Manuale d’uso / di manutenzione del prodotto M880961 del fabbricante Spalding
Vai alla pagina of 16
1 02/06 ID# M880961 In-Ground Basketball System Owners Manual Customer Service Center • N53 W24700 South Corporate Circle • Sussex, WI 53089 • U.S.A. READ AND UNDERSTAND OPERATOR'S MANUAL BEFORE USING THIS UNIT. FAILURE TO FOLLOW OPERATING INSTRUCTIONS COULD RESULT IN INJURY OR DAMAGE TO PROPERTY.
2 ID# M880961 02/06 IMPORT ANT! WRITE MODEL NUMBER FROM BOX ONTO P AGE 1 OF THIS OWNERS MANUAL Owner must ensure that all players know and follow these rules for safe operation of the system. W ARNING • DO NOT HANG on the rim or any part of the system including backboard, support braces or net.
3 02/06 ID# M880961 24" (61 cm) 36" (91.4 cm) Ensure ground is level with playing surface, then dig pole hole. GROUND SURFACE PLAYING SURFACE 1. Install threaded ends of J-bolts (1) through holes in mounting plate (3) and secure as shown. 2.
4 ID# M880961 02/06 Fill hole with concrete. Tamp down concrete to release air pockets and build drainage hill. Insert J-bolts (1) from mounting plate (3) into cement as shown. Move assembly around to release any air pockets in cement, then rest mounting plate on cement drainage hill.
5 02/06 ID# M880961 PLA YING SURF A CE Upright pole (5). Assemble lower pole flange onto protruding J-bolts (1) as shown. The flange will then rest on the nuts (2). Secure pole (5) flange to mounting plate (3) as shown. Tighten completely. 6. 7. 5 3 2 6 6 6 2 6 2 6 1 1 5 THREE CAP ABLE ADUL TS REQUIRED FOR THIS PROCEDURE.
6 ID# M880961 02/06 8. 7 14 28 13 27 12 33 27 28 27 28 14 28 13 7 THREE CAP ABLE ADUL TS REQUIRED FOR THIS PROCEDURE. F AILURE TO FOLLOW THIS W ARNING COULD RESUL T IN SERIOUS INJUR Y AND/OR PROPERTY DAMAGE. W ARNING! Beginning with upper support arm (8) secure support arms to pole.
7 02/06 ID# M880961 9. Secure backboard to support arms (8 and 9) as s hown. IMPORT ANT! Do Not Over Tighten. 8 13 27 10 28 14 14 13 28 13 27 28 10 13 14 13 28 10 13 27 28 28 IMPORT ANT! Bushing types are identified with a letter .
8 ID# M880961 02/06 PLA YING SURF AC E 10. Secure jack brackets (21) to to mounting bracket as shown. 21 21 11 1 1. REAR VIEW 20 13 13 14 Position U-joint of crank jack (20) as shown. Where tubes on crank jack join, hold steady to keep both tubes from rot ating.
9 02/06 ID# M880961 12. A. B. A . Insert spacer (4) through spacer of screw jack as shown. B. Install crank jack (20) U-joint to lower support arm (9) as shown. PLA YING SURF AC E TWO CAP ABLE ADUL TS REQUIRED FOR THIS PROCEDURE. F AILURE TO FOLLOW THIS W ARNING COULD RESUL T IN SERIOUS INJUR Y AND/OR PROPERTY DAMAGE.
10 ID# M880961 02/06 PLA YING SURF ACE 34 13 21 15 15 13 14 20 Some adjustment will be necessary to align the lower crank jack and bushings to jack bracket s (21). NOTE: REAR VIEW TWO CAP ABLE ADUL TS REQUIRED FOR THIS PROCEDURE. F AILURE TO FOLLOW THIS W ARNING COULD RESUL T IN SERIOUS INJUR Y AND/OR PROPERTY DAMAGE.
11 02/06 ID# M880961 PLA YING SURF AC E A pply height indicator labels (18 and 19) to height indicators (16). Attach height indicators (16) to lower arm in areas as shown by turning screws (17) into place with a phillips screwdriver .
12 ID# M880961 02/06 29 22 25 Attach rim assembly (29). For rim assembly, see instructions included with rim. Rim Assembly 16. IMPORT ANT! Carefully cut and peel protective film away from board prior to att aching rim. Remove rim cover prior to inst alling rim assembly to board.
13 02/06 ID# M880961 Apply height adjustment label (31) to front of pole as shown. 18. 10FT_HER.EPS 206239 REGULA TION RIM HEIGHT IS 10 FEET (3.05 m). 31 17. C heck leveling at this time. Pole (5) should be level in all directions. After system is leveled, completely tighten nuts (2) above pole flange.
14 ID# M880961 02/06 Rotate crank handle to raise or lower backboard. M83014.EPS 211560 20. Secure pole pad (32) as shown. 19. 32 MHE19.EPS 206239 M83013.EPS 211560 Height Adjustment If height adjustment is difficult to operate, you may have over tightened the areas indicated.
15 02/06 ID# M880961 P ARTS LIST HARDW ARE IDENTIFIER (BOL TS) Item Qty. Part No. Description 1 4 200573 J-Bolt, 1/2-13 x 24” Long 2 12 265575 Nut, Hex, 5/8-11 3 1 900661 Anchor Plate 4 1 220579 Spacer, 0.53 I.D. x 0.75 O.D. x 5” Long 5 1 908310 Pole 6 8 200704 Washer, 5/8” x 1.
16 ID# M880961 02/06 Item #25 (6) Item #26 (4)* Item #27 (8) Item #7 (2) Item #15 (2) Item #28 (20) spacer 1/2 x 5 Long Item #4 (1) * You May Have Extra Parts With This Model.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Spalding M880961 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Spalding M880961 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Spalding M880961 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Spalding M880961 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Spalding M880961, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Spalding M880961.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Spalding M880961. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Spalding M880961 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
