Manuale d’uso / di manutenzione del prodotto M8809511 del fabbricante Spalding
Vai alla pagina of 16
1 07/06 ID# M8809511 In-Ground Basketball System Owners Manual Customer Service Center • N53 W24700 South Corporate Circle • Sussex, WI 53089 • U.S.A. READ AND UNDERSTAND OPERATOR'S MANUAL BEFORE USING THIS UNIT. FAILURE TO FOLLOW OPERATING INSTRUCTIONS COULD RESULT IN INJURY OR DAMAGE TO PROPERTY.
2 ID# M8809511 07/06 IMPORT ANT! WRITE MODEL NUMBER FROM BOX ONTO P AGE 1 OF THIS OWNERS MANUAL Owner must ensure that all players know and follow these rules for safe operation of the system. W ARNING • DO NOT HANG on the rim or any part of the system including backboard, support braces or net.
3 07/06 ID# M8809511 24" (61 cm) 36" (91.4 cm) Ensure ground is level with playing surface, then dig pole hole. GROUND SURFACE PLAYING SURFACE 1. Install threaded ends of J-bolts (1) through holes in mounting plate (3) and secure as shown. 2.
4 ID# M8809511 07/06 Fill hole with concrete. Tamp down concrete to release air pockets and build drainage hill. Insert J-bolts (1) from mounting plate (3) into cement as shown. Move assembly around to release any air pockets in cement, then rest mounting plate on cement drainage hill.
5 07/06 ID# M8809511 PLA YIN G SURF A CE Upright pole (5). Assemble lower pole flange onto protruding J-bolts (1) as shown. The flange will then rest on the nuts (2). Secure pole (5) flange to mounting plate (3) as shown. Tighten completely. 6. 7. 5 3 2 6 6 6 2 6 2 6 1 1 5 THREE PEOPLE REQUIRED FOR THIS PROCEDURE.
6 ID# M8809511 07/06 8. 7 14 27 13 27 12 12 27 27 27 27 14 27 13 7 THREE PEOPLE REQUIRED FOR THIS PROCEDURE. F AILURE TO FOLLOW THIS W ARNING COULD RESUL T IN SERIOUS INJUR Y AND/OR PROPERTY DAMAGE. W ARNING! Beginning with upper support arm (8) secure support arms to pole.
7 07/06 ID# M8809511 9. IMPORT ANT! Do Not Over Tighten. 8 14 13 27 27 10 13 27 27 9 Secure backboard to support arms (8 and 9) as shown. Use same hardware combination for attaching both elevator tubes to the backoard.
8 ID# M8809511 07/06 PLA YING SURF A CE 10. Secure jack brackets (21) to to mounting bracket as shown. 21 21 11 1 1. REAR VIEW 13 13 14 Position U-joint of crank jack (20) as shown. Where tubes on crank jack join, hold steady to keep both tubes from rot ating.
9 07/06 ID# M8809511 12. B. TWO PEOPLE REQUIRED FOR THIS PROCEDURE. F AILURE TO FOLLOW THIS W ARNING COULD RESUL T IN SERIOUS INJUR Y AND/OR PROPERTY DAMAGE. W ARNING! 12 14 27 27 13 27 27 13 REAR VIEW IMPORT ANT! Do Not Over Tighten. 9 9 20 20 27 A. Replace spacer in jack (20) with spacer (4).
10 ID# M8809511 07/06 28 13 21 15 15 13 14 20 Some adjustment will be necessary to align the lower crank jack and bushings to jack bracket s (21). NOTE: REAR VIEW TWO PEOPLE REQUIRED FOR THIS PROCEDURE. F AILURE TO FOLLOW THIS W ARNING COULD RESUL T IN SERIOUS INJUR Y AND/OR PROPERTY DAMAGE.
11 07/06 ID# M8809511 7 8 9 1 0 1 0 9 8 7 16 17 16 17 Apply height indicator labels (18 and 19) to height indicators (16). Attach height indicators (16) to lower arm in areas as shown by turning screws (17) into place with a phillips screwdriver . 14.
12 ID# M8809511 07/06 29 22 Attach rim assembly (29). For rim assembly, see instructions included with rim. Rim Assembly 16. IMPORT ANT! Carefully cut and peel protective film away from board prior to att aching rim. Remove rim cover prior to inst alling rim assembly to board.
13 07/06 ID# M8809511 Apply height adjustment label (31) to front of pole as shown. 18. REGULA TION RIM HEIGHT IS 10 FEET (3.05 m). 31 17. Check leveling at this time. Pole (5) should be level in all directions. After system is leveled, completely tighten nuts (2) above pole flange.
14 ID# M8809511 07/06 Rotate crank handle to raise or lower backboard. 20. Secure pole pad (32) as shown. 19. 32 Height Adjustment If height adjustment is difficult to operate, you may have over tightened the areas indicated. NOTE: Pole p ad may NOT be included in this model.
15 07/06 ID# M8809511 Item #10 (4) Item #1 1 (3) Item #17 (4) Item #24 (2) P ARTS LIST HARDW ARE IDENTIFIER (BOL TS) Item Qty. Part No. Description 1 4 200573 J-Bolt, 1/2-13 x 24” Long 2 12 265575 Nut, Hex, 5/8-11 3 1 900661 Anchor Plate 4 1 205714 Spacer, 0.
16 ID# M8809511 07/06 Item #25 (6) Item #26 (4)* Item #27 (28) Item #7 (2) Item #15 (2) * You May Have Extra Parts With This Model. Item #14 (1 1) Item #2 (12) Item #13 (20) Item #22 (4) Item #6 (8) H.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Spalding M8809511 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Spalding M8809511 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Spalding M8809511 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Spalding M8809511 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Spalding M8809511, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Spalding M8809511.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Spalding M8809511. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Spalding M8809511 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
