Manuale d’uso / di manutenzione del prodotto YZ16335BVE, YZ16385BVE del fabbricante Snapper
Vai alla pagina of 37
Safety Instructions & Operator’s Manual for SCRAMBLER HYDRO DRIVE SERIES 5 MODELS YZ16335BVE YZ16385BVE MODEL NUMBER EXPLANATION Y Z 16 33 5 B V E MODEL DESIGNATION ENGINE OPTIONS DRIVE SYSTEM TYPE ENGINE TYPE ENGINE HORSE POWER SERIES DESIGNATION CUTTING WIDTH Y – SCRAMBLER Z – Zero Turning Radius 16 – 16.
2 IMPORTANT SAFETY INSTRUCTIONS WARNING: This pow erful cutting machine is capable of amputating hands and feet and can throw objects that can cause injury and damage! Failure to comply w ith the follow ing SAFETY instructions could result in serious injury or death to the operator or other persons.
3 IMPORTANT SAFETY INSTRUCTIONS PREPARATION (Continued From Previous Page) 7. Keep people and pets out of mow ing area. Immediately STOP blades, STOP engine, and STOP machine if anyone enters the area. 8. Check shields, deflectors, sw itches, blade controls and other safety dev ices frequently for proper operation and location.
4 IMPORTANT SAFETY INSTRUCTIONS MAINTENANCE 1. DO NOT store machine or fuel container inside w here fumes may reach an open flame, spark or pilot light such as in a w ater heater, furnace, clothes dryer or other gas appliance. Allow engine to cool before storing machine in an enclosure.
5 TABLE OF CONTENTS IMPORTANT SAFETY INSTRUCTIO NS ........................................................................ 2-4 TABLE OF CO NTENTS ...................................................................................................... 5 SECTION 1 - FAMI LIARIZATI ON.
6 Section 1 - FAMILIARIZATION FIGURE 1.1 1. 1 INTRODUCTION This manual has been prepared for the operator’s of the SNAPPER SCRAMBLER. Its purpose, aside from recommending standard operating procedures and routine service requirements, is to promote SAFETY through the use of accepted operating practices.
7 Section 2 - OPERATING INSTRUCTIONS 2.1 PRE-START CHECK LIST Make the following checks and perform the service required before each start-up. 2.1.1. Check tires and add or release air as needed to bring pressure to 12 P.S.I. in front and 12 P.S.I. in rear tires.
8 Section 2 - OPERATING INSTRUCTIONS IMPORTANT: This SCRAMBLER is equipped w ith hydrostatic driv e. The forw ard, rearw ard and steering movement of the machine is controlled by a joystick lever. Joy stick operations should be performed only from the operator’s position in the seat.
9 Section 2 - OPERATING INSTRUCTIONS WARNING DO NOT operate blades in reverse. STOP BLADES. LOOK and SEE behind and down for children, pets and hazards before and w hile backing. 2.2.3. MOWER BLADE 1. With engine running, move engine speed control to the Rabbit or “fast” position.
10 Section 2 - OPERATING INSTRUCTIONS 2.3.5. CUTTING HEIGHT ADJUSTMENT This machine has seven different cutting height positions. IMPORTANT: When positioning the cutting deck into a higher cutting position, pull up on the deck lift handle only, it is not necessary to pull up on the release lever at the same time.
11 Section 3 - MAINTENANCE 3.1 INTRODUCTION To retain the quality of the SCRAMBLER, use genuine SNAPPER replacement parts only. Contact a local SNAPPER dealer for parts and service assistance. For the correct part or information for a particular mower, always mention the model and serial number.
12 Section 3 - MAINTENANCE WARNING DO NOT attempt any adjustments, maintenance, service or repairs with the engine running. Stop engine. Stop blade. Engage parking brake. Remov e key. Remove spark plug wire from spark plug and secure aw ay from plug. Engine and components are HOT.
13 Section 3 - MAINTENANCE WARNING DO NOT attempt any adjustments, maintenance, service or repairs with the engine running. Stop engine. Stop blade. Engage parking brake. Remov e key. Remove spark plug wire from spark plug and secure aw ay from plug. Engine and components are HOT.
14 Section 3 - MAINTENANCE WARNING DO NOT attempt any adjustments, maintenance, service or repairs with the engine running. Stop engine. Stop blade. Engage parking brake. Remov e key. Remove spark plug wire from spark plug and secure aw ay from plug. Engine and components are HOT.
15 Section 3 - MAINTENANCE WARNING DO NOT attempt any adjustments, maintenance, service or repairs with the engine running. Stop engine. Stop blade. Engage parking brake. Remov e key. Remove spark plug wire from spark plug and secure aw ay from plug. Engine and components are HOT.
16 Section 4 - ADJUSTMENTS & REPAIR WARNING DO NOT attempt any adjustments, maintenance, service or repairs with the engine running. Stop engine. Stop blade. Engage parking brake. Remov e key. Remove spark plug wire from spark plug and secure aw ay from plug.
17 Section 4 - ADJUSTMENTS & REPAIR WARNING DO NOT attempt any adjustments, maintenance, service or repairs with the engine running. Stop engine. Stop blade. Engage parking brake. Remov e key. Remove spark plug wire from spark plug and secure aw ay from plug.
18 Section 4 - ADJUSTMENTS & REPAIR WARNING DO NOT attempt any adjustments, maintenance, service or repairs with the engine running. Stop engine. Stop blade. Engage parking brake. Remov e key. Remov e spark plug w ire from spark plug and secure aw ay from plug.
19 Section 4 - ADJUSTMENTS & REPAIR WARNING DO NOT attempt any adjustments, maintenance, service or repairs with the engine running. Stop engine. Stop blade. Engage parking brake. Remov e key. Remove spark plug wire from spark plug and secure aw ay from plug.
20 Section 4 - ADJUSTMENTS & REPAIR WARNING DO NOT attempt any adjustments, maintenance, service or repairs with the engine running. Stop engine. Stop blade. Engage parking brake. Remov e key. Remove spark plug wire from spark plug and secure aw ay from plug.
21 Section 4 - ADJUSTMENTS & REPAIR WARNING DO NOT attempt any adjustments, maintenance, service or repairs with the engine running. Stop engine. Stop blade. Engage parking brake. Remov e key. Remov e spark plug w ire from spark plug and secure aw ay from plug.
22 Section 4 - ADJUSTMENTS & REPAIR WARNING DO NOT attempt any adjustments, maintenance, service or repairs with the engine running. Stop engine. Stop blade. Engage parking brake. Remov e key. Remove spark plug wire from spark plug and secure aw ay from plug.
23 Section 4 - ADJUSTMENTS & REPAIR WARNING DO NOT attempt any adjustments, maintenance, service or repairs with the engine running. Stop engine. Stop blade. Engage parking brake. Remov e key. Remov e spark plug w ire from spark plug and secure aw ay from plug.
24 Section 4 - ADJUSTMENTS & REPAIR 4.5.5. BATTERY TESTING There are two types of battery tests: Unloaded and Loaded. The unloaded test is the procedure that will be discussed. It’s the simplest and most commonly used. An unloaded test is made on a battery without discharging current.
25 TROUBLESHOOTING PROBLEM PROBABLE CAUSE CORRECTIVE ACTION Starter Will Not Crank 1. Battery dead. 1. Service battery. Engine 2. Blown fuse. 2. Replace fuse. 3. Electrical connections loose or corroded. 3. C l ean and check connections for good contact.
26 TROUBLESHOOTING PROBLEM PROBABLE CAUSE CORRECTIVE ACTION Excessive Vibration 1. Damaged, out of balance or bent mo w er blades. 1. Service mower blade(s). 2. Loose blade components. 2. Service and tighten loose parts. 3. Loose or missing air lift (if equipped).
27 SERVICE SCHEDULE ITEM SERVICE PERFORMED REF. EACH USE 5 HRS 25 HRS 50 HRS 100 HRS EACH SEASON Engine Oil Check Oil Level Page 7 X Initial Oil Change Page 11 X Periodic Oil Change Page 12 X* Oil Fil.
28 2 YEAR LIMITED WARRANTY For two (2) years from purchase date for the orig inal purchaser's residential, non-commercial use, SNAPPER , through any authorized SNAPPER dealer will replace, free o.
29 PRIMARY MAINTENANCE.
30 PRIMARY MAINTENANCE.
31 PRIMARY MAINTENANCE.
32 PRIMARY MAINTENANCE.
33 SNAPPER PRODUCT REGISTRATION FORM IMPORTANT: KEEP THIS INFORMATION FOR YOUR PERSONAL RECORDS (Complete the following informa tion on your Snapper purchase) Model Number ____________________________.
34 NOTES ___________________________________________________________________ ___________________________________________________________________ _______________________________________________________.
35 NOTES ___________________________________________________________________ ___________________________________________________________________ _______________________________________________________.
36 NOTES ___________________________________________________________________ ___________________________________________________________________ _______________________________________________________.
37 Safety Instructions & Operator’s Manual for SCRAMBLER HYDRO DRIVE SERIES 5 IMPORTANT Snapper products are built using engines that meet or exceed all applicable emissions requirements on the date manufactured. The labels on those engines contai n very important emissions information and critical safety warnings.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Snapper YZ16335BVE, YZ16385BVE è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Snapper YZ16335BVE, YZ16385BVE - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Snapper YZ16335BVE, YZ16385BVE imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Snapper YZ16335BVE, YZ16385BVE ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Snapper YZ16335BVE, YZ16385BVE, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Snapper YZ16335BVE, YZ16385BVE.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Snapper YZ16335BVE, YZ16385BVE. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Snapper YZ16335BVE, YZ16385BVE insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
