Manuale d’uso / di manutenzione del prodotto M881111 del fabbricante Spalding
Vai alla pagina of 32
1 12/05 ID# M881111 © COPYRIGHT 2005 SPALDING Customer Service Center • N53 W24700 South Corporate Circle • Sussex, WI 53089 • U.S.A. • 2 People • Carpenter’s Level • 15’ Tape Measure.
2 ID# M881111 12/05 BEFORE YOU ST ART! T o ensure optimal playability of backboard system, a close tolerance fit between the elevator components and hardware is required. T est-fit large bolts into large holes of elevator tubes, backboard brackets, and triangle plates.
12/05 ID# M881111 3 7-3/8" High 4" Wide PMS 021 for W arning Owner must ensure that all players know and follow these rules for safe operation of the system. W ARNING • DO NOT HANG on the rim or any part of the system including backboard, support braces or net.
4 ID# M881111 12/05 EXACT AHEIGHT : ADJUSTMENT INGROUND 201251 Eng: DanT om 1st Used: 2/99 Size = 4" x 3" Corner Radius = 3/8" Die Cut Label 3.
12/05 ID# M881111 5 For more information on assembly, placement, proper use, and maintenance, visit The American Basketball Council website at http://www.smarthoops.com. IMPORT ANT! Remove all content s from boxes. Be sure to check inside pole sections; hardware and additional p arts are p acked inside.
6 ID# M881111 12/05 Item Qty. Part No. Description 1 1 908123 Top Pole Section 2 1 90812501 Middle Pole Section 3 1 908124 Bottom Pole Section 4 2 202800 Ground Sleeve 5 1 202801 Ground Sleeve Cap 6 1.
12/05 ID# M881111 7 #8 (9)* #10 (4) HARDW ARE IDENTIFIER (BOL TS & SCREWS) HARDW ARE IDENTIFIER (NUTS & W ASHERS) HARDW ARE IDENTIFIER (MET AL SP ACERS) #13 (2) #7 (2) #1 1 (4) #15 (1)* #20 (2) #24 (6) #21 (1) #27 (6) #42 (1) #46 (1) #45 (1) #47 (4) #9 (4) * You may have extra parts with this model.
8 ID# M881111 12/05 #44 (1) #41 (1) #43 (1) HARDW ARE IDENTIFIER (PLASTIC SP ACERS & CLIPS) HARDW ARE IDENTIFIER (OTHER) #23 (4) #22 (4) #12 (2) #39 (2).
12/05 ID# M881111 9 SECTION A: ASSEMBLE THE POLE This is what your system will look like when you’ve finished this section: T OOLS REQUIRED FOR THIS SECTION Shovel and Post Hole Digger Carpenter&apo.
10 ID# M881111 12/05 XG08.EPS 205334 18" (42.7 cm) 6" (15.2 cm) 24" (61 cm) PLAYING SURFACE GROUND SURFACE 2. Ensure ground is level with playing surface, then dig pole hole.
12/05 ID# M881111 11 3. Snap two halves of ground sleeve (4) together . Insert and secure bottom pole section (3) into ground sleeve (4) by tightening ground sleeve cap (5). 3 5 4 4 4 Flared end goes inside ground sleeve. NOTE: 4. Fill hole approximately 1/3 full with mixed concrete.
12 ID# M881111 12/05 1 " (2.54 cm) 1" (2.54 cm) 1" (2.54 cm) SIDE VIEW FIG . A FLANGE Insert ground sleeve assembly and center in hole ( FIG . A ). 5. IMPORT ANT! CONTINUE ON T O NEXT STEP . DO NOT W AIT FOR CONCRETE TO CURE. PLAYING SURFACE Leave 1" below flange exposed for drainage hill.
12/05 ID# M881111 13 4 3 Fill hole completely with concrete. 6. 1" (2.54 cm) 1" (2.54 cm) 1" (2.54 cm) 5 GSLV09.EPS 211121 1" (2.54 cm) 7. T amp down concrete to release air pockets and build drainage hill. Level pole section in all directions several times while concrete is curing.
14 ID# M881111 12/05 Af ter concrete has cured, remove bottom pole section from ground sleeve (4). Place anti- skid tape (36) around the bottom area of bottom pole (see note A). 4 8. 5 36 Place top edge of anti- skid tape on mark made in step 7, NOTE A.
12/05 ID# M881111 15 9. S tack and bounce bottom (3) and middle (2) pole sections together . Bounce pole sections together until middle section no longer moves toward taped reference mark on bottom pole. 2 3 W ood Scrap (NOT SUPPLIED) Identification Sticker KEEP GROUND SLEEVE CAP ON BOTT OM POLE.
16 ID# M881111 12/05 10. S tack upper pole section (1) to bottom and middle pole assembly and continue bouncing until top pole (1) no longer moves toward taped reference mark on middle pole. 1 5 IMPORT ANT! POLE SECTIONS SHOULD HA VE A 3-1/2" (9 CM) MINIMUM OVERLAP .
12/05 ID# M881111 17 11 . Install pole mount bracket (6) and bracket reinforcement (40) with carriage bolt s (7) as shown. T ighten flange nuts (8) completely .
18 ID# M881111 12/05 12 6 12 13 13 11 9 10 10 12. 6 8 14 14 17 15 13. Attach sp acers (12, 13) to pole mount bracket (6) with bolts (9), washers (10), and nuts (1 1) as shown. Assemble lanyard (17) to locking pin (16) as shown. Attach covers (14) onto pole mount bracket (6) with carriage bolt (15) and nut (8) as shown.
12/05 ID# M881111 19 20 19 38 37 21 18 14. 20 15. 16 Insert handle assembly through pole mount assembly as shown. Lock pole assembly in place at the 10’ (3.05 m) mark with pin (16). Apply logo and height indicator labels (19) to adjustment rod (18) as shown.
20 ID# M881111 12/05 SECTION B: ASSEMBLE THE ELEV A T OR TUBES T O BACKBOARD This is what your system will look like when you’ve finished this section. 9/16” 3/4” 1/2” (2) 1/2”, (2) 9/16”, and 2 3/4” Wrenches (2) Socket Wrenches and Socket s T OOLS REQUIRED FOR THIS SECTION AND/OR 1 .
12/05 ID# M881111 21 A ttach backboard support bracket s (25) to the backboard frame using bolts (31) and nut s (10) as shown. 1 . 25 11 25 31 11 31 IMPORT ANT! IMPORT ANT! DO NOT TIGHTEN HARDW ARE COMPLETEL Y .
22 ID# M881111 12/05 2. 27 29 22 22 25 24 47 28 Attach lower elevator tubes (28) and springs (29) to backboard support bracket s (25) using spacers (22), bolt (27), and nut (24) as shown. Insert T -bolt (42) into Slam Jam bracket (41) then, attach that assembly to board using bolt s (47) and nuts (8).
12/05 ID# M881111 23 3. Attach upper elevator tubes (30) to backboard support brackets (25) using sp acers (22), bolt (27), and nut (24) as shown. 22 24 28 28 30 27 25 30 29 22 IMPORT ANT!.
24 ID# M881111 12/05 SECTION C: A TT ACH THE BACKBOARD & ELEV A T OR ASSEMBL Y T O POLE SYSTEM This is what your system will look like when you’ve finished this section: 3/4” CONCRETE T OOLS R.
12/05 ID# M881111 25 1. 1 24 30 30 23 23 23 23 24 28 28 2. Support pole on sawhorse. Attach backboard assembly to top pole section (1). Install handle assembly to long elevator tubes (28) using bolt (27), spacers (39), and nut (24) as shown. NOTE: Before going on to next step, adjust system assembly to the 10’ setting.
26 ID# M881111 12/05 3. 43 46 45 42 Inst all Slam Jam Rim to Backboard 44 42 45 46 B C D E A • Fit rim (32) securely into bracket (41) as shown (Allow "T"-bolt (42) to slip through center hole in rim (32). B • Install reinforcement bracket (43) onto “T” bolt (42) as shown.
12/05 ID# M881111 27 5. 24 27 30 30 29 Insert bolt (27) through left side short elevator tube (30), then stretch spring or springs (29) onto bolt (27). Insert bolt (27) through right side short elevator tube (30) and secure with nut (24). USE EYE PROTECTION WHEN INST ALLING SPRINGS.
28 ID# M881111 12/05 Place rebar with spacers into bottom pole section (3) as shown. 7. Assemble rebar centering spacers (49) near top and bottom of rebar (48) as shown. 6. 48 Tape (Not Included) 49 48 49 49 48 3 Seal hole at the bottom of the bottom pole with heavy-duty tape (not included) to ret ain rebar and concrete inside.
12/05 ID# M881111 29 Fill pole with concrete approximately 1” (2.54 cm) below bottom elevator hole as shown. IMPORT ANT!: W AIT A MINIMUM OF 24 HOURS BEFORE GOING ON T O NEXT STEP .
30 ID# M881111 12/05 SECTION D: UPRIGHT , SECURE AND USE POLE SYSTEM This is what your system will look like when you’ve finished this section. Wedge Hammer T OOLS REQUIRED FOR THIS SECTION.
12/05 ID# M881111 31 5 2. 1. Use wedge to tap cap of ground sleeve until tight. 4 10 ft (3.05 m) 26 Af ter concrete has cured, remove t ape, install pole cap (26), fit pole assembly into sleeve (4). DO NOT USE THE BACKBOARD OR RIM TO MOVE POLE ASSEMBL Y INT O POSITION.
32 ID# M881111 12/05 4. 16 B. A. C. 3. A. While holding handle, remove pin (16). B. Move elevator up or down to desired height. C. Replace pin (16) full length to lock system at desired height. Apply height adjustment label (35) to front of pole as shown.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Spalding M881111 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Spalding M881111 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Spalding M881111 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Spalding M881111 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Spalding M881111, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Spalding M881111.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Spalding M881111. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Spalding M881111 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
