Manuale d’uso / di manutenzione del prodotto HDW-F500 del fabbricante Sony
Vai alla pagina of 176
OPERA TION MANUAL [English] 1st Edition Serial No. 10101 and Higher HD DIGIT AL VIDEOCASSETTE RECORDER HD W -F500 PARALLEL INTERFACE KIT BKDW-509 HD-525 DOWNCONVERTER BOARD HKDV-501A HD LINE CON.
W ARNING To prevent fire or shock hazard, do not expose the unit to rain or moisture. To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only. For the customers in U.S.A. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
Table of Contents 1 Table of Contents Chapter 1 Overview 1-1 Features ............................................................................................ 1-1 1-1-1 Features of the HDW-F500 .................................................... 1-1 1-1-2 Features of the Control Panel .
T able of Contents 2 Table of Contents Table of Contents 4-3 TC Menu ........................................................................................ 4-20 4-3-1 Setting the Time Data (TIMER SEL/RESET/SET/HOLD) 4-21 4-3-2 Setting the Time Code Reader (TCR SEL) .
Table of Contents 3 Table of Contents 6-1 Basic Automatic Editing ................................................................. 6-1 6-1-1 Overview of Automatic Editing ............................................. 6-1 Chapter 6 Editing ...........
T able of Contents 4 Table of Contents Table of Contents Appendix Maintenance .......................................................................................... A-1 Head Cleaning ................................................................
Chapter 1 Overview Chapter 1 Overview 1-1 Chapter 1 Over vie w 1-1-1 Features of the HD W-F500 The HDW-F500 is a HD digital videocassette recorder using the HDcam format. Comparable to a conventional digital Betacam in size, weight, and ease- of-use, the HDW-F500 is a small, lightweight HD digital VTR using integrated circuit technology.
1-1 Features Chapter 1 Overview 1-2 Chapter 1 Overview Advanced Recording and Playback Functions High-quality digital recording The HDcam system uses a component system to record video signals. An AES/EBU format with a wide dynamic range is used for 4-channel audio recording.
Chapter 1 Overview Chapter 1 Overview 1-3 1-1-2 Features of the Contr ol P anel The BKDW-515 Control Panel provides six menu screens corresponding to the six operation modes to allow fast and easy adjustment of necessary settings, as well as the ability to store menu settings to a memory card for later recall.
1-1 Features Chapter 1 Overview 1-4 Chapter 1 Overview ....................................................................................................................................................................................................
Chapter 1 Overview Chapter 1 Overview 1-5 The following accessories can be used with the HDW- F500. BKDW-509 Parallel (50-pin) Interface Kit A 50-pin parallel interfaces makes the HDW-F500 compatible with different broadcast station systems. HKDV-501A HD-SD Converter Board Allows you to output an NTSC/PAL component or composite signal.
.
Chapter 2 Locations and Functions of Parts and Controls 2-1 Chapter 2 Locations and Functions of Parts and Controls 2-1 Contr ol P anel Chapter 2 Locations and Functions of P ar ts and Contr ols The c.
2-1 Contr ol P anel 2-2 Chapter 2 Locations and Functions of Parts and Controls Chapter 2 Locations and Functions of Parts and Controls 2-1-1 Upper Control P anel Upper control panel 1 DISPLAY FULL/FINE button Changes the display range of the audio level meters.
Chapter 2 Locations and Functions of Parts and Controls 2-3 Chapter 2 Locations and Functions of Parts and Controls 9 Indicator window The following indicators light up to indicate the VTR ’ s status. 4 PHONES level control Adjusts the output level to the PHONES jack.
2-1 Contr ol P anel 2-4 Chapter 2 Locations and Functions of Parts and Controls Chapter 2 Locations and Functions of Parts and Controls !º INPUT SELECT button Selects the type and channel for the audio input signal.
Chapter 2 Locations and Functions of Parts and Controls 2-5 Chapter 2 Locations and Functions of Parts and Controls 2-1-2 Lower Contr ol Panel (Menu Operations Section) Lower control panel (menu opera.
2-1 Contr ol P anel 2-6 Chapter 2 Locations and Functions of Parts and Controls Chapter 2 Locations and Functions of Parts and Controls 1 Menu display Menus selected by pressing the menu buttons appear here.
Chapter 2 Locations and Functions of Parts and Controls 2-7 Chapter 2 Locations and Functions of Parts and Controls 2-1-3 Lower Contr ol Panel (Editing Operations Section) Lower control panel (editing.
2-1 Contr ol P anel 2-8 Chapter 2 Locations and Functions of Parts and Controls Chapter 2 Locations and Functions of Parts and Controls !º Numeric buttons and +/– buttons Press to input time data or edit points data at the cursor position in menu display.
Chapter 2 Locations and Functions of Parts and Controls 2-9 Chapter 2 Locations and Functions of Parts and Controls 2-1-4 Lower Contr ol Panel (T ape T ranspor t Operations Section) Lower control pane.
2-1 Contr ol P anel 2-10 Chapter 2 Locations and Functions of Parts and Controls Chapter 2 Locations and Functions of Parts and Controls @∞ PREROLL button Press to position the tape to the preroll point (a position factory set to five seconds before the IN point).
Chapter 2 Locations and Functions of Parts and Controls 2-11 Chapter 2 Locations and Functions of Parts and Controls 2-1-5 Lower Contr ol Panel (Sear c h Operations Section) Lower control panel (searc.
2-1 Contr ol P anel 2-12 Chapter 2 Locations and Functions of Parts and Controls Chapter 2 Locations and Functions of Parts and Controls #∞ Search dial Rotate to search for edit points. Rotate the dial clockwise for forward playback (the z indicator lights up) or counterclockwise for reverse playback (the Z indicator lights up).
Chapter 2 Locations and Functions of Parts and Controls 2-13 Chapter 2 Locations and Functions of Parts and Controls 2-2 System Set-Up P anel Lift the lower control panel up to its horizontal position to access the system set-up panel.
2-3 Connector Panel 2-14 Chapter 2 Locations and Functions of Parts and Controls Chapter 2 Locations and Functions of Parts and Controls Connector panel 2-3 Connector P anel 8 AUDIO INPUT (AES/EBU) connectors 9 AUDIO OUTPUT (AES/EBU) connectors !º HD SDI INPUT connectors !¡ HD SDI OUTPUT connectors @∞ TIME CODE OUT connector 1 REF.
Chapter 2 Locations and Functions of Parts and Controls 2-15 Chapter 2 Locations and Functions of Parts and Controls 1 REF. OUT 1125 SYNC connectors (BNC) Outputs a trilevel sync signal for the external synchronization. The field frequency is synchronized to the input video signal.
2-3 Connector Panel 2-16 Chapter 2 Locations and Functions of Parts and Controls Chapter 2 Locations and Functions of Parts and Controls !¢ AUDIO INPUT LEVEL/600 Ω termination switches The termination switches should be set for in ANALOG AUDIO INPUT connector according to the audio input level and input impedance.
Chapter 2 Locations and Functions of Parts and Controls 2-17 Chapter 2 Locations and Functions of Parts and Controls @∞ TIME CODE OUT connector (XLR-3-31) Outputs the following time codes according to the VTR operation mode.
.
Chapter 3 Setting Up the VTR 3-1 Chapter 3 Setting Up the VTR 3-1 Connecting External Equipment Chapter 3 Setting Up the VTR 3-1-1 Making Digital Connections This example shows how to connect the HDD/HDDP- 1000 1 inch HD Digital VTR and use it as the player with the HDW-F500 acting as the recorder in the 59.
3-2 Chapter 3 Setting Up the VTR 3-1 Connecting External Equipment Chapter 3 Setting Up the VTR 3-1-2 Making HD Analog Connections This example shows how to connect the VTR when using HD analog audio and video signals in the 60i mode.
Chapter 3 Setting Up the VTR 3-3 Chapter 3 Setting Up the VTR 3-1-3 Making NTSC/P AL Digital Connections This example shows how to connect two VTRs together, using an HDW-F500 as the players and a DVR-2100 D-1 Component Digital VTR as the recorder.
3-4 Chapter 3 Setting Up the VTR 3-1 Connecting External Equipment Chapter 3 Setting Up the VTR Note On the recording VTRs, set 613.TC OUTPUT 3-1-4 Cascade connection This example shows how to connect multiple HDW-F500 VTRs together for simultaneous recording.
Chapter 3 Setting Up the VTR 3-5 Chapter 3 Setting Up the VTR This section describes how reference signals for the video output and servo system are selected.
3-2 Reference Signals f or Video Output and Ser vo System 3-6 Chapter 3 Setting Up the VTR Chapter 3 Setting Up the VTR Reference signal connections For recording signals from a switcher or signal gen.
Chapter 3 Setting Up the VTR 3-7 Chapter 3 Setting Up the VTR For playback Note The following signals can be used as a reference signal. • HD trilevel SYNC signal of an appropriate field frequency for the external synchronization • Black burst signal of 525/59.
3-3 Handling Cassettes 3-8 Chapter 3 Setting Up the VTR Chapter 3 Setting Up the VTR System frequency 29.97/30 Hz 25 Hz 23.98/24 Hz S-size cassette 3-3 Handling Cassettes 3-3-1 Recommended Cassettes Use 1 / 2 inch HDcam cassettes. The maximum recording time is as shown in the following table.
Chapter 3 Setting Up the VTR 3-9 Chapter 3 Setting Up the VTR Removing slack in the tape Press one of the reels in slightly, then carefully rotate it in the direction of the arrow until it stops.
.
Chapter 4 Menu Settings 4-1 Chapter 4 Menu Settings 4-1-1 Menu Configuration This VTR has two kinds of menus. PF1&2 ASSIGN menu This menu contains items that can be registered to the PF1/2 menus. Press the [F4] (PF1&2 ASSIGN) button in the SET UP menu to display this menu.
4-1 Registering and Storing Menu Settings 4-2 Chapter 4 Menu Settings Chapter 4 Menu Settings 2 Press the ALT button. The second page of the HOME menu appears in the display. To return to the first page Press the ALT button again. 3 Press the [F5] (CAP LOCK) button to change the capstan servo lock mode setting.
Chapter 4 Menu Settings 4-3 Chapter 4 Menu Settings 4-1-3 Registering Items to the PF1/2 Menus You can register up to 40 items to the PF (Personal Function) 1/2 menus, including items that are displayed when the ALT button is pressed.
4-1 Registering and Storing Menu Settings 4-4 Chapter 4 Menu Settings Chapter 4 Menu Settings 4-1-4 VTR Memory Bank Function Eight VTR memory banks are provided for storing up to eight sets of menu settings including items registered to the PF1/2 menus with titles.
Chapter 4 Menu Settings 4-5 Chapter 4 Menu Settings 6 Press the [F9] (COPY) button. A message appears in the display asking you to confirm the operation. To cancel the storage operation Press the CLR button. 7 Press the [F9] (COPY) button while holding down the SFT button.
4-1 Registering and Storing Menu Settings 4-6 Chapter 4 Menu Settings Chapter 4 Menu Settings 6 Press the [F9] (COPY) button while holding down the SFT button. The menu settings are recalled from the selected VTR memory bank. When the recalling process has been completed, the title of the VTR bank appears under CURRENT SETUP in the display.
Chapter 4 Menu Settings 4-7 Chapter 4 Menu Settings 4 Move the cursor to the VTR side using the [>] button and use the G and g buttons to move the cursor to the memory bank where the data is to be saved. To store the current VTR menu settings Move the cursor ( z ) to the [C] (CURRENT SETUP) position.
4-1 Registering and Storing Menu Settings 4-8 Chapter 4 Menu Settings Chapter 4 Menu Settings 2 Press the [F2] (MEMORY CARD) button. The MEMORY CARD menu appears in the display. You can access MEMORY CARD menu directly from any menu screen by pressing the ACCESS button.
Chapter 4 Menu Settings 4-9 Chapter 4 Menu Settings 3 Press the [F8] (DIRECTION) button or press the [<] or [>] buttons twice to select the / direction. 4 Move the cursor to the memory card side using the [<] button and use the G or g buttons to place the cursor ( z ) by the memory bank where the settings were saved.
4-1 Registering and Storing Menu Settings 4-10 Chapter 4 Menu Settings Chapter 4 Menu Settings 6 Press the F button to move the cursor ( z ) to the VTR side, then press the G or G button to move the cursor to the VTR memory bank number where the recalled data are to be stored.
Chapter 4 Menu Settings 4-11 Chapter 4 Menu Settings To return to the MEMORY CARD menu Press the [F3] (SHOW SETUP) button again. 4 Press the [F8] (DIRECTION) button or press the [<] or [>] buttons twice to select the / direction. 5 Press the G or g button to move the cursor ( z ) to the number of the memory bank in the memory card.
4-1 Registering and Storing Menu Settings 4-12 Chapter 4 Menu Settings Chapter 4 Menu Settings 4 Press the [F7] (SET LETTER) button . The selected letter is entered. 5 Repeat Steps 3 and 4 to enter more characters. To enter a space Press the [F5] (SPACE) button.
Chapter 4 Menu Settings 4-13 Chapter 4 Menu Settings 4-1-8 Memory Card Data Compatibility Data copied onto a memory card can be used on control panels connected to other HDW-F500 VTRs. Although data is completely compatible between VTRs with different optional equipment, take note of the following.
4-2 HOME Men u 4-14 Chapter 4 Menu Settings Chapter 4 Menu Settings HOME menu display 4-2 HOME Menu The HOME menu sets the basic VTR operation conditions for recording, playback, and editing. The HOME, TC, PF1 and PF2 menus show information that includes the VTR operation mode, time code of the current position, and time code type, etc.
Chapter 4 Menu Settings 4-15 Chapter 4 Menu Settings HOME menu Button Indication Function Settings [F1] PB/EE Selection of output signals PB, EE [F2] REC INH Disables recording off, < all, crash REC, video/CTL, audio/CTL >, [casst] Note The [casst] indicator is only displayed when the record-protect plug is set to prevent recording.
4-2 HOME Men u 4-16 Chapter 4 Menu Settings Chapter 4 Menu Settings VTR SETUP MENU 017. PB/ EE SELECT MENU settings Output signals while the [F1] (PB/EE) button is held down PB/MU EE/EE PB/PB EE/EE EE.
Chapter 4 Menu Settings 4-17 Chapter 4 Menu Settings 4-2-5 Still-Picture Output (FREEZE) For stillpicture output, press the ALT/ [F3] (FREEZE) button. The picture that was playing just before the button was pressed will be frozen on the screen. Make the field or frame selection using the 902.
4-2 HOME Men u 4-18 Chapter 4 Menu Settings Chapter 4 Menu Settings 4-2-6 Selecting the Capstan Ser v o Lock Mode (CAP LOCK) Press the ALT button, then the [F5] (CAP LOCK) button to select the capstan servo lock mode when you edit or play a tape with composite signals.
Chapter 4 Menu Settings 4-19 Chapter 4 Menu Settings 4-2-9 Recalling Edit P oints (LAST EDIT) While editing, you can recall the last edit points by pressing the ALT button, then the [F10] (LAST EDIT) button.
4-3 TC Menu 4-20 Chapter 4 Menu Settings Chapter 4 Menu Settings 4-3 TC Menu The TC menu allows you to set time code-related items through a single menu. The HOME, TC, PF1 and PF2 menus show information that includes the VTR operation mode, time code of the current position, and the time code type, etc.
Chapter 4 Menu Settings 4-21 Chapter 4 Menu Settings 4-3-1 Setting the Time Data (TIMER SEL/RESET/SET/HOLD) The display shows the following types of time data: Time data for IN, OUT, AUDIO IN and AUDIO OUT points are also displayed. Appears whenever a duration between any two edit points (IN, OUT, AUDIO IN or AUDIO OUT points) is displayed.
4-3 TC Menu 4-22 Chapter 4 Menu Settings Chapter 4 Menu Settings Selecting the time code and the user bits to be recorded Use the [F6] (TCG SOURCE), [F7] (TCG MODE), [F9] (DF/NDF), and [F10] (VITC) buttons in the TC menu to specify the time code and the user bits to be recorded.
Chapter 4 Menu Settings 4-23 Chapter 4 Menu Settings Data entry window SET is displayed. ÅIN 00:01:10:00 ÅOUT 00:02:10:00 PLAY LOCK TIMER SEL TC CH.COND GREEN 01 00 30 00 TC TCR VITC 2FD F1 IN 00:01.
4-3 TC Menu 4-24 Chapter 4 Menu Settings Chapter 4 Menu Settings Setting the CTL timer 1 Select CTL using the [F1] (TIMER SEL) button. 2 Enter data in the data entry window using the number buttons. 3 Press the SET button to set the data. 4 Press [F3] (TIMER SET).
Chapter 4 Menu Settings 4-25 Chapter 4 Menu Settings ......................................................................................................................................................................................................
4-3 TC Menu 4-26 Chapter 4 Menu Settings Chapter 4 Menu Settings 4-3-6 Inser ting VITC input sour ce (VITC) Press the [F10] (VITC) button to select the VITC source to be written in the video signal AUX data area. TCG: Inserts values generated by the internal time code generator into the VITC.
Chapter 4 Menu Settings 4-27 Chapter 4 Menu Settings 6 Press the SET button to set the input data. 7 Press the [F2] (PDTIME SET) key. Notes • Once the time code is preset, it cannot be reverted. • Operation information display cannot be displayed while the pull down time code appears.
4-3 TC Menu 4-28 Chapter 4 Menu Settings Chapter 4 Menu Settings 4-3-10 Displa ying the Pull Do wn Time Code (when HKD V -507 is installed) To display the pull down time code, follow the steps below. 1 Press the TC button, then press the ALT button. 2 Press the [F5] (PDTC DISP) key to select “ on ” .
Chapter 4 Menu Settings 4-29 Chapter 4 Menu Settings 1 Types of time data Note When time data or user bits are not read correctly, a “ * ” will be displayed in this block so that the symbols become “ T*R ” , “ U*R ” , etc.
4-3 TC Menu 4-30 Chapter 4 Menu Settings Chapter 4 Menu Settings Operation modes a) Initial speed or memorized speed Display Operation mode A block B block TAPE UNTHREAD Cassette not inserted STANDBY OFF Standby off mode T.
Chapter 4 Menu Settings 4-31 Chapter 4 Menu Settings To display remaining time on the tape Use the 628.REMAIN TIME DISPLAY to display remaining time on the tape. off: Do not display remaining time. 10min: Display remaining time when it is 10 minutes or less.
4-4 CUE Men u 4-32 Chapter 4 Menu Settings Chapter 4 Menu Settings Button Indication Function CUE menu display 4-4 CUE Menu The HDW-F500 allows you to register up to 100 cue points (0 to 99), and to manage cue points in groups of 10 (per page). Cue point settings, deletions, and page settings are done through the CUE menu.
Chapter 4 Menu Settings 4-33 Chapter 4 Menu Settings 4-4-2 Registering Cue P oints There are two ways to register cue points: (1) by direct registration of the tape address when the ENTRY button is pressed, and (2) by the entry of cue point data with the numeric buttons.
4-4 CUE Men u 4-34 Chapter 4 Menu Settings Chapter 4 Menu Settings Registering cue points by the numeric buttons Registering cue points by the numeric buttons 1 Press the ALT button, then the [F8] (PAGE MODE) button or the [F9] (EXTEND MODE) button.
Chapter 4 Menu Settings 4-35 Chapter 4 Menu Settings 4 Enter the cue point data in the data entry window with the numeric buttons, then press the SET button. For example, to enter 00:01:30:00, press 0, 0, 1, 3, 0, 0, 0. (The leading 0 is not required.
4-4 CUE Men u 4-36 Chapter 4 Menu Settings Chapter 4 Menu Settings 4 Press the CLR button then the SET button. “ SET ” appears in the data entry window. 5 Press the ENTRY button. Data for the specified cue number are erased and the data column becomes blank.
Chapter 4 Menu Settings 4-37 Chapter 4 Menu Settings 4-4-6 Bac kspace Editing You can perform backspace editing with the CUE menu. In backspace editing, assemble editing is performed from the recording end point.
4-5 PF1 Menu (F actor y Settings) 4-38 Chapter 4 Menu Settings Chapter 4 Menu Settings 4-5 PF1 Menu (F actory Settings) The PF (Personal Function) 1 menu is used to register frequently used menu items. When shipped from the factory, the PF1 menu contains the adjustment menu for video signals.
Chapter 4 Menu Settings 4-39 Chapter 4 Menu Settings 4-5-3 Adjusting the Output Video Signal (MASTER LEVEL to FINE) Adjusting the output video signal Follow the procedure below to adjust the output video signal. Adjusting the output video signal 1 Press the function button ( [F4] to [F10] ) whose setting you wish to set.
4-5 PF1 Menu (F actor y Settings) 4-40 Chapter 4 Menu Settings Chapter 4 Menu Settings Adjusting the master output level (HD) Make this adjustment with the [F4] (MASTER LEVEL) button.
Chapter 4 Menu Settings 4-41 Chapter 4 Menu Settings Adjusting the R–Y output level (D1) Make this adjustment with the ALT/ [F4] (R – Y LEVEL) buttons. prst: 100% (4000H) Numerical value: 0.0 to 141.3% Adjustable range: – ∞ to +3 dB Adjusting the video output level (D2) Make this adjustment with the ALT/ [F5] (VIDEO LEVEL) buttons.
4-6 PF2 Menu (F actory Settings) 4-42 Chapter 4 Menu Settings Chapter 4 Menu Settings PF2 menu display PF2 menu (factory settings) 4-6 PF2 Menu (F actory Settings) The PF2 menu is used to register frequently used menu items. When shipped from the factory, the PF2 menu contains the adjustment menu for audio signals.
Chapter 4 Menu Settings 4-43 Chapter 4 Menu Settings 4-6-1 Selecting the Audio Input Signal (A-IN CH-1~CH4) Function buttons [F1] (A-IN CH1) to [F4] (A-IN CH4) select the audio input signal for the various channels. SDI: Selects the audio signal input through the HD SDI INPUT connector.
4-7 SET UP Menu 4-44 Chapter 4 Menu Settings Chapter 4 Menu Settings VTR BANK SET UP menu display 4-7 SET UP Menu To activate the SET UP menu Press the SET UP button. To change the SET UP menu page Press the ALT button. “ $ ” indicates that more than one menu page exists.
Chapter 4 Menu Settings 4-45 Chapter 4 Menu Settings Selecting remote operation mode When operating the VTR with an external device, set the [F8] (REMOTE 9-PIN) button or [F9] (REMOTE 50-PIN) button to on. When the [F8] (REMOTE 9-PIN) button is set to on You can operate the VTR with a device connected to the REMOTE1-IN(9P)/OUT(9P) connectors.
4-7 SET UP Menu 4-46 Chapter 4 Menu Settings Chapter 4 Menu Settings 4-7-1 VTR SETUP Menu All menu items required for setting up the VTR operating conditions are displayed in the scrollable VTR SETUP menu. Items which are frequently used can be registered in the PF1/2 menus.
Chapter 4 Menu Settings 4-47 Chapter 4 Menu Settings Category H01~ Menu number Items related to the hours meter 001~ Items related to VTR operations 101~ Items related to operation panels Items relate.
4-7 SET UP Menu 4-48 Chapter 4 Menu Settings Chapter 4 Menu Settings Settings [F1] KEYINH Disables all button operations. on, off [F6] KEY BEEP Sets the keyboard sound. high, low, off [F7] ALARM BEEP Sets the alarm. high, low, off [F8] SCREEN SAVER Sets the screen-saver.
Chapter 4 Menu Settings 4-49 Chapter 4 Menu Settings Disabling the upper and lower control panel buttons Set the [F1] (KEYINH) button to on. You can select buttons to be disabled through 110. KEY INHIBIT SWITCH EFFECTIVE AREA in the VTR SETUP menu. Setting the keyboard sound Press the [F6] (KEY BEEP) button repeatedly.
.
Chapter 5 Recording/Playback 5-1 Chapter 5 Recording/Playback DIGIT AL VIDEO CASSETTE RECORDER HDW -F500 Setting switches and menus 5-1 Preparing for Recor ding Chapter 5 Recor ding/Pla ybac k 5-1-1 Setting Switches and Men us Before recording, set the switches and menus as shown in the diagram below.
5-2 Chapter 5 Recording/Playback 5-1 Preparing f or Recording Chapter 5 Recording/Playback 5-1-2 Selecting A udio Signals This section describes how to select the audio signals for input and monitoring.
Chapter 5 Recording/Playback 5-3 Chapter 5 Recording/Playback To adjust the audio output level of the MONITOR OUTPUT connectors You can make an initial settings to allow the audio output level of the MONITOR OUTPUT connector to be adjusted with the PHONES level control on the upper control panel.
5-4 Chapter 5 Recording/Playback 5-1 Preparing f or Recording Chapter 5 Recording/Playback 5-1-4 Simultaneously Monitoring Playbac k of Video and A udio Signals Being Recorded Monitoring signals being recorded Using the 017.PB/EE SELECT MENU settings, the audio and video signals currently being recorded can be simultaneously checked.
Chapter 5 Recording/Playback 5-5 Chapter 5 Recording/Playback 5-2 Recor ding To record, follow the procedure below. Recording 1 Check that the REC INHIBIT indicator is off, then insert a cassette. For details on inserting a cassette, see Section 3-3-2, “ Inserting and Ejecting Cassettes ” on page 3-8.
5-6 Chapter 5 Recording/Playback 5-1 Preparing for Recor ding Chapter 5 Recording/Playback 5-3 Preparing f or Pla yback 5-3-1 Setting Switc hes and Menus Before starting playback, set the switches and menus as shown in the diagram below. For details, refer to the pages indicated in the parentheses.
Chapter 5 Recording/Playback 5-7 Chapter 5 Recording/Playback 5-3-3 Selecting the HD-SD Con version Mode (when HKD V -501A is installed) When the optional HKDV-501A HD-SD Converter Board is installed in the HDW-F500, the conversion mode can be selected with setting the VTR SETUP menu 754.
5-8 Chapter 5 Recording/Playback 5-1 Preparing for Recor ding Chapter 5 Recording/Playback 4 Press the [F9] (SYSTEM MENU) button. 5 Press the [F1] (ACTIVE LINE) button to select the conversion mode. Pressing the button cycles the settings from 1035, 1080, off.
Chapter 5 Recording/Playback 5-9 Chapter 5 Recording/Playback 5-3-5 Impr oving the V er tical Resolution during Slo w-Motion Pla yback (when HKD V -502 is installed) When the optional HKDV-502 HD Line.
5-10 Chapter 5 Recording/Playback 5-4 Pla ybac k Chapter 5 Recording/Playback 5-4 Playbac k There are four types of playback: • Normal-speed playback • Jog/Shuttle/Variable mode playback • Capstan override playback • DMC (Dynamic Motion Control) playback 5-4-1 Normal-Speed Pla yback Follow the procedure below to play back at normal speed.
Chapter 5 Recording/Playback 5-11 Chapter 5 Recording/Playback Shuttle mode playback Follow the procedure below to play back in shuttle mode. Shuttle mode playback 1 Press the SHUTTLE button so that the SHUTTLE button lights up. The p indicator lights up and the VTR enters still- picture mode.
5-12 Chapter 5 Recording/Playback 5-4 Pla ybac k Chapter 5 Recording/Playback To return to normal-speed playback Press the PLAY button. Note The audio signal output status is specified by the following settings of 017. PB/EE SELECT MENU in the VTR SETUP menu.
Chapter 5 Recording/Playback 5-13 Chapter 5 Recording/Playback 5-4-4 DMC Pla ybac k Overview of DMC playback DMC (Dynamic Motion Control) playback allows you to vary the playback speed in variable mod.
5-14 Chapter 5 Recording/Playback 5-4 Pla ybac k Chapter 5 Recording/Playback Note If the 101.SELECTION FOR SEARCH DIAL ENABLE setting in the VTR SETUP menu is set to dial direct, initial speed settings cannot be made. Change the 101.SELECTION FOR SEARCH DIAL ENABLE setting to via search key.
Chapter 5 Recording/Playback 5-15 Chapter 5 Recording/Playback $$$ Press the PREVIEW button. Preroll time × initial speed IN point Speed variation end point Tape runs at initial speed Playback mode using the memorized speed Playback at normal speed To stop the tape during DMC playback Press the STOP button.
.
Chapter 6 Editing 6-1 Chapter 6 Editing Chapter 6 Editing 6-1-1 Over view of A utomatic Editing Automatic edit modes The VTR provides the following two modes for automatic editing: • Assemble mode New scenes are added to the end of previously recorded scenes.
6-1 Basic A utomatic Editing 6-2 Chapter 6 Editing Chapter 6 Editing DIGITAL VIDEO CASSETTE RECORDER HDW -F500 Setting switches and menus 6-1-2 Setting Switches and Men us Before editing, set the following switches as shown below. REMOTE buttons: 1(9P) button lights up.
Chapter 6 Editing 6-3 Chapter 6 Editing 6-1-3 Selecting the Edit Mode Select assemble or insert mode. Selecting the edit mode Press one of the following buttons to select the respective edit mode: •.
6-1 Basic A utomatic Editing 6-4 Chapter 6 Editing Chapter 6 Editing $$ 44 Setting edit points with the numeric buttons Setting edit points with the numeric buttons 1 Press the RECORDER or PLAYER button to select the VTR for which edit points are to be set.
Chapter 6 Editing 6-5 Chapter 6 Editing Automatic setting of OUT points When the fourth edit point (OUT point) is set, the edit point data is activated and the invalid point is automatically deleted A.
6-1 Basic A utomatic Editing 6-6 Chapter 6 Editing Chapter 6 Editing $$ 44 $$ 44 4 Press the SET button to set the input data. 5 Press the IN (OUT, AUDIO IN or AUDIO OUT) button. The time data for the IN (OUT, AUDIO IN or AUDIO OUT) point appears in the menu display.
Chapter 6 Editing 6-7 Chapter 6 Editing $$ 44 $ 4 $$ 44 Automatic setting of AUDIO OUT points When the sixth edit point (AUDIO OUT point) is set, the edit point data is activated and the invalid AUDIO.
6-1 Basic A utomatic Editing 6-8 Chapter 6 Editing Chapter 6 Editing 6-1-6 Cuing Up and Prer olling You can preroll the tape to a point prior to the edit start point (preroll point), or cue up the tape to any edit point. Follow the procedure below to cue up or preroll the tape.
Chapter 6 Editing 6-9 Chapter 6 Editing 6-1-7 Pre viewing Follow the procedure below to preview the edit Previewing To preview the edit, press the AUTO button to switch to AUTO mode, then press the PREVIEW/REVIEW button. During previewing, the PREVIEW/REVIEW button lights up.
6-1 Basic A utomatic Editing 6-10 Chapter 6 Editing Chapter 6 Editing 6-1-8 Modifying Edit P oints If an edit point is incorrectly set, for example, if an OUT point is located before an IN point, or t.
Chapter 6 Editing 6-11 Chapter 6 Editing Moving an edit point position by one frame at a time Moving an edit point position by one frame at a time 1 Press the RECORDER or PLAYER button to select the VTR on which to modify the edit point. The button lights up.
6-1 Basic A utomatic Editing 6-12 Chapter 6 Editing Chapter 6 Editing 6-1-9 P erf orming Automatic Editing Overview Tape movement during automatic editing a) Preroll time: Factory-set to 5 seconds. Can be set from 0 to 30 seconds, in 1-second steps, through the SET UP menu.
Chapter 6 Editing 6-13 Chapter 6 Editing Monitoring signals during editing During editing, you can monitor the following video and audio signals on a monitor connected to the recorder VTR. • Between preroll and IN points: Playback signal of the recorder VTR can be monitored.
6-1 Basic A utomatic Editing 6-14 Chapter 6 Editing Chapter 6 Editing Modifying edit points for automatic editing later After you perform automatic editing, the time data of IN, OUT, AUDIO IN or AUDIO OUT points remain stored in memory. The stored data can be later used to modify edit points or to execute automatic editing again.
Chapter 6 Editing 6-15 Chapter 6 Editing 6-2 Advanced A utomatic Editing This section describes the following advanced editing methods: • DMC editing • Animation editing • Preread editing 6-2-1 .
6-2 Ad v anced A utomatic Editing 6-16 Chapter 6 Editing Chapter 6 Editing 5 Press the STOP button. The VTR enters STOP mode. 6 Turn the search dial to set the initial speed. The selected speed is displayed in the time data display. 7 Press the PREVIEW/REVIEW and PREROLL buttons at the same time.
Chapter 6 Editing 6-17 Chapter 6 Editing 6-2-2 Animation Editing Animation editing is a form of insert editing which makes it easier to record a succession of still frames in fixed field or frame units. The procedure for editing after selecting animation editing is exactly the same as for normal insert editing.
6-2 Ad v anced A utomatic Editing 6-18 Chapter 6 Editing Chapter 6 Editing 6-2-3 P erforming Preread Editing Video and digital audio signals already recorded on the tape can be used as an edit source for insert editing. This type of editing is called preread editing, as the VTR uses preread heads to read signals in advance.
Chapter 6 Editing 6-19 Chapter 6 Editing 6-3 Man ual Editing Follow the procedure below to perform manual editing. Manual editing 1 Enter jog or shuttle mode to position the tape at a place at least three seconds before the position at which you want to set an edit point.
.
Appendix A-21 Chapter 7 Maintenance Appendix Maintenance Head Cleaning Use the BCT-HD12CL Cleaning Cassette to clean the video and audio heads. Read the instructions included with the cleaning cassette carefully, as improper usage can damage the heads.
A-22 Appendix Appendix Specifications General Record format HDcam Power requirements 100 to 240 V AC ±10%, 50/60 Hz Power consumption 230 W Operating temperature +5 ° C to +40 ° C (+41 ° F to + 10.
Appendix A-23 Appendix Digital audio system Digital audio signal format (CH-1 to CH-4) Sampling frequency 48 kHz (synchronized with video) Quantization 20 bits/sample Wow and flutter Below measurable .
A-24 Appendix Appendix Output connectors HD SDI OUTPUT BNC (4, MONITOR with superimposed text) 1, 2, 3 and MONITOR SDI (1.485 Gbps) (conforms to SMPTE 292M/BTA-S004B) D CONV.
Appendix A-25 Appendix Accessories supplied AC power cord (1) RCC-5G 9-pin remote control cable (1) PSW 4 × 16 screws for rack mounting (4) SRAM 64 KB Memory card (1) Operation Manual (1) Maintenance.
A-26 Appendix Appendix Information on the operational status of the unit and discrepancies between the field frequency of the tape and that of the unit can be shown in the display. Note The operation information can be viewed in any menu except the CUE or SET UP menu.
Appendix A-27 Appendix Display priority of display messages Messages are displayed in the following order of priority: Error messages . Lost lock messages .
A-28 Appendix Appendix ÅIN 00:00:00:00 ÅOUT 00:00:00:00 LOCK DOLBY NR KEY-INH PB/EE CH.COND GREEN DIGITÅL BÅSEBÅLL EDIT SET HOME TCR PLÅY 4FD F1 IN 00:00:00:00 OUT 00:00:00:00 01 Ó 04 µ 58 ß .
Appendix A-29 Appendix A2 DR NOV RAM CHECK SUM ERROR: Error detected while reading machine type data when the unit was turned on. A3 SYS NOV RAM CHECK SUM ERROR: Error detected while reading menu settings data when the unit was turned on. A4 PLAYER CONTROL COMMAND BUFFER FULL: The 9 pin serial communication send buffer for player control is full.
A-30 Appendix Appendix MAINTENANCE INFOMATION DISPLAY OPERATION CH.COND DIAGNOSTICS ERR LOG ROM VER MAINTE EXEC OPTION INFO EXIT TCR 00;00;00;00 DRUM RUNNING THREADING TAPE TRAVEL 529HOURS 34HOURS 20H.
Appendix A-31 Appendix ERROR LOG 1.00:00:00:00 (E) A3 CH.COND DIAGNOSTICS TOTAL 03 PAGE END PAGE TOP ALL CLEAR T C WARNI- NG ERROR TIME FULL MSG CONDI- TION EXIT '97/03/06 10:32:23 TCR 00:00:01:05 SYS NOV RAM CHECK SUM ERR. . . 2.23:59:59:09 (C) 0B VIDEO DATA ERROR 3.
A-32 Appendix Appendix Error Messa ges and Warning Messa g es Clearing warning messages 1 Press the ALT/ [F8] (CANCEL EDIT) button. 2 Select the message to be cleared using the G and g buttons. 3 Press the [F2] (MARK) button. An asterisk “ * ” will appear in front of the message.
Appendix A-33 Appendix Glossar y AES/EBU format A standard format for the transfer of digital audio signals. In this format, two audio signals can be input/output through one XLR-type connector. Assemble editing An edit mode for adding new scenes to the end of previously recorded scenes.
Glossary A-34 Appendix Appendix Non-drop frame mode In this mode, drop frame mode processing is not performed. Since there is no frame cutting, a discrepancy of about 86 seconds occurs each day (in the case of a field frequency of 59.94 Hz) which causes problems when editing programs in units of seconds using the number of frames as a refernce.
Appendix A-35 Appendix Items in the VTR SETUP menu are divided into categories according to type of setting they perform. Descriptions on each item are given below: • Items related to the hours mete.
Menu List A-36 Appendix Appendix The values enclosed in a box are factory settings. Items Related to VTR Operations (001~) Item number Item Settable range Function 001 PRE-READ [off] audio/video audio only video only Selects the pre-read (read-before-write) mode for insert editing.
Appendix A-37 Appendix Item number Item Settable range Function 005 SERVO/AV REFERENCE select [input] auto external The servo reference is determined by the following menu. input: The reference signal is obtained from the HD SDI INPUT connectors or SDTI (OPTION) IN connector.
Menu List A-38 Appendix Appendix Item number Item Settable range Function 009 LOCAL KEY MAP Enables/disables the buttons on this unit when it is in remote control mode. Sub items STOP [disable] enable disable: The STOP button is disabled in remote control mode.
Appendix A-39 Appendix Function Item Settable range Item number 017 PB/EE SELECT MENU Sub items Selects output video and audio signals. STAND BY OFF PB/MU [EE/EE] Selects the video and audio output signals in the “standby off” mode. PB/MU: The playback video signal is output.
Menu List A-40 Appendix Appendix The values enclosed in a box are factory settings. Items Related to Operation P anels (101~) Function Item Settable range 101 SELECTION FOR SEARCH DIAL ENABLE Item number Determines how the unit is set to search mode.
Appendix A-41 Appendix Settable range Item number Item Function Sub items KEY INHIBIT SWITCH EFFECTIVE AREA 110 The enabling or disabling of switches and buttons can be independently specified through each of the following sub- items when item 109 is set to “on”.
Menu List A-42 Appendix Appendix Function Item Settable range Item number 120 WARNING DISPLAY [off] on Selects whether warning messages should be displayed in the lower part of the timecode display for the HOME menu, the TC menu, the PF1 menu, and the PF2 menu.
Appendix A-43 Appendix The values enclosed in a box are factory settings. Items Related to Remote Interface (201~) Item number Item Settable range Function 201 REMOTE 9-PIN [off] on When this is set to “on,” this unit is controlled from the device connected to the REMOTE 1-IN(9P)/OUT(9P) connectors.
Menu List A-44 Appendix Appendix Items Related to Editing (301~) The values enclosed in a box are factory settings. 304 Item number Item Function Settable range 301 EDIT OPERATION MODE film CG [normal] Selects the animation edit mode. For normal editing, use the “normal” setting.
Appendix A-45 Appendix Item Item number Function Settable range The follwing items specifies the allocation of each channel for the analog audio preset of the editor or remote controller when the digital audio signals from the VTR is edited on an editor (BVE-600, etc.
Menu List A-46 Appendix Appendix Specifies the type of editing for digital audio signals. cut edit: Cut editing (discontinuity in audio signal may result at the join, causing noise.) cross fade: Cross-fade (see figure below.) fade in/out: Fade-out and fade-in (see figure below.
Appendix A-47 Appendix Items Related to Prer olling (401~) The values enclosed in a box are factory settings. 401 Item number Item Function FUNCTION MODE AFTER CUE-UP [stop] still Selects the operation mode that the VTR changes to after completing a cue up operation.
Menu List A-48 Appendix Appendix Items Related to Recor ding Protection (501~) The values enclosed in a box are factory settings. Item number Item Function STILL TIMER 0.
Appendix A-49 Appendix Items Related to the Time Code (601~) The values enclosed in a box are factory settings. Item number Item Settable range Function 601 DF/NDF MODE select [dropframe] non-drop frame auto Selects the timing mode for the time code generator and the CTL counter.
Menu List A-50 Appendix Appendix Item number Item Settable range Function 606 TCG MODE select [preset] regene auto Selects the time code to which the internal time code generator synchronizes.
Appendix A-51 Appendix Item number Item Function Settable range Specifies the signal output to the TIME CODE OUT connector when the internal time code generator is in a mode for regenerating the playback time code (i.e. during auto edit mode or when item 607.
Menu List A-52 Appendix Appendix Item number Settable range Item Function 624 CHARACTER TYPE without BG outlined translucent [withBG] Sets the style of text information such as time codes output from the MONITOR connector of HD SDI OUTPUT, the D CONV.
Appendix A-53 Appendix Item number Settable range Item Function 628 REMAIN TIME DISPLAY [off] 10min on Sets whether to display remaining time on the tape in superimposed charecter position. off: Do not display remaining time. 10 min: Display remaining time when it is 10 minutes or less.
Menu List A-54 Appendix Appendix Function Item number Items Related to the Video Control (701~) The values enclosed in a box are the factory settings. Item Settable range 701 VIDEO INPUT select [SDI] SDTI Selects the input video signal. SDI: The SDI video signal input to the HD SDI INPUT connectors.
Appendix A-55 Appendix Item number Item Function Settable range 710 P B LEVEL (HD) preset: 100% (4000H) 0.0% (0H) . . . [100 % ª4000Hº] . . . 141.3% (5A70H) Adjusts the level of the HD video signal output from the HD SDI OUTPUT connectors.
Menu List A-56 Appendix Appendix Item number Item Function Settable range 754 DOWNCONVERTER MODE [EDGE-CROP] LETTER BOX SQUEEZE When an HKDV-501A (optional HD-SD Converter Board) is installed, selects the mode EDGE-CROP: Selects edge crop mode. LETTER BOX: Selects letter box mode.
Appendix A-57 Appendix Item number Item Function Settable range 766 H CROP POSITION preset: 0 –120 . . . [0] . . . 120 When an HKDV-501A (optional HD-SD Converter Board) is installed, ad justs the image enhancer. Adjust s the “H cr op” (cropping position in the horizontal direction when using edge crop mode).
Menu List A-58 Appendix Appendix Item number Item Function Settable range 770 LEVEL DEPEND THRESHOLD preset: 8 0 . . . [8] . . . 15 When an HKDV-501A (optional HD-SD Converter Board) is installed, adjusts the image enhancer. Sets the luminance range for edge enhancement.
Appendix A-59 Appendix Items Related to the A udio Control (801~) The values enclosed in a box are the factory settings. Item Settable range Item number 811 DIGITAL AUDIO FADE TIME 5 ms [10ms] 15 ms 20 ms 25 ms a) 50 ms b) 85 ms 115 ms c) Specifies the fade processing time during cross-fading or fading-in/out of digital audio signals.
Menu List A-60 Appendix Appendix Item Settable range Item number Function 812 AUDIO CH3/4 INPUT SOURCE ARRANGE [CH3/CH4:sw/sw] CH3/CH4 : ch1/sw CH3/CH4 : sw/ch2 CH3/CH4 : ch1/ch2 Select the input signal for digital audio channels 3 and 4. CH3/CH4: sw/sw: The signal that is selected by the upper control panel is input to channels 3 and 4.
Appendix A-61 Appendix Items Related to Digital Processing (901~) The values enclosed in a box are the factory settings. Item Settable range Item number Function 902 FREEZE MODE [field] field1 field2 .
Menu List A-62 Appendix Appendix Item Settable range Item number Function 9 0 5 disable [enable] Enable or disables the stop freeze function. Stop freeze opration • A “ DT picture ” is a frozen picture in noiseless DT playback mode. The picture freezes in frame mode when the dynamic tracking is performing a frame operation.
Appendix A-63 Appendix Items Related to the Pull Down Contr ol (A01~) The values enclosed in a box are the factory settings. Item number Settable range Function Item A01 PD TIME CODE DISPLAY [off] on Sets whether or not to display the pull down time code on the time code display area.
Menu List A-64 Appendix Appendix Other Items (T01~) The values enclosed in a box are the factory settings. Item number Settable range Function Item T01 AUTO REPEAT MODE [off] on Selects the repeating operation in automatic editing. off: Automatic editing is not repeated.
Index Index I-65 Index Inde x A AC IN connector 2-15 ACCESS button 2-6 Adjusting audio playback level 5-6 output video signal 4-39 recording level 5-3 ALARM indicator 2-6 ALT button 2-6 Assemble editi.
Inde x Index I-66 Index list A-14 PANEL SETUP menu 4-48 PF1 menu 4-38 PF2 menu 4-42 registering items to the PF1/2 menus 4-3 Moisture condensation A-1 MONITOR OUTPUT connectors 2-16 MONITOR SELECT but.
∇ indicates the existence of other menu levels. ALT Menu F1 F2 F3 F4 F5 F6 F7 F8 F9 F10 F1 F2 F3 F4 F5 F6 F7 F8 F9 F10 HOME RECINH ASSEM- BLE INS TC INS VIDEO INS A-CH1 INS A-CH2 INS A-CH3 INS A-CH4.
.
The material contained in this manual consists of information that is the property of Sony Corporation and is intended solely for use by the purchasers of the equipment described in this manual.
Son y Cor poration Broadcasting & Professional Systems Company HDW-F500 (UC, ) 3-203-128- 01 (1) Printed in Japan 1999.09.13 1999.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Sony HDW-F500 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Sony HDW-F500 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Sony HDW-F500 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Sony HDW-F500 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Sony HDW-F500, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Sony HDW-F500.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Sony HDW-F500. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Sony HDW-F500 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
