Manuale d’uso / di manutenzione del prodotto HD01 del fabbricante Stanley Black & Decker
Vai alla pagina of 20
© 2014 Stanley Black & Decker , Inc. New Britain, CT 06053 U.S.A. 72659 2/2015 V er . 6 USER MANUAL Safety , Operation and Maintenance HD01 Hydraulic Hammer Drill.
2 ► HD01 User Manual DECLARATION OF CONF ORM ITY ÜBEREINSTIMM UNGS - ERKLARUNG DECLARATION DE CONF ORMITE CEE DECLARACION DE CONFO RMIDAD DICHIARAZIONE DI CONFO RMITA Hydraulic Tools _______ ______.
HD01 User Manual ◄ 3 SERVICING: This manual contains safety , operation, and routine maintenance instructions. Stanley Hydraulic T ools recommends that servicing of hydraulic tools, other than routine maintenance, must be performed by an authorized and certied dealer .
4 ► HD01 User Manual Always observe safety symbols. They are included for your safety and for the protection of the tool. LOCAL SAFETY REGULA TIONS Enter any local safety regulations here. Keep these instructions in an area accessible to the operator and mainte- nance personnel.
HD01 User Manual ◄ 5 T ool operators and maintenance personnel must always comply with the safety precautions given in this manual and on the stickers and tags attached to the tool and hose. These safety precautions are given for your safety . Re- view them carefully before operating the tool and before performing general maintenance or repairs.
6 ► HD01 User Manual SAFETY T AG P/N 15875 (Shown smaller then actual size) DANGER DANGER READ OPERA TION MANUAL AND SAFETY INSTRUCTIONS FOR THIS TOOL BEFORE USING IT . USE ONL Y P ARTS AND REP AIR PROCEDURES APPROVED BY ST ANLEY AND DESCRIBED IN THE OPERA TION MANUAL.
HD01 User Manual ◄ 7 The rated working pressure of the hydraulic hose must be equal to or higher than the relief valve setting on the hy- draulic system. There are three types of hydraulic hose that meet this requirement and are authorized for use with Stanley Hydraulic T ools.
8 ► HD01 User Manual Oil Flow Hose Lengths Inside Diameter USE ( Press/Return) Min. Working Pressure GPM LPM FEET METERS INCH MM PSI BAR Certied Non-Conductive Hose - Fiber Braid - for Utility Bu.
HD01 User Manual ◄ 9 Flow Range Nominal Operating Pressure (at the power supply outlet) System relief valve setting (at the power supply outlet) Maximum back pressure (at tool end of the return hose) Measured at a max. uid viscosity of: (at min. operating temperature) T emperature: Sufcient heat rejection capacity to limit max.
10 ► HD01 User Manual PRE-OPERA TION PROCEDURES CHECK POWER SOURCE 1. Using a calibrated owmeter and pressure gauge, check that the hydraulic power source develops a ow of 4–9 gpm/15–34 lpm at 950–2000 psi/65–140 bar .
HD01 User Manual ◄ 1 1 MODE SELECTOR (FIG 2) Drill only mode: T o use drill-only mode, press mode selector button (B) g-2 and turn the mode selec - tor (A) so the yellow arrow points to the corresponding symbol. Use drill-only mode for screwdriving and for drilling into metal, wood and plastics.
12 ► HD01 User Manual SIDE HANDLE The side handle assembly , including the depth gauge, ts over the front housing of the hammer drill to assist the operator in maneuvering the tool. T o adjust the side handle to a comfortable position, twist the hand grip in a counterclockwise direction and reposi- tion the handle assembly .
HD01 User Manual ◄ 13 T ighten further by applying the chuck key successively to all three guide holes of the chuck. The chuck key must not be attached to the tool with a chain, cord, or similar means.
14 ► HD01 User Manual This tool is furnished with an on-off valve spool commonly referred to as a “dual spool” which permits adjustment so the tool may be operated on either an open-center hydraulic system or a closed-center hydraulic system. The dual spool is normally set to the open-center (OC) position at time of manufac- ture.
HD01 User Manual ◄ 15 PROBLEM CAUSE SOLUTION Drill will not start Power not being supplied. Check to make certain that both hoses are connected. T urn hydraulic circuit control valve ON. Defective quick-disconnect. Check each disconnect separately .
16 ► HD01 User Manual PROBLEM CAUSE SOLUTION Drill operates in only one direction. Forward or reverse. Reverse spool incorrectly installed. Do not separate modules. Reassemble. See Service section. Reverse spool faulty . Do not separate modules. Replace reverse spool.
HD01 User Manual ◄ 17 Rotation Speed at 6 gpm ................................................................................................................................ 800 rpm Blows per Minute at 6 gpm ........................................
18 ► HD01 User Manual 1 2 3 4 5 6 8 9 10 11 12 13 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 43 45 47 48 50 51 52 53 56 57 58 60 62 64 65 6 19 14 46 16 16 42 61.
HD01 User Manual ◄ 19 ITEM P/N QTY DESCRIPTION 1 00106 1 * O-RING 3/8 X 1/2 X 1/16 -012 2 001 12 1 * QUAD RING 1/4 X 3/8 X 1/16 -010 3 00179 1 MOT OR SEAL W ASHER 4 00289 2 DOWEL PIN 3/16 X 3/4 LG. 5 00621 1 * O-RING 1-1/4 X 1-3/8 X 1/16 -026 6 00779 7 HSHCS 8-32 X 1.
Stanley Hydraulic T ools 3810 SE Naef Road Milwaukie, Oregon 97267-5698 USA (503) 659-5660 / Fax (503) 652-1780 www .stanleyhydraulics.com.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Stanley Black & Decker HD01 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Stanley Black & Decker HD01 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Stanley Black & Decker HD01 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Stanley Black & Decker HD01 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Stanley Black & Decker HD01, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Stanley Black & Decker HD01.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Stanley Black & Decker HD01. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Stanley Black & Decker HD01 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
