Manuale d’uso / di manutenzione del prodotto CP-2012 del fabbricante Spracht
Vai alla pagina of 19
V oice Center ™ Conference Phone Model CP-2012 User's Manual.
T able of Contents - V oice Center User’s Manual Introduction and Quick Start Guide Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . .
Introduction Thank you for choosing the V oice Center Conference Phone, a high per formance audio conferencing system. Its features include: • Full duplex communication – the V oice Center’ s digital speech processing enables simultaneous two-way communication.
3 Quick Start Guide 3. Analog or Digital T elephone System? Caution: if the V oice Center is connected to a digital telephone system using the Analog T elephone System Inter face, it will not operate correctly , and may cause damage to the A T -103 Analog Interface and cause it to over heat.
Analog T elephone System Setup with Analog T elephone System If you are connecting the V oice Center Conference Phone to an analog telephone system, follow the instructions below .
W all Mounting of Analog Interface (Optional) • Install the two mounting screws supplied with the Analog Inter face in the wall. Leave approximately 3/16 in. (0.5 cm) between screw head and wall. • Place the Analog Inter face over the mounting screws and slide it down to fix it in position.
Keypad Functions with Analog Phone System ON/OFF Pressing the ON/OFF key turns the Conference Phone on to obtain a dial tone, or turns it off to terminate a call.
Conference Phone Operation with Analog Phone System Answering a call When the Conference Phone rings, press the ON/OFF key to answer the call. The green LED illuminates to indicate the Conference Phone is on.
Digital T elephone System Setup of Conference Phone with Digital Phone System Note: The DT -104 Digital T elephone System Inter face is required for use of the Voice Center Conference Phone with a digital phone system. Follow the steps below to set up the system.
4. Use Digital Inter face’s 4-position switch to adjust audio level by making a test call. • Lift digital telephone handset from its cradle, then press Conference Phone’ s “On/Off” key .
Keypad Functions with Digital Phone System ON/OFF Pressing the ON/OFF key turns the Conference Phone on to connect a call, or turns it off to terminate the Conference Phone conversation. When the Conference Phone is on, green LEDs illuminate by all active microphones.
Conference Phone Operation with Digital Phone System Answering a call 1. When the phone rings, pick up the digital telephone handset to accept the call.
General Setup T ips T ips for Obtaining Optimal Acoustic Performance • T o minimize echoes, place the Conference Phone at the center of the room, or at least away from walls (at least 20 inches/0.5 m from any wall). • It is impor tant to place the Conference Phone on the sur face where it will be used before applying power .
'ENERAL )NSTALLATION OF %XTERNAL -ICR OPHONES /PTIONAL 4HE 6 OICE #ENTER #ONFERENCE 0HONE HAS BUILTIN MICROPHONES FOR COMPLETE .
Specifications Conference Phone Controls and Interface Switches Microphone switch to turn on T one/pulse switch to select 2, 3 or all 4 built-in microphones telephone dialing mode LED indication light.
Spracht Limited W arranty Policy Spracht warrants it products against defects or malfunctions in material and workmanship under normal use and ser vice, with the exceptions stated below . This warranty lasts for one year from the original date of purchase.
16.
Federal Communications Commission Statement Note: The V oice Center Conference Phone equipment has been tested and found to comply with the limits for a Class B Digital Device, pursuant to Par t 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
SPRACHT T el: 650-318-8061 Fax: 650-318-8060 2672 Bayshore Parkway , Bldg 900 Mountain View , CA 94043 USA www .spracht.com © 2003 Spracht Spracht and V oice Center are trademarks of ODI.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Spracht CP-2012 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Spracht CP-2012 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Spracht CP-2012 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Spracht CP-2012 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Spracht CP-2012, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Spracht CP-2012.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Spracht CP-2012. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Spracht CP-2012 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
