Manuale d’uso / di manutenzione del prodotto DP-1200/DP-1500/DP-2000 R59770175/01 del fabbricante Barco
Vai alla pagina of 27
Xenon bulb lamp r eplac ement Install ation manual F or DP-12 00/DP-150 0/DP-20 00 R59770175/01 24/09/2008.
Barco NV Media and En t ertainment Division 11101 Trade Center Drive, Rancho Cordova, California 95670, USA Phone: +1 916 859-2500 Fax: +1 916 859-2515 E-mail: folsomsales@barco.com Visit us at the web: www.barco.com Barco n v Media & Entertainment D iv ision Noordlaan 5, B-8 520 Kuurne Phone: +32 56.
Changes Barco provides this manual ’as is’ without warranty of any kind, either expressed or implied, including but not limited to the implied war- ranties or merchantability and fi tness for a particular purpose.
.
Tabl e of c onten ts T ABLE OF C ONTENTS 1 . X e n o n b u l b l a m p ..... ........ ........ ........ ........ .......... ........ ........ ........ ........ ........ ........ .... 3 1 . 1 I n t r o d u c t i o n ................. ..................
Tabl e of co nten ts 2 R59770175 XENON BULB LA MP REPLACEMENT 24/09/2008.
1. Xenon b ulb lamp 1. XENON BULB LAMP Safe ty Read all warnings and cautions at tentively . This to prevent per sonal injury while installing an xenon bulb lamp in the lam p house of the DP-1200/DP-1500/DP-2000 digital cinema projector .
1. Xenon b ulb lamp 1.1 Introduction Lamp & lamp house The xenon bulb lamp is delivered separately and ha s to be installed on site by a quali fi ed service technician. B A Image 1-1 A Lam p house. B X enon bulb lamp. Protective package The xenon bulb lamp is packed in a protec tive container or wrapped in a pr otective cloth.
1. Xenon b ulb lamp 1.2 Supported xenon bulb lamps Supported xenon bulb lamps (without lamp house) Lamp Ty p e Order i nfo Osram xenon bulb lamp of 4 kW 4kW DHP R9855937 Osram xenon bulb lamp of 3 kW .
1. Xenon b ulb lamp 6 R59770175 XENON BULB LA MP REPLACEMENT 24/09/2008.
2. Xenon b ulb lamp rep lacement pr ocess 2. XENON BULB LAMP REPLACEMENT PROCESS About this chapter This chapter descri bes how to replace the xenon bulb lamp in the lamp house.
2. Xenon bulb l amp replacement pr ocess 2.1 Remov al of the lamp house W ARNING : This proc edure may onl y be perfor med by quali fi ed technical service perso nnel. C AUTION : Lamp casing is very hot after operation. T o avoid burns, let the projector cool dow n for at least 15 minutes before proceeding to the lamp unit replacement.
2. Xenon b ulb lamp rep lacement pr ocess While starting up the projector , the electronics detect if a lamp is installed. If no lamp is installed, it is not possible to start up the projector .
2. Xenon bulb l amp replacement pr ocess 2.2 Re moval of the x e non bulb lamp W ARNING : DO NOT PER MIT UNAUTHORIZE D PERSONNEL TO PERFOR M OR A TTEMPT ANY PHASE O F XENON BULB LAMP HANDLING OR SERVICE. W ARNING : This proc edure may onl y be perfor med by quali fi ed technical service perso nnel.
2. Xenon b ulb lamp rep lacement pr ocess 3. Release the xenon bulb lam p fr om its socket by removing the hexagon socket head cap screw and plane washer as illustrated.
2. Xenon bulb l amp replacement pr ocess L N2 S W1 W2 N1 N1 N2 Image 2-6 7. Remove the cathode lamp adaptor (A) from the xenon bulb lamp (L) as illust rated. Us ea4m mA l l e nw r e n c ht or e l e a s et h e fi xation screw (S) of the adaptor . S L A Image 2-7 C AUTION : Expi red xenon bu lb lamps.
2. Xenon b ulb lamp rep lacement pr ocess 2.3 Installat ion of the xenon bulb lamp W ARNING : DO NOT PER MIT UNAUTHORIZE D PERSONNEL TO PERFOR M OR A TTEMPT ANY PHASE O F XENON BULB LAMP HANDLING OR SERVICE. W ARNING : This proc edure may onl y be perfor med by quali fi ed technical service perso nnel.
2. Xenon bulb l amp replacement pr ocess Image 2-8 3. Install the lamp cathode adapto r (A) upon the xenon bulb lamp (L) as illustrated. Use torq ue 2,5 Nm to fasten the fi xation screw ( S )o ft h ea d a p t e r . U s ef o rt h a tat o r q u ew r e n c hw i t ha5m m A l l e ns o c k e t .
2. Xenon b ulb lamp rep lacement pr ocess L N2 S W1 W2 N1 N1 N2 9 Nm Image 2-10 5. Remove the protective container or unwrap the prot ective cloth f rom the xenon bulb lamp. Warning: Ensure that you wear protective clothing, a f ull face shield and protect ive gloves.
2. Xenon bulb l amp replacement pr ocess Image 2-12 8. Reinstall the UV blocker ass embly as illustrated. Mak e sure that t he xenon bulb lamp is properly support ed by the lamp supporting mechanism in the centre of the UV blocker .
2. Xenon b ulb lamp rep lacement pr ocess 2,5 Nm A Image 2-15 1 1. Reinstall the side cover of the lamp house as illustrated. Note: Please ensure that the thumb screws turning wire s are fl ash with the cover or interf erence will occur while i nserting the lamp house into the projector .
2. Xenon bulb l amp replacement pr ocess 2.4 Installation of the lamp house W ARNING : This proc edure may onl y be perfor med by quali fi ed technical service perso nnel. C AUTION : Due to its hi gh internal pressure, the lamp may explode in either hot or cold states i f improperly hand led.
2. Xenon b ulb lamp rep lacement pr ocess While starting up the projector , the electronics detect if a lamp is installed. If no lamp is installed, it is not possible to start up the projector .
2. Xenon bulb l amp replacement pr ocess 2.5 Resetti ng the lamp parameters C AUTION : The “LAMP INFO” parameters which are stored on a chip MUST be updated after each installati on of an x enon b ulb lamp ins ide the lam p hous e. Neg l ecti ng this u pdate wi l l re sult in poo r perfo r m ance and sh ort lif e time o f the xenon bulb lamp.
2. Xenon b ulb lamp rep lacement pr ocess 2.6 Realignment of the lamp in it s re fl ector Each xenon bulb lamp installation req uires a realignment of the l amp in its re fl ec tor for op timal per formance of the xenon b u lb lamp in the D P-1200/DP-1500/ DP-2000 projector .
2. Xenon bulb l amp replacement pr ocess X LY Z Y LX Image 2-21 7. Fasten the X-axis lock thumb screw (ref LX image 2-21) and Y-axis lock thumb screw ( r ef L Y image 2- 21) . 8. Switch off the projector . 9. Reinstall the cover of the lamp compartment.
Index INDEX I Install 13, 18 Lamp house 18 Xenon lamp 13 Introduction 4 L Lamp 20–21 Realignment 21 Reset 20 Lamp house 8, 18 Install 18 Remove 8 R Realignment 21 Lamp 21 Remove 8, 10 Lamp house 8 X.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Barco DP-1200/DP-1500/DP-2000 R59770175/01 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Barco DP-1200/DP-1500/DP-2000 R59770175/01 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Barco DP-1200/DP-1500/DP-2000 R59770175/01 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Barco DP-1200/DP-1500/DP-2000 R59770175/01 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Barco DP-1200/DP-1500/DP-2000 R59770175/01, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Barco DP-1200/DP-1500/DP-2000 R59770175/01.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Barco DP-1200/DP-1500/DP-2000 R59770175/01. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Barco DP-1200/DP-1500/DP-2000 R59770175/01 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
