Manuale d’uso / di manutenzione del prodotto HG80 del fabbricante Stanley Black & Decker
Vai alla pagina of 18
© 2014 Stanley Black & Decker , Inc. New Britain, CT 06053 U.S.A. 28075 8/2014 V er . 8 USER MANUAL Safety , Operation and Maintenance HG80 HYDRAULIC GRINDER.
.
HG80 User Manual ◄ 3 SERVICING: This manual contains safety , operation, and routine maintenance instructions. Stanley Hydraulic T ools recommends that servicing of hydraulic tools, other than routine maintenance, must be performed by an authorized and certied dealer .
4 ► HG80 User Manual Always observe safety symbols. They are included for your safety and for the protection of the tool. LOCAL SAFETY REGULA TIONS Enter any local safety regulations here. Keep these instructions in an area accessible to the operator and mainte- nance personnel.
HG80 User Manual ◄ 5 T ool operators and maintenance personnel must always comply with the safety precautions given in this manual and on the stickers and tags attached to the tool and hose. These safety precautions are given for your safety . Re- view them carefully before operating the tool and before performing general maintenance or repairs.
6 ► HG80 User Manual GRINDING WHEEL SAFETY • Ensure that the grinding wheel is correctly mounted and tightened before use. • Operate the grinder at “no load” for 30 seconds in a safe position and ensure there is no vibration or other defects detected.
HG80 User Manual ◄ 7 25413 HG80 Name T ag 25610 Railroad Help Desk Sticker 03787 GPM Sticker 7–10 2000 PSI 25414 HG801 10B CAUTION DECAL 25556 HG80120B CAUTION DECAL 05153 Stanley Sticker SAFETY T AG P/N 15875 (Shown smaller then actual size) DANGER DANGER READ OPERA TION MANUAL AND SAFETY INSTRUCTIONS FOR THIS TOOL BEFORE USING IT .
8 ► HG80 User Manual The rated working pressure of the hydraulic hose must be equal to or higher than the relief valve setting on the hy- draulic system. There are three types of hydraulic hose that meet this requirement and are authorized for use with Stanley Hydraulic T ools.
HG80 User Manual ◄ 9 Oil Flow Hose Lengths Inside Diameter USE ( Press/Return) Min. Working Pressure GPM LPM FEET METERS INCH MM PSI BAR Certied Non-Conductive Hose - Fiber Braid - for Utility Bu.
10 ► HG80 User Manual Flow Range Nominal Operating Pressure (at the power supply outlet) System relief valve setting (at the power supply outlet) Maximum back pressure (at tool end of the return hose) Measured at a max. uid viscosity of: (at min.
HG80 User Manual ◄ 1 1 PRE-OPERA TION PROCEDURES PREP ARA TION FOR INITIAL USE Each unit as shipped has no special unpacking or as- sembly requirements prior to usage. Inspection to as- sure the unit was not damaged in shipping and does not contain packing debris is all that is required.
12 ► HG80 User Manual • Make sure all couplers are wiped clean before con- nection. • The hydraulic circuit control valve must be in the OFF position when coupling or uncoupling hydrau- lic tools. Failure to do so may result in damage to the quick couplers and cause overheating of the hy- draulic system.
HG80 User Manual ◄ 13 Problem Cause Solution Grinder does not run. Hydraulic power source not functioning. Check power source for proper ow and pressure (7–10 gpm/26–38 lpm @ 1500–2000 psi/105–140 bar . Couplers or hoses blocked. Locate and remove restriction.
14 ► HG80 User Manual Wheel Capacity ............................................................................................. 8 in. dia. × 1 in. thk × 5/8 arbor (type 1) Pressure Range .........................................................
HG80 User Manual ◄ 15 17 18 19 20 21 20 23 24 25 26 31 30 23 29 12 10 27 28 22 11 11 1 2 3 4 6 7 8 13 2 14 15 6 16 2 12 9 9 39 40 41 43 38 37 36 35 34 33 32 42 44 45 46 47 49 48 52 53 54 62 63 64 51.
16 ► HG80 User Manual ITEM P ART NO. QTY DESCRIPTION 1 25610 1 RAILROAD HELP DESK STICKER 2 06316 4 BUSHING 3 00178 1 O-RING, 2-1/8 × 2-1/4 × 1/16 -034 70D 4 06305 1 IDLER SHAFT (HG801 10, HG80120.
HG80 User Manual ◄ 17 ITEM P ART NO. QTY DESCRIPTION 63 01298 3 LOCKW ASHER 64 25907 3 MODIFIED CAPSCREW 65 25414 1 CAUTION STICKER (HG801 10B) 25556 1 CAUTION STICKER (HG80120B) 66 01459 2 LOCKW AS.
Stanley Hydraulic T ools 3810 SE Naef Road Milwaukie, Oregon 97267-5698 USA (503) 659-5660 / Fax (503) 652-1780 www .stanleyhydraulics.com.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Stanley Black & Decker HG80 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Stanley Black & Decker HG80 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Stanley Black & Decker HG80 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Stanley Black & Decker HG80 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Stanley Black & Decker HG80, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Stanley Black & Decker HG80.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Stanley Black & Decker HG80. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Stanley Black & Decker HG80 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
