computer to save the backup of the projector data Image A-9 Projec tor Support tool: browse to the backup fol der 3.
A. Backup and re stor e data Image A-1 1 Proje ctor Support tool : start th e backup of all settings 5. Wait for the backup pro cess to be fi nished. Image A-12 Proje ctor Support tool: progr ess bar A successful backup i s indicated by a green oval.
A. Backu p and restor e data C AUTION : I t is not allowed t o do any manua l chang e to a bac kup fi le. A changed fi le cannot be rest ored! A.3 Restoring a set of key data C AUTION : If a backup .
A. Backup and re stor e data Image A-15 Projec tor Support tool: browse to the backup fol der 4. In the Res to r e section, you can select an option (not requir ed): - Overwrite serial number - Ov erwrite device typ e Image A-16 5. In the Restore section, hit A ll settin gs Image A-17 Proje ctor Support tool : start th e restore of the backup 6.
A. Backu p and restor e data Image A-18 Projec tor Support tool : con fi rm the restore of the backup 7. Wait for the res tore process to be fi nished Image A-19 Projector Support t ool: progr ess bar Image A-20 Projector Suppo rt tool: reboot of the PMP after the restore A successful restore of the ba ckup fi le is indicated by a gree n oval.
A. Backup and re stor e data Image A-21 Proje ctor Support t ool: restore of the ba ckup was successf ul An error during the restore of the backup fi le is indicated by a brief description and a red oval.
A. Backu p and restor e data Image A-22 Proje ctor Support T ool: restor e of the backup was not s uccessful H o wt or e s t o r et h ek e yd a t ai nan e wP M P ? It is assumed that an or iginal backup fi le is available (zip format).
A. Backup and re stor e data Image A-23 Projec tor Support tool: query list Tip : If more then one PMP without serial number is listed, the MAC address must b e checked. O n the PMP board a label mentioning the MAC address can be found near the power connector on the same side as the heatsinks.
A. Backu p and restor e data Image A-24 Proje ctor Support tool: hit browse in th e restore sec tion 4. B rowse to the fol der on the computer where the backup fi le is stored 5. S elect the backup fi le and hit Open 6. In the Restore section, hit A ll settin gs Image A-25 Projec tor Support tool: browse to the backup fol der 7.
A. Backup and re stor e data Image A-26 Projec tor Support too l: overview of the fi les that will be restore d 8. Wait for the res tore process to be fi nished Image A-27 Projector Support t ool: p.
A. Backu p and restor e data A successful restore of the backup fi le is indicated by a green oval, and t he original serial nu mber will be dis played in the Projector identi fi cation section of the user interface. Image A-29 An error during the r estore of the backup fi le is indicated by a brief descript ion and a red oval.
A. Backup and re stor e data 30 R59770498 PMP KIT 28/02/2011.
Index INDEX B backup 7, 15, 18 making of 18 PMP 7 D description 5 kit 5 I input module 7, 12 installing 12 remo ving 7 installation 5, 7 kit 5, 7 installing 1 0, 12 input module 12 PMP 10 introduction.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Barco GALAXY NW-12 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Barco GALAXY NW-12 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Barco GALAXY NW-12 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Barco GALAXY NW-12 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Barco GALAXY NW-12, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Barco GALAXY NW-12.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Barco GALAXY NW-12. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Barco GALAXY NW-12 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
