Manuale d’uso / di manutenzione del prodotto 82S6XL090A del fabbricante Solid State Logic
Vai alla pagina of 30
E Signature™ Channel Owner ’ s Manual.
.
Solid State Logic Super -Analogue™ Outboar d Owner ’s Manual 82S6XL090A XL ogic SIGNATURE CHANNEL.
XLogic E Signature™ Channel Owner ’ s Manual As resear ch and development is a continual process, Solid State Logic r eserves the right to change the features and specifications described her ein without notice or obligation E&OE Initial Release (Rev .
Page 1 Contents 1.0 Introduction 3 2.0 Safety Considerations 4 Safety W arnings 4 3.0 Installation 6 Setting the mains voltage selector 6 Mounting 7 Connections 7 4.0 Operation 9 Input Section 9 Listen Mic Compressor 9 Dynamics Section 10 Compressor/Limiter 10 Expander/Gate 1 1 Filter Section 1 1 Equaliser Section 12 Output Section 12 5.
Page 2 XLogic E Signature™ Channel (front) XLogic E Signature™ Channel (rear) Solid State Logic XL ogic SIGNATURE CHANNEL INPUT LCOMP DRIVE MIC LINE 3RD 2ND LESS MORE +20 -20 +70 +20 0 DYNAMICS RE.
Page 3 Introduction 1.0 Introduction The XLogic E Signature Channel unit brings the classic sound of the original early 1980s E Series console to the outboard rack of today’s artists and pr oducers.
Page 4 XLogic E Signature™ Channel Owner ’ s Manual 2.0 Safety considerations This section contains definitions and warnings, and practical information to ensure a safe working envir onment. Please take time to read this section befor e undertaking any installation work.
Page 5 Safety Considerations Mains Supply and Phases Solid State Logic equipment is designed for connection to a single phase supply with the Neutral conductor at earth potential – category TN – and is fitted with a protective fuse in the Live conductor only .
Page 6 XLogic E Signature™ Channel Owner ’ s Manual 3.0 Installation 3.1 V oltage Selection Before connecting the mains supply ensur e that the voltage range selector next to the IEC socket on the r ear of the unit is correctly set. The input setting must be confirmed befor e applying power .
Page 7 3.2 Mounting This unit is designed to be rack-mounted. It is 1 RU (44.5mm/1.75 inch) high, its depth is: 325 mm/12.8 inches not including heatsink.
Page 8 XLogic E Signature™ Channel Owner ’ s Manual XLogic E Signature™ Channel Block Diagram ADC Option Drive Mic Gain Mic Amp 1 Mic Amp 2 Mic In Line Gain Line Amp Line In ON LINE PAD 48V IN P.
Page 9 Installation and Operation 4.0 Operation The XLogic E Signature Channel unit is a 1U rack mounting unit containing a complete set of signal pr ocessing based upon the SL 4000 E Series channel strip – Input, Compressor/Limiter , Expander/Gate, Hi and Lo pass Filters and Equaliser .
Page 10 XLogic E Signature™ Channel Owner ’ s Manual 4.3 Dynamics Section The Dynamics section of the XLogic E Signature Channel unit comprises a compr essor/limiter and an expander/gate, both of which use the same gain change element.
Page 11 Installation and Operation 4.5 Expander/Gate The Expander/Gate section can act either as a ∞ :1 Gate or , when the EXP switch is pr essed, as a 2:1 Expander . RANGE – Determines the depth of gating or expansion. When turned fully anti-clockwise, the Expander/Gate section will be inactive.
Page 12 XLogic E Signature™ Channel Owner ’ s Manual 4.7 Equaliser Section The XLogic E Signature Channel unit equaliser section defaults to the original ‘Br own Knob’ circuit that was standard on all early pr oduction E Series consoles.
Page 13 Installation and Operation 5.0 Signal Routing Channel Processing Order There ar e two switches that control the or der of the signal pr ocessing elements.
Page 14 XLogic E Signature™ Channel Owner ’ s Manual Stop looking – we left this page blank….
Page 15 Appendix Appendix A – Internal Links and Fuses Fuses (Mains Inlet) The mains inlet contains a single 1 amp 1.25" time delay fuse (SSL Part No. 35FJJ310). T o change it disconnect the mains inlet, then using a small screwdriver prise open the mains selector cover (see illustration on page 6.
Page 16 XLogic E Signature™ Channel Owner ’ s Manual Appendix B – Connector Details Link Location: Rear Panel Conn' Type: TRS Jack Socket Pin Description Tip Link Bus * Ring Link Bus * Slee.
Page 17 Appendix Appendix C – Performance Specification The following pages contain audio performance specification figures for the XLogic E Signatur e Channel unit. No other Solid State Logic products ar e covered by this document and the performance of other Solid State Logic products can not be inferr ed from the data contained her ein.
Page 18 XLogic E Signature™ Channel Owner ’ s Manual Microphone Input 2 (Electronically Balanced) Measurement Conditions Signal applied to Mic Input and measured at Output. Pad switched out and Mic Gain contr ol set to +20dB. Gain Continuously variable from +20dB to +70dB Independently switchable 22dB Pad available Input Impedance > 1.
Page 19 Appendix Equaliser This is a four band equaliser that can be switched between two differ ent sets of curves; one based on SSL ’s ‘02’ (‘Brown Knob’) EQ and the other based on the latest version of the classic ‘242’ E Series (‘Black Knob’) EQ.
Page 20 XLogic E Signature™ Channel Owner ’ s Manual Dynamics The unit contains a complete dynamics section, the functions of which split into two areas; a Compressor/Limiter and an Expander/Gate.
Page 21 Appendix Appendix D - Calibration Information The XLogic E Signature Channel unit is factory calibrated and should only need calibration if a potentiometer or other component has been replaced or if it is suspected that ther e is a problem with calibration.
Page 22 XLogic E Signature™ Channel Owner ’ s Manual Meter Calibration Equipment Required: Calibrated audio oscillator and audio level meter T est Signal: 1kHz sinewave @ +24dBu Input and Output: Oscillator to Line Input and Output to the audio level meter Unit Setup: 1.
Page 23 Appendix 4. Switch BLK in and re-adjust HMF Frequency for maximum level. 5. Adjust VR16 for +18dBu ±0.25dB. 6. Reset HMF Gain to its centre indent position and release the BLK switch. Re- check the audio level meter for 0dBu. HF EQ – Maximum Gain Adjustment: 1.
Page 24 XLogic E Signature™ Channel Owner ’ s Manual Appendix E – Physical specification * Depth: 363mm / 14.3 inches casing and heatsink, excluding front panel knob(s) and rear connectors 425mm / 16.75 inches including connectors, excluding front panel knob(s) Height: 44.
Page 25 Appendix Notes.
Page 26 XLogic E Signature™ Channel Owner ’ s Manual.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Solid State Logic 82S6XL090A è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Solid State Logic 82S6XL090A - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Solid State Logic 82S6XL090A imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Solid State Logic 82S6XL090A ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Solid State Logic 82S6XL090A, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Solid State Logic 82S6XL090A.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Solid State Logic 82S6XL090A. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Solid State Logic 82S6XL090A insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
