Manuale d’uso / di manutenzione del prodotto EP30 del fabbricante Stanley Black & Decker
Vai alla pagina of 21
EP30 ELECTRONIC PIN BRAZING S afety , O pera tiOn and M aintenance USer'S ManUaL © 201 1 Stanley Black & Decker , Inc. New Britain, CT 06053 U.
.
3 T ABLE OF CONTENTS SERVICING: This manual contains safety , operation, and routine maintenance instructions. Stanley Hydraulic T ools recommends that servicing of hydraulic tools, other than routine maintenance, must be performed by an authorized and certied dealer .
4 DECLARA TION OF CONFORMITY DECLARATION OF CONF ORM ITY ÜBEREINSTIMM UNGS - ERKLARUNG DECLARATION DE CONF ORMITE CEE DECLARACION DE CONFO RMIDAD DICHIARAZIONE DI CONFO RMITA Hydraulic Tools _______ .
5 Safety symbols and signal words, as shown below , are used to emphasize all operator , maintenance and repair actions which, if not strictly followed, could result in a life-threatening situation, bodily injury or damage to equipment.
6 T ool operators and maintenance personnel must always comply with the safety precautions given in this manual and on the stickers and tags attached to the tool and hose. These safety precautions are given for your safety . Review them carefully before operating the tool and before performing general maintenance or repairs.
7 WARNING Make sure battery charging is only accomplished in a well ventilated room. DO NOT PLACE THE CONTROL BOX ON T OP OF THE BA TTERIES. REMOVE THE BA TTER Y BOX COVER. Battery charging produces explosive gases. A battery explosion can cause serious injuries.
8 OPERA TION PREP ARE THE RAIL SURF ACE Select the type and length of bonding cable to use for the bond and use it as a guide to determine where brazing points on the rail will be required.
9 OPERA TION Pin Holder Ring Holder SWITCH Dial a. The ring holder is a "push t" to the gun. T o remove it from the gun, simply pull it away from the gun. b. The pin holder is threaded onto a threaded shaft in the gun and locked in place with a nut.
10 OPERA TION NOTE: The EP30 does not have a power switch. 1 1. Position the terminal lug of the bonding cable against the cleaned surface of the rail. Position the gun against the cable lug so that the brazing pin is at the top edge of the cable lug hole.
11 • Check that the pin holder is not burnt or not holding the pin tightly . If not, remove the ring holder , clean all the parts and squeeze the ngers of the pin holder together . • Check the cables on the gun from time to time for damage. Replace as required.
12 TROUBLESHOOTING PROBLEM CAUSE SOLUTION Brazing pin does not ignite or does not ignite long enough. Batteries not charged or are defective. T est batteries for proper charge. Replace and/or charge as necessary . Blown fuse. Check fuses. Magnetic ground faulty .
13 SPECIFICA TIONS EP30 V oltage ............................................................................................................................................................................................... 36V dc Approximate Number of Brazings per Battery Charge .
14 PIN & RING HOLDERS 35826 Pin Holder for Pinbrazing, 8-9,5 mm brazing pins. 35827 Pin Holder for Pinbrazing, M8 Threaded pins. 35828 Pin Holder for Pinbrazing, M10 Threaded pins. 35829 Pin Holder for Pinbrazing, M12 Threaded pins. 35825 Extended pin and ring holder set for 8-9,5 mm brazing pins.
15 BONDING CABLE WITH LUGS (for Pin Brazing) Part No. Description Brazing Pin Reqd 35845 1 A WG / 50 mm², 185 mm long, copper 35837 35844 4 A WG / 25 mm², 145 mm long, copper 35835 39243 3/16 Bond, .
16 Fuses, Chargers, & Batteries Part No. Description 56557 Fuse, PCB EP30/60 56558 Fuse, Grinder Outlet EP30 56559 Fuse, Control Cable EP30 56560 Auto Fuse, 5A EP60 56561 Auto Fuse, 15A EP60 56562 Auto Fuse, 30A EP60 35866 Charger 36 VDC 7 AMP EP30/60 W/ Special DC plug.
17 CABLES Part No. Description 35809 Ground Cable_____________________________________ 35806 Carrying Harness__________________________________ 35820 Extension Cable for Grinding______________________.
18 GUNS Part No. Description BG10100 Pin Brazing Gun____________________________________ BG10101 Angle Head Gun____________________________________ ACCESSORIES Continued: Plugs Part No.
19 A A 01 02 03 04 05 06 07 09 13 12 08 18 17 14 14 19 24 15 16 16 15 10 11 11 23 23 20 30 29 27 28 28 22 21 24 25 25 25 26 26 25 26 25 31 26 25 25 26 29 30 25 31 30 30 29 29 32 32 33 Electronic box for EP30 XC 34.
20 EP30 P ARTS LIST Item Part No. Qty Description 01 66838 1 FRAME EP30 02 66846 1 LABEL EP30 03 66839 1 CIRCUIT BOARD 04 66018 1 RELA Y 05 66840 1 CIRCUIT BOARD MOUNTING PLA TE 06 66841 1 RESISTOR MO.
Stanley Hydraulic T ools 3810 SE Naef Road Milwaukie, Oregon 97267 503-659-5660 / Fax 503-652-1780 www .stanleyhydraulic.com.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Stanley Black & Decker EP30 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Stanley Black & Decker EP30 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Stanley Black & Decker EP30 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Stanley Black & Decker EP30 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Stanley Black & Decker EP30, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Stanley Black & Decker EP30.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Stanley Black & Decker EP30. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Stanley Black & Decker EP30 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
