Manuale d’uso / di manutenzione del prodotto SERIES 16 250816B del fabbricante Snapper
Vai alla pagina of 112
Safety Instructions & Operator's Manual for REAR ENGINE RIDING MOWER SERIES 16 MODELS 250816B N250816B 250816BE N250816BE 281016BE N281016BE 301016BE 301216BE 331416BVE 331416KVE PRECIX BODYI.
IMPORTANT SAFETY INSTRUCTIONS WARNING: This powerful cutting machine is capable of amputating hands and feet and can throw objects that can cause injury and damage! Failure to comply with the following SAFETY instructions could result in sedous injury or death to the operator or other persons.
Section 1 - FAMILIARIZATION FUEL VENT TANK REAR BUMPER FUEL FILLER STEERING WHEEL F OPERATOR'S SEAT TRANSMISSION SHIFT; PANEL (See Inset) DECK LIFT LEVER CLUTCH/BRAKE PEDAL CHUTE DEFLECTOR CONTROL PANEL IGNITION SWITCH ENGINE SPEED CQ_TROL BRAKE LEVER 1 I I MOWER DECK I I LEVER FIGURE 1.
Section 2 -OPERATING INSTRUCTIONS 2.1 PRE-START CHECK UST 2.2 Make the following checks and perform the service required before each start-up. 2.1.1. Check tires and add or release air as needed to bring pressure to 15 psi in front and 10 psi in rear tires.
Section 2 - OPERATING INSTRUCTIONS 2.3 STARTING & OPERATION 2.3.1 ENGINE (ELECTRIC START) IMPORTANT: When the ignition key is turned to "START", the engine will turn over, but will not start unless the Clutch/Brake pedal is pressed all the way down, the Blade Lever is in the "OFF" position (See Figure 2.
Section 2- OPERATING INSTRUCTIONS 2.3.1 ENGINE (ELECTRIC START) (Continued) 8. Should the battery be too weak to start the engine, use the instructions shown below, 2.3.2., ENGINE (MANUAL START) to manually start the electric start en- gines. 9. On Model 331416BVE, the engine is equipped with a fuel shut-off solenoid.
Section 2 - OPERATING INSTRUCTIONS /_ CAUTION /'_ Before leaving the Rear Engine Rider with the engine running, STOP the blade, shift to neutral and engage the park brake. 2.4 STOPPING 2.4.1. ENGINE 1. Stop engine by turning key to the "OFF" position.
Section 2 - OPERATING INSTRUCTIONS 2.4.4. PARK BRAKE (Continued) 2. Release park brake by pushing down on the Clutch/Brake Pedal to release park brake lever. See Figure 2.15. PUSH CLUTCWBRAKE PEDAL ALL THE WAY DOWN 2.4.6. WHEEL DRIVE 1. With engine running, adjust engine speed con- trol to "FAST" position.
Section 3 - MAINTENANCE 3.1 INTRODUCTION To retain the quality of the Rear Engine Rider, use genuine SNAPPER replacement parts only. Contact a local SNAPPER dealer for parts and service assistance. For the correct part or information for a particular Rear Engine Riding Mower, always mention the model and sedal number.
Section 3 - MAINTENANCE 3.2.3. CHECK MOWER DRIVE BELT 1. Drive Belt Cover Removal a. Lower deck to lowest setting. b. Remove four self-tapping screws, two on each side of mower drive belt cover. See Figure 3.3. c. Slide cover back and rotate out on left side of mower deck.
Section 3 - MAINTENANCE 3.3.2. MOWER COMPONENTS (Continued) d. Close vent on fuel filler cap. e. Carefully stand Rear Engine Rider on rear bumper. f. Clean underside of mower deck, removing all accumulation of grass clippings and debds. g. Lower Rear Engine Rider to ground and clean top of deck, removing all grass clippings and debris.
Section 3 - MAINTENANCE DIFFERENTIAL . I FIGURE 3.9 Chain Case a. Check fill/level plug for damage. If signs of wear or cracks are visible, replace plug with new plug. See Figure 3.10. b. To check lubricant in chain case, remove fill/level plug and look for lubricant on the internal components of the chain case.
Section 3 - MAINTENANCE 3.5 3.6 EVERY TWO YEARS 3.5.3. Transmission shift lever and detent. 3.5.4. Clutch disc. 3.5.5. Clutch Yoke (See Figure 4.18 on Page 18). 3.5.6. Mower deck linkage and pivot areas. STORAGE (OUT OF SEASON) If desired, the Rear Engine Rider can be stored on the rear bumper.
Section 4 - ADJUSTMENTS & REPAIR Before performing any service or maintenance I procedures, always remove key from ignition I switch, remove spark plug wire from spark plug and I secure spark plug wire away from spark plug.
Section 4 - ADJUSTMENTS & REPAIR CAUTION Before performing any service or maintenance procedures, always remove key from ignition switch, remove spark plug wire from spark plug and secure spark plug wire away from spark plug. 4.2.2. BLADE BRAKE ADJUSTMENT 1.
Section 4 - ADJUSTMENTS & REPAIR LOOSEN SHOULDER BOLT 4.2.4. MOWER DECK ADJUSTMENT (LEVELNESS) 1. Side-To-Side Before making deck leveling adjustments, check the tire pressure. Front tires 15 psi, rear tires 10 psi. If tires are properly inflated and mowing is still uneven, adjust side-to-side deck levelness as follows: a.
Section 4 - ADJUSTMENTS & REPAIR 4.2.5. MOWER DECK TIMING ROD ADJUSTMENT The mower deck timing rod is pre-adjusted at the factory. It is set to maintain the deck in the same attitude through all heights of cut. If suspecting the timing rod requires adjustment, contact an authorized SNAPPER dealer for service.
Section 4 - ADJUSTMENTS & REPAIR CAUTION Before attempting any adjustments or repairs, stop the engine, remove the key, remove the spark plug wire from the spark plug, and secure spark plug wire away from spark plug. 1. Follow procedures for standing Rear Engine Rider on rear bumper.
Section 4 - ADJUSTMENTS & REPAIR HOUSING CABLE COTTER-, 3. Measure the distance between end of clutch/brake cable and bottom of housing. Measurement should be no less than 112" and no greater than 3/4". See inset, Figure 4.18. CHAIN- CASE HOUSING COTTER- PIN FIGURE 4.
Section 4 - ADJUSTMENTS & REPAIR 3. Inspect condition of blade. Refer to Figure 4.20. 4. If blade is in good condition, sharpen at 22 to 28 degrees.
Section 4 -ADJUSTMENTS & REPAIR 4.6.2. BELT REPLACEMENT (Continued) 9. Adjust bait guide. See Figure 4.25 for proper bait-to-belt guide clearances. 10. Check mower drive belt tension and adjust if necessary. Refer to 4.2.1., MOWER DRIVE BELT ADJUSTMENT on Page 13.
Section 4 - ADJUSTMENTS & REPAIR CAUTION The electrolyte (acid) produces a highly explosive gas. Keep all sparks, flame and fire away from area when charging battery or when handling electrolyte or battery. Electrolyte (acid) is a highly corrosive liquid.
Section 4 - ADJUSTMENTS & REPAIR 4.6.5. BATTERY TESTING Methods of Checking Battery Condition State of Charcje 100% Charged w/Sulfate Stop 100% Charged 75% Charged 50% Charged 25% Charged 0% Charcjed Syringe Hydrometer 1.280 1.265 1.210 1.160 1.120 Less than 1.
MAINTENANCE SCHEDULE SUBJECT Engine Engine Engine Air Pre-Cleaner Air Cleaner Spark Plug Fuel Filter Engine Cooling System Battery Battery Tires Drive Belts Mower Blades Mower Deck Lubrication Points .
SNAPPER. 5 - 2 YEAR LIMITED WARRANTY COMPONENT PARTS - 5 YEARS For five (5) years from purchase date for original purchaser's residential non-commercial _' use, Snapper, through any Snapper dealer will replace free of charge any part or parts found upon examination by the factory to be defective in material or workmanship or both.
SERVICE NOTES i.
SERVICE NOTES.
Safety Instructions & Operator's Manual for • REAR ENGINE RIDING MOWER SERIES 16 The engine exhaust from this product contains chemicals known to the State of I AWARNING: California to cause cancer, birth defects or other reproductive harm.
Safety Instructions & Operator's Manual for REAR ENGINE RIDING MOWER SERIES 16 MODELS 250816B N250816B 250816BE N250816BE 281016BE N281016BE 301016BE 301216BE 331416BVE 331416KVE PRECIX BODYI.
IMPORTANT SAFETY INSTRUCTIONS WARNING: This powerful cutting machine is capable of amputating hands and feet and can throw objects that can cause injury and damage! Failure to comply with the following SAFETY instructions could result in sedous injury or death to the operator or other persons.
Section 1 - FAMILIARIZATION FUEL VENT TANK REAR BUMPER FUEL FILLER STEERING WHEEL F OPERATOR'S SEAT TRANSMISSION SHIFT; PANEL (See Inset) DECK LIFT LEVER CLUTCH/BRAKE PEDAL CHUTE DEFLECTOR CONTROL PANEL IGNITION SWITCH ENGINE SPEED CQ_TROL BRAKE LEVER 1 I I MOWER DECK I I LEVER FIGURE 1.
Section 2 -OPERATING INSTRUCTIONS 2.1 PRE-START CHECK UST 2.2 Make the following checks and perform the service required before each start-up. 2.1.1. Check tires and add or release air as needed to bring pressure to 15 psi in front and 10 psi in rear tires.
Section 2 - OPERATING INSTRUCTIONS 2.3 STARTING & OPERATION 2.3.1 ENGINE (ELECTRIC START) IMPORTANT: When the ignition key is turned to "START", the engine will turn over, but will not start unless the Clutch/Brake pedal is pressed all the way down, the Blade Lever is in the "OFF" position (See Figure 2.
Section 2- OPERATING INSTRUCTIONS 2.3.1 ENGINE (ELECTRIC START) (Continued) 8. Should the battery be too weak to start the engine, use the instructions shown below, 2.3.2., ENGINE (MANUAL START) to manually start the electric start en- gines. 9. On Model 331416BVE, the engine is equipped with a fuel shut-off solenoid.
Section 2 - OPERATING INSTRUCTIONS /_ CAUTION /'_ Before leaving the Rear Engine Rider with the engine running, STOP the blade, shift to neutral and engage the park brake. 2.4 STOPPING 2.4.1. ENGINE 1. Stop engine by turning key to the "OFF" position.
Section 2 - OPERATING INSTRUCTIONS 2.4.4. PARK BRAKE (Continued) 2. Release park brake by pushing down on the Clutch/Brake Pedal to release park brake lever. See Figure 2.15. PUSH CLUTCWBRAKE PEDAL ALL THE WAY DOWN 2.4.6. WHEEL DRIVE 1. With engine running, adjust engine speed con- trol to "FAST" position.
Section 3 - MAINTENANCE 3.1 INTRODUCTION To retain the quality of the Rear Engine Rider, use genuine SNAPPER replacement parts only. Contact a local SNAPPER dealer for parts and service assistance. For the correct part or information for a particular Rear Engine Riding Mower, always mention the model and sedal number.
Section 3 - MAINTENANCE 3.2.3. CHECK MOWER DRIVE BELT 1. Drive Belt Cover Removal a. Lower deck to lowest setting. b. Remove four self-tapping screws, two on each side of mower drive belt cover. See Figure 3.3. c. Slide cover back and rotate out on left side of mower deck.
Section 3 - MAINTENANCE 3.3.2. MOWER COMPONENTS (Continued) d. Close vent on fuel filler cap. e. Carefully stand Rear Engine Rider on rear bumper. f. Clean underside of mower deck, removing all accumulation of grass clippings and debds. g. Lower Rear Engine Rider to ground and clean top of deck, removing all grass clippings and debris.
Section 3 - MAINTENANCE DIFFERENTIAL . I FIGURE 3.9 Chain Case a. Check fill/level plug for damage. If signs of wear or cracks are visible, replace plug with new plug. See Figure 3.10. b. To check lubricant in chain case, remove fill/level plug and look for lubricant on the internal components of the chain case.
Section 3 - MAINTENANCE 3.5 3.6 EVERY TWO YEARS 3.5.3. Transmission shift lever and detent. 3.5.4. Clutch disc. 3.5.5. Clutch Yoke (See Figure 4.18 on Page 18). 3.5.6. Mower deck linkage and pivot areas. STORAGE (OUT OF SEASON) If desired, the Rear Engine Rider can be stored on the rear bumper.
Section 4 - ADJUSTMENTS & REPAIR Before performing any service or maintenance I procedures, always remove key from ignition I switch, remove spark plug wire from spark plug and I secure spark plug wire away from spark plug.
Section 4 - ADJUSTMENTS & REPAIR CAUTION Before performing any service or maintenance procedures, always remove key from ignition switch, remove spark plug wire from spark plug and secure spark plug wire away from spark plug. 4.2.2. BLADE BRAKE ADJUSTMENT 1.
Section 4 - ADJUSTMENTS & REPAIR LOOSEN SHOULDER BOLT 4.2.4. MOWER DECK ADJUSTMENT (LEVELNESS) 1. Side-To-Side Before making deck leveling adjustments, check the tire pressure. Front tires 15 psi, rear tires 10 psi. If tires are properly inflated and mowing is still uneven, adjust side-to-side deck levelness as follows: a.
Section 4 - ADJUSTMENTS & REPAIR 4.2.5. MOWER DECK TIMING ROD ADJUSTMENT The mower deck timing rod is pre-adjusted at the factory. It is set to maintain the deck in the same attitude through all heights of cut. If suspecting the timing rod requires adjustment, contact an authorized SNAPPER dealer for service.
Section 4 - ADJUSTMENTS & REPAIR CAUTION Before attempting any adjustments or repairs, stop the engine, remove the key, remove the spark plug wire from the spark plug, and secure spark plug wire away from spark plug. 1. Follow procedures for standing Rear Engine Rider on rear bumper.
Section 4 - ADJUSTMENTS & REPAIR HOUSING CABLE COTTER-, 3. Measure the distance between end of clutch/brake cable and bottom of housing. Measurement should be no less than 112" and no greater than 3/4". See inset, Figure 4.18. CHAIN- CASE HOUSING COTTER- PIN FIGURE 4.
Section 4 - ADJUSTMENTS & REPAIR 3. Inspect condition of blade. Refer to Figure 4.20. 4. If blade is in good condition, sharpen at 22 to 28 degrees.
Section 4 -ADJUSTMENTS & REPAIR 4.6.2. BELT REPLACEMENT (Continued) 9. Adjust bait guide. See Figure 4.25 for proper bait-to-belt guide clearances. 10. Check mower drive belt tension and adjust if necessary. Refer to 4.2.1., MOWER DRIVE BELT ADJUSTMENT on Page 13.
Section 4 - ADJUSTMENTS & REPAIR CAUTION The electrolyte (acid) produces a highly explosive gas. Keep all sparks, flame and fire away from area when charging battery or when handling electrolyte or battery. Electrolyte (acid) is a highly corrosive liquid.
Section 4 - ADJUSTMENTS & REPAIR 4.6.5. BATTERY TESTING Methods of Checking Battery Condition State of Charcje 100% Charged w/Sulfate Stop 100% Charged 75% Charged 50% Charged 25% Charged 0% Charcjed Syringe Hydrometer 1.280 1.265 1.210 1.160 1.120 Less than 1.
MAINTENANCE SCHEDULE SUBJECT Engine Engine Engine Air Pre-Cleaner Air Cleaner Spark Plug Fuel Filter Engine Cooling System Battery Battery Tires Drive Belts Mower Blades Mower Deck Lubrication Points .
SNAPPER. 5 - 2 YEAR LIMITED WARRANTY COMPONENT PARTS - 5 YEARS For five (5) years from purchase date for original purchaser's residential non-commercial _' use, Snapper, through any Snapper dealer will replace free of charge any part or parts found upon examination by the factory to be defective in material or workmanship or both.
SERVICE NOTES i.
SERVICE NOTES.
Safety Instructions & Operator's Manual for • REAR ENGINE RIDING MOWER SERIES 16 The engine exhaust from this product contains chemicals known to the State of I AWARNING: California to cause cancer, birth defects or other reproductive harm.
Safety Instructions & Operator's Manual for REAR ENGINE RIDING MOWER SERIES 16 MODELS 250816B N250816B 250816BE N250816BE 281016BE N281016BE 301016BE 301216BE 331416BVE 331416KVE PRECIX BODYI.
IMPORTANT SAFETY INSTRUCTIONS WARNING: This powerful cutting machine is capable of amputating hands and feet and can throw objects that can cause injury and damage! Failure to comply with the following SAFETY instructions could result in sedous injury or death to the operator or other persons.
Section 1 - FAMILIARIZATION FUEL VENT TANK REAR BUMPER FUEL FILLER STEERING WHEEL F OPERATOR'S SEAT TRANSMISSION SHIFT; PANEL (See Inset) DECK LIFT LEVER CLUTCH/BRAKE PEDAL CHUTE DEFLECTOR CONTROL PANEL IGNITION SWITCH ENGINE SPEED CQ_TROL BRAKE LEVER 1 I I MOWER DECK I I LEVER FIGURE 1.
Section 2 -OPERATING INSTRUCTIONS 2.1 PRE-START CHECK UST 2.2 Make the following checks and perform the service required before each start-up. 2.1.1. Check tires and add or release air as needed to bring pressure to 15 psi in front and 10 psi in rear tires.
Section 2 - OPERATING INSTRUCTIONS 2.3 STARTING & OPERATION 2.3.1 ENGINE (ELECTRIC START) IMPORTANT: When the ignition key is turned to "START", the engine will turn over, but will not start unless the Clutch/Brake pedal is pressed all the way down, the Blade Lever is in the "OFF" position (See Figure 2.
Section 2- OPERATING INSTRUCTIONS 2.3.1 ENGINE (ELECTRIC START) (Continued) 8. Should the battery be too weak to start the engine, use the instructions shown below, 2.3.2., ENGINE (MANUAL START) to manually start the electric start en- gines. 9. On Model 331416BVE, the engine is equipped with a fuel shut-off solenoid.
Section 2 - OPERATING INSTRUCTIONS /_ CAUTION /'_ Before leaving the Rear Engine Rider with the engine running, STOP the blade, shift to neutral and engage the park brake. 2.4 STOPPING 2.4.1. ENGINE 1. Stop engine by turning key to the "OFF" position.
Section 2 - OPERATING INSTRUCTIONS 2.4.4. PARK BRAKE (Continued) 2. Release park brake by pushing down on the Clutch/Brake Pedal to release park brake lever. See Figure 2.15. PUSH CLUTCWBRAKE PEDAL ALL THE WAY DOWN 2.4.6. WHEEL DRIVE 1. With engine running, adjust engine speed con- trol to "FAST" position.
Section 3 - MAINTENANCE 3.1 INTRODUCTION To retain the quality of the Rear Engine Rider, use genuine SNAPPER replacement parts only. Contact a local SNAPPER dealer for parts and service assistance. For the correct part or information for a particular Rear Engine Riding Mower, always mention the model and sedal number.
Section 3 - MAINTENANCE 3.2.3. CHECK MOWER DRIVE BELT 1. Drive Belt Cover Removal a. Lower deck to lowest setting. b. Remove four self-tapping screws, two on each side of mower drive belt cover. See Figure 3.3. c. Slide cover back and rotate out on left side of mower deck.
Section 3 - MAINTENANCE 3.3.2. MOWER COMPONENTS (Continued) d. Close vent on fuel filler cap. e. Carefully stand Rear Engine Rider on rear bumper. f. Clean underside of mower deck, removing all accumulation of grass clippings and debds. g. Lower Rear Engine Rider to ground and clean top of deck, removing all grass clippings and debris.
Section 3 - MAINTENANCE DIFFERENTIAL . I FIGURE 3.9 Chain Case a. Check fill/level plug for damage. If signs of wear or cracks are visible, replace plug with new plug. See Figure 3.10. b. To check lubricant in chain case, remove fill/level plug and look for lubricant on the internal components of the chain case.
Section 3 - MAINTENANCE 3.5 3.6 EVERY TWO YEARS 3.5.3. Transmission shift lever and detent. 3.5.4. Clutch disc. 3.5.5. Clutch Yoke (See Figure 4.18 on Page 18). 3.5.6. Mower deck linkage and pivot areas. STORAGE (OUT OF SEASON) If desired, the Rear Engine Rider can be stored on the rear bumper.
Section 4 - ADJUSTMENTS & REPAIR Before performing any service or maintenance I procedures, always remove key from ignition I switch, remove spark plug wire from spark plug and I secure spark plug wire away from spark plug.
Section 4 - ADJUSTMENTS & REPAIR CAUTION Before performing any service or maintenance procedures, always remove key from ignition switch, remove spark plug wire from spark plug and secure spark plug wire away from spark plug. 4.2.2. BLADE BRAKE ADJUSTMENT 1.
Section 4 - ADJUSTMENTS & REPAIR LOOSEN SHOULDER BOLT 4.2.4. MOWER DECK ADJUSTMENT (LEVELNESS) 1. Side-To-Side Before making deck leveling adjustments, check the tire pressure. Front tires 15 psi, rear tires 10 psi. If tires are properly inflated and mowing is still uneven, adjust side-to-side deck levelness as follows: a.
Section 4 - ADJUSTMENTS & REPAIR 4.2.5. MOWER DECK TIMING ROD ADJUSTMENT The mower deck timing rod is pre-adjusted at the factory. It is set to maintain the deck in the same attitude through all heights of cut. If suspecting the timing rod requires adjustment, contact an authorized SNAPPER dealer for service.
Section 4 - ADJUSTMENTS & REPAIR CAUTION Before attempting any adjustments or repairs, stop the engine, remove the key, remove the spark plug wire from the spark plug, and secure spark plug wire away from spark plug. 1. Follow procedures for standing Rear Engine Rider on rear bumper.
Section 4 - ADJUSTMENTS & REPAIR HOUSING CABLE COTTER-, 3. Measure the distance between end of clutch/brake cable and bottom of housing. Measurement should be no less than 112" and no greater than 3/4". See inset, Figure 4.18. CHAIN- CASE HOUSING COTTER- PIN FIGURE 4.
Section 4 - ADJUSTMENTS & REPAIR 3. Inspect condition of blade. Refer to Figure 4.20. 4. If blade is in good condition, sharpen at 22 to 28 degrees.
Section 4 -ADJUSTMENTS & REPAIR 4.6.2. BELT REPLACEMENT (Continued) 9. Adjust bait guide. See Figure 4.25 for proper bait-to-belt guide clearances. 10. Check mower drive belt tension and adjust if necessary. Refer to 4.2.1., MOWER DRIVE BELT ADJUSTMENT on Page 13.
Section 4 - ADJUSTMENTS & REPAIR CAUTION The electrolyte (acid) produces a highly explosive gas. Keep all sparks, flame and fire away from area when charging battery or when handling electrolyte or battery. Electrolyte (acid) is a highly corrosive liquid.
Section 4 - ADJUSTMENTS & REPAIR 4.6.5. BATTERY TESTING Methods of Checking Battery Condition State of Charcje 100% Charged w/Sulfate Stop 100% Charged 75% Charged 50% Charged 25% Charged 0% Charcjed Syringe Hydrometer 1.280 1.265 1.210 1.160 1.120 Less than 1.
MAINTENANCE SCHEDULE SUBJECT Engine Engine Engine Air Pre-Cleaner Air Cleaner Spark Plug Fuel Filter Engine Cooling System Battery Battery Tires Drive Belts Mower Blades Mower Deck Lubrication Points .
SNAPPER. 5 - 2 YEAR LIMITED WARRANTY COMPONENT PARTS - 5 YEARS For five (5) years from purchase date for original purchaser's residential non-commercial _' use, Snapper, through any Snapper dealer will replace free of charge any part or parts found upon examination by the factory to be defective in material or workmanship or both.
SERVICE NOTES i.
SERVICE NOTES.
Safety Instructions & Operator's Manual for • REAR ENGINE RIDING MOWER SERIES 16 The engine exhaust from this product contains chemicals known to the State of I AWARNING: California to cause cancer, birth defects or other reproductive harm.
Safety Instructions & Operator's Manual for REAR ENGINE RIDING MOWER SERIES 16 MODELS 250816B N250816B 250816BE N250816BE 281016BE N281016BE 301016BE 301216BE 331416BVE 331416KVE PRECIX BODYI.
IMPORTANT SAFETY INSTRUCTIONS WARNING: This powerful cutting machine is capable of amputating hands and feet and can throw objects that can cause injury and damage! Failure to comply with the following SAFETY instructions could result in sedous injury or death to the operator or other persons.
Section 1 - FAMILIARIZATION FUEL VENT TANK REAR BUMPER FUEL FILLER STEERING WHEEL F OPERATOR'S SEAT TRANSMISSION SHIFT; PANEL (See Inset) DECK LIFT LEVER CLUTCH/BRAKE PEDAL CHUTE DEFLECTOR CONTROL PANEL IGNITION SWITCH ENGINE SPEED CQ_TROL BRAKE LEVER 1 I I MOWER DECK I I LEVER FIGURE 1.
Section 2 -OPERATING INSTRUCTIONS 2.1 PRE-START CHECK UST 2.2 Make the following checks and perform the service required before each start-up. 2.1.1. Check tires and add or release air as needed to bring pressure to 15 psi in front and 10 psi in rear tires.
Section 2 - OPERATING INSTRUCTIONS 2.3 STARTING & OPERATION 2.3.1 ENGINE (ELECTRIC START) IMPORTANT: When the ignition key is turned to "START", the engine will turn over, but will not start unless the Clutch/Brake pedal is pressed all the way down, the Blade Lever is in the "OFF" position (See Figure 2.
Section 2- OPERATING INSTRUCTIONS 2.3.1 ENGINE (ELECTRIC START) (Continued) 8. Should the battery be too weak to start the engine, use the instructions shown below, 2.3.2., ENGINE (MANUAL START) to manually start the electric start en- gines. 9. On Model 331416BVE, the engine is equipped with a fuel shut-off solenoid.
Section 2 - OPERATING INSTRUCTIONS /_ CAUTION /'_ Before leaving the Rear Engine Rider with the engine running, STOP the blade, shift to neutral and engage the park brake. 2.4 STOPPING 2.4.1. ENGINE 1. Stop engine by turning key to the "OFF" position.
Section 2 - OPERATING INSTRUCTIONS 2.4.4. PARK BRAKE (Continued) 2. Release park brake by pushing down on the Clutch/Brake Pedal to release park brake lever. See Figure 2.15. PUSH CLUTCWBRAKE PEDAL ALL THE WAY DOWN 2.4.6. WHEEL DRIVE 1. With engine running, adjust engine speed con- trol to "FAST" position.
Section 3 - MAINTENANCE 3.1 INTRODUCTION To retain the quality of the Rear Engine Rider, use genuine SNAPPER replacement parts only. Contact a local SNAPPER dealer for parts and service assistance. For the correct part or information for a particular Rear Engine Riding Mower, always mention the model and sedal number.
Section 3 - MAINTENANCE 3.2.3. CHECK MOWER DRIVE BELT 1. Drive Belt Cover Removal a. Lower deck to lowest setting. b. Remove four self-tapping screws, two on each side of mower drive belt cover. See Figure 3.3. c. Slide cover back and rotate out on left side of mower deck.
Section 3 - MAINTENANCE 3.3.2. MOWER COMPONENTS (Continued) d. Close vent on fuel filler cap. e. Carefully stand Rear Engine Rider on rear bumper. f. Clean underside of mower deck, removing all accumulation of grass clippings and debds. g. Lower Rear Engine Rider to ground and clean top of deck, removing all grass clippings and debris.
Section 3 - MAINTENANCE DIFFERENTIAL . I FIGURE 3.9 Chain Case a. Check fill/level plug for damage. If signs of wear or cracks are visible, replace plug with new plug. See Figure 3.10. b. To check lubricant in chain case, remove fill/level plug and look for lubricant on the internal components of the chain case.
Section 3 - MAINTENANCE 3.5 3.6 EVERY TWO YEARS 3.5.3. Transmission shift lever and detent. 3.5.4. Clutch disc. 3.5.5. Clutch Yoke (See Figure 4.18 on Page 18). 3.5.6. Mower deck linkage and pivot areas. STORAGE (OUT OF SEASON) If desired, the Rear Engine Rider can be stored on the rear bumper.
Section 4 - ADJUSTMENTS & REPAIR Before performing any service or maintenance I procedures, always remove key from ignition I switch, remove spark plug wire from spark plug and I secure spark plug wire away from spark plug.
Section 4 - ADJUSTMENTS & REPAIR CAUTION Before performing any service or maintenance procedures, always remove key from ignition switch, remove spark plug wire from spark plug and secure spark plug wire away from spark plug. 4.2.2. BLADE BRAKE ADJUSTMENT 1.
Section 4 - ADJUSTMENTS & REPAIR LOOSEN SHOULDER BOLT 4.2.4. MOWER DECK ADJUSTMENT (LEVELNESS) 1. Side-To-Side Before making deck leveling adjustments, check the tire pressure. Front tires 15 psi, rear tires 10 psi. If tires are properly inflated and mowing is still uneven, adjust side-to-side deck levelness as follows: a.
Section 4 - ADJUSTMENTS & REPAIR 4.2.5. MOWER DECK TIMING ROD ADJUSTMENT The mower deck timing rod is pre-adjusted at the factory. It is set to maintain the deck in the same attitude through all heights of cut. If suspecting the timing rod requires adjustment, contact an authorized SNAPPER dealer for service.
Section 4 - ADJUSTMENTS & REPAIR CAUTION Before attempting any adjustments or repairs, stop the engine, remove the key, remove the spark plug wire from the spark plug, and secure spark plug wire away from spark plug. 1. Follow procedures for standing Rear Engine Rider on rear bumper.
Section 4 - ADJUSTMENTS & REPAIR HOUSING CABLE COTTER-, 3. Measure the distance between end of clutch/brake cable and bottom of housing. Measurement should be no less than 112" and no greater than 3/4". See inset, Figure 4.18. CHAIN- CASE HOUSING COTTER- PIN FIGURE 4.
Section 4 - ADJUSTMENTS & REPAIR 3. Inspect condition of blade. Refer to Figure 4.20. 4. If blade is in good condition, sharpen at 22 to 28 degrees.
Section 4 -ADJUSTMENTS & REPAIR 4.6.2. BELT REPLACEMENT (Continued) 9. Adjust bait guide. See Figure 4.25 for proper bait-to-belt guide clearances. 10. Check mower drive belt tension and adjust if necessary. Refer to 4.2.1., MOWER DRIVE BELT ADJUSTMENT on Page 13.
Section 4 - ADJUSTMENTS & REPAIR CAUTION The electrolyte (acid) produces a highly explosive gas. Keep all sparks, flame and fire away from area when charging battery or when handling electrolyte or battery. Electrolyte (acid) is a highly corrosive liquid.
Section 4 - ADJUSTMENTS & REPAIR 4.6.5. BATTERY TESTING Methods of Checking Battery Condition State of Charcje 100% Charged w/Sulfate Stop 100% Charged 75% Charged 50% Charged 25% Charged 0% Charcjed Syringe Hydrometer 1.280 1.265 1.210 1.160 1.120 Less than 1.
MAINTENANCE SCHEDULE SUBJECT Engine Engine Engine Air Pre-Cleaner Air Cleaner Spark Plug Fuel Filter Engine Cooling System Battery Battery Tires Drive Belts Mower Blades Mower Deck Lubrication Points .
SNAPPER. 5 - 2 YEAR LIMITED WARRANTY COMPONENT PARTS - 5 YEARS For five (5) years from purchase date for original purchaser's residential non-commercial _' use, Snapper, through any Snapper dealer will replace free of charge any part or parts found upon examination by the factory to be defective in material or workmanship or both.
SERVICE NOTES i.
SERVICE NOTES.
Safety Instructions & Operator's Manual for • REAR ENGINE RIDING MOWER SERIES 16 The engine exhaust from this product contains chemicals known to the State of I AWARNING: California to cause cancer, birth defects or other reproductive harm.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Snapper SERIES 16 250816B è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Snapper SERIES 16 250816B - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Snapper SERIES 16 250816B imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Snapper SERIES 16 250816B ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Snapper SERIES 16 250816B, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Snapper SERIES 16 250816B.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Snapper SERIES 16 250816B. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Snapper SERIES 16 250816B insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
