Manuale d’uso / di manutenzione del prodotto DL07 del fabbricante Stanley Black & Decker
Vai alla pagina of 20
© 2014 Stanley Black & Decker , Inc. New Britain, CT 06053 U.S.A. 49234 2/2015 V er . 10 USER MANUAL Safety , Operation and Maintenance DL07 HYDRAULIC DRILL.
2 ► DL07 User Manual DECLARA TION OF CONFORMITY DECLARATION OF CONF ORM ITY ÜBEREINSTIMM UNGS - ERKLARUNG DECLARATION DE CONF ORMITE CEE DECLARACION DE CONFO RMIDAD DICHIARAZIONE DI CONFO RMITA Hyd.
DL07 User Manual ◄ 3 DECLARA TION OF CONFORMITY .......................................................................................................................... 2 SAFETY SYMBOLS .............................................................
4 ► DL07 User Manual Always observe safety symbols. They are included for your safety and for the protection of the tool. LOCAL SAFETY REGULA TIONS Enter any local safety regulations here. Keep these instructions in an area accessible to the operator and mainte- nance personnel.
DL07 User Manual ◄ 5 T ool operators and maintenance personnel must always comply with the safety precautions given in this manual and on the stickers and tags attached to the tool and hose. These safety precautions are given for your safety . Re- view them carefully before operating the tool and before performing general maintenance or repairs.
6 ► DL07 User Manual 28322 CE STICKER (CE) 1 1207 CIRCUIT TYPE D STICKER (CE) D 30 LPM @ 138 BA R EHTMA CA TEGORY 28788 MANUAL STICKER (CE) 58862 PRESSURE W ARNING STICKER 60807 DL07 MODEL STICKER Stanley Hydraulic T ools 3810 SE Naef Road Milwaukie, Oregon USA 26-45 LPM / 7-12 GPM 140 BAR / 2000 PSI Model No.
DL07 User Manual ◄ 7 The rated working pressure of the hydraulic hose must be equal to or higher than the relief valve setting on the hy- draulic system. There are three types of hydraulic hose that meet this requirement and are authorized for use with Stanley Hydraulic T ools.
8 ► DL07 User Manual Oil Flow Hose Lengths Inside Diameter USE ( Press/Return) Min. Working Pressure GPM LPM FEET METERS INCH MM PSI BAR Certied Non-Conductive Hose - Fiber Braid - for Utility Bu.
DL07 User Manual ◄ 9 Flow Range Nominal Operating Pressure (at the power supply outlet) System relief valve setting (at the power supply outlet) Maximum back pressure (at tool end of the return hose) Measured at a max. uid viscosity of: (at min. operating temperature) T emperature: Sufcient heat rejection capacity to limit max.
10 ► DL07 User Manual PREOPERA TION PROCEDURES CHECK POWER SOURCE 1. Using a calibrated ow meter and pressure gauge, check that the hydraulic power source develops a ow of 4-12 gpm/15-45 lpm at 1000-2000 psi/70- 140 bar . 2. Make certain that the hydraulic power source is equipped with a relief valve set to open at 2100 psi/145 bar minimum.
DL07 User Manual ◄ 1 1 Ductile material such as metal or wood is drilled ef - ciently when a steady down force is applied to the drill center to cause the bit to slice chips of material from the hole bottom. When drilling in metal, use a cutting lubri- cant to prolong bit life and reduce the amount of force required to drill effectively .
12 ► DL07 User Manual • Make sure all couplers are wiped clean before con- nection. • The hydraulic circuit control valve must be in the “OFF” position when coupling or uncoupling hydrau- lic tools. Failure to do so may result in damage to the quick couplers and cause overheating of the hy- draulic system.
DL07 User Manual ◄ 13 If symptoms of poor performance develop, the following chart can be used as a guide to correct the problem. When diagnosing faults in operation of the wrench, always check that the hydraulic power source is supplying the correct hydraulic ow and pressure to the tool as listed in the following table.
14 ► DL07 User Manual Drive Size ............................................................................................................. 1/2 inch / 1.3 cm 3-Jaw Adjustable 5/8 -16 THD Chuck Drill T orque .......................................
DL07 User Manual ◄ 15 DESCRIPTION P ART NUMBER WOOD AUGER BITS, 5/8 INCH HEX 9/16 inch dia × 18 inch Carbide T ipped Auger Bit (22 inch OAL) ...................................................................... 27845 13/16 inch dia × 18 inch Carbide T ipped Auger Bit (22 inch OAL) .
16 ► DL07 User Manual 55 53 58 33 35 30 57 27 5 29 26 14 23 36 24 25 28 4 71 69 32 31 38 20 80 34 22 37 74 54 3 41 56 75 52 6 81 66 79 40 60 1 18 59 68 72 2 17 10 64 73 63 65 67 62 49 12 48 11 77 16.
DL07 User Manual ◄ 17 ITEM P/N QTY DESCRIPTION 1 00026 1 O-RING 2 00175 2 O-RING 3 00231 6 LOCKWASHER 4 00354 1 O-RING 5 00563 1 ROLL PIN 6 00713 2 DOWEL PIN 7 00717 1 O-RING 8 62229 2 CAPSCREW 9 01.
18 ► DL07 User Manual For underwater hydraulic tools the applications are broken down into four quadrants depending on type of tool and method of operation. The types of tools are percussive and rotational, each with different characteristics allowing for dif- ferent depth operation.
DL07 User Manual ◄ 19 NOTES.
Stanley Hydraulic T ools 3810 SE Naef Road Milwaukie, Oregon 97267-5698 USA (503) 659-5660 / Fax (503) 652-1780 www .stanleyhydraulics.com.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Stanley Black & Decker DL07 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Stanley Black & Decker DL07 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Stanley Black & Decker DL07 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Stanley Black & Decker DL07 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Stanley Black & Decker DL07, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Stanley Black & Decker DL07.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Stanley Black & Decker DL07. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Stanley Black & Decker DL07 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
