Manuale d’uso / di manutenzione del prodotto 8526, 9528, 10530, 11532 del fabbricante Snapper
Vai alla pagina of 34
OPERA T OR’S MANU AL Lar g e Frame Sno wthr o wer s 8526 Models Mfg. No. Description 1694984 L8526E, 8.5HP Snowthrower 1695082 L8526EX, 8.5HP Snowthrower (CE) 1694993 85268E, 8.5HP Snowthrower 1695093 E85268E, 8.5HP Snowthrower (CE) 9528 Models Mfg.
T able of Contents 1 CONTENTS: Safety Rules & Inf ormation General ............................................................2 T raining ............................................................4 Preparation ..................................
2 TP 600-3606-05-LW-SMA Operating Safety Congratulations on purchasing a superior-quality piece of lawn and garden equipment. Our products are designed and manu- factured to meet or exceed all industry standards for safety. Power equipment is only as safe as the operator.
3 Moving Parts This equipment has many moving parts that can injure you or someone else. However, if you are standing in the operator’s position, and follow all the rules in this book, the unit is safe to operate. The auger and impeller have spinning parts that can amputate hands and feet.
4 This machine is capable to amputating hands and feet and throwing objects. Read these safety rules and follow them closely. Failure to obey these rules could result in loss of control of unit, severe personal injury or death to you, or bystanders, or damage to property or equipment.
5 8. Always follow the engine manual instructions for stor- age preparations before storing the unit for both short and long term periods. 9. Always follow the engine manual instructions for proper start-up procedures when returning the unit to service.
Decals 6 DECALS This unit has been designed and manufactured to pro- vide you with the safety and reliability you would expect from an industry leader in outdoor power equipment.
Decals 7 Part No. 1733059 - DANGER / WARNING Main Dash Decal, CE, w/o Easy Turn Part No. 1733060 - DANGER / WARNING Main Dash Decal, CE, w/ Easy Turn Part No. 1732618 Shift Decal Part No. 1727208 Auger Danger Decal Part No. 1727207 Discharge Chute Danger Decal Part No.
Safety Icons 8 WARNING: READ OPERATOR’S MANUAL. Read and understand the Operator’s Manual before using this machine. DANGER: THROWN OBJECTS. This machine is capable of throwing objects and debris. Keep bystanders away. WARNING: REMOVE KEY BEFORE SERVICING.
Identification Numbers 9 When contacting your authorized dealer for replace- ment parts, service, or information you MUST have these numbers. Record your model name/number, manufacturer’s identi- fication numbers, and engine serial numbers in the space provided for easy access.
10 Features, Controls, & Operation CONTR OL LOCA TIONS The information below briefly describes the function of individual controls. Starting, stopping, and driving require the combined use of several controls applied in specific sequences. To learn what combination and sequence of controls to use for various tasks see the OPERATION section.
Features & Controls 11 Fuel Fuel tank filler cap (see illustration). Note: The fuel shut off valve is located under the fuel tank or on the front of the engine. Close the valve when the snowthrower is not in use. Open the valve before starting. Primer Button When pressed, the primer button provides initial fuel to help start a cold engine.
Operation 12 GENERAL OPERA TION CHECKS BEFORE EA CH ST ART -UP 1. Make sure all safety guards are in place and all nuts, bolts and clips are secure. 2. Check to make sure that the clean-out is attached to the auger housing. Do not operate the machine with- out the clean-out tool properly stored on the auger housing.
Operation 13 ST ARTING CONTR OLS See Figure 1 for the following instructions. Electric Start A. Electric Start Button - The Electric Start Button (A) activates an electric starter mounted to the engine, eliminating the need to pull the starter han- dle.
Operation 14 5. When BOTH levers are depressed, the Free-Hand™ Control is activated. This allows Auger Engage Control to be released — YET AUGER ROTATION WILL CONTINUE — until the Free-Hand™ Control is released. 6. Select forward or reverse speeds as needed using the Speed Selector (A, Figure 2).
Operation 15 GR OUND SPEED SELECT OR Use the speed selector (A, Figure 2) to control the drive speed of the snowthrower. There are five forward speeds and two reverse speeds. Use the lower speeds to blow deep or wet snow. Use the higher speeds to blow light snow or to drive the snow- thrower without blowing snow.
Operation 16 EASY TURN™ FREEWHEELING AND TRA CTION DRIVE LOCK While Clearing Snow: For easy turning when using the snowthrower, squeeze the Easy Turn™ lever (Figure 5). Engaging the Easy Turn™ lever releases the left traction wheel but allows the right wheel to continue driving (Figure 5).
Operation 17 AFTER EA CH USE Normal use of the snowthrower may result in a build-up of packed snow in and around the starter cord housing and around engine controls.
18 Regular Maintenance A UGER GEAR CASE LUBRICA TION 1. Place the snowthrower on a level surface. 2. Remove the pipe plug (A, Figure 8). 3. Check the lubricant level. It should be level with the lower edge of the plug opening. If not, add Lithium grease.
LUBRICA TION Remove wheels and grease axles once each year. Apply 5W-30 synthetic motor oil to the friction disk drive hex shaft (A, Figure 10). Apply medium weight (10W) oil to points shown (See Figures 9-12). Generally, all moving metal parts should be oiled where contact is made with other parts.
Regular Maintenance 20 CHECK / LUBRICA TE FREE-HAND LINKA GE Check the function of the Free-Hand controls: the con- trols should function as described in the CONTROLS section. It is critical for the safe operation of the unit that the controls disengage when released.
21.
22 T roubleshooting, Adjustments, Service W ARNING Before performing any adjustment or service to snowthrower, stop the engine and wait for moving parts to stop. Remove the key. To prevent accidental starting, disconnect the spark plug wire and fasten away from the plug.
T roubleshooting 23 PROBLEM POSSIBLE CA USE REMED Y Auger rotates, but snow is not thrown far enough 1. Chute deflector too low. 1. Adjust deflector as necessary. 2. Engine speed too slow. 2. Set speed to full throttle. 3. Ground speed too fast. 3. Use slower speed selector setting.
Adjustments 24 A UGER DRIVE ADJUSTMENT 1. Check that the auger cable (A, Figure 15) is on top of cable button (B) as show in Figure 15. 2. With the drive lever released, the hook (B, Figure 16b) should barely touch the lever (C) without raising it. There can be a maximum 1/32” clearance as shown.
Adjustments 25 Note: If the cable is too slack the unit will not drive. If the cable is too tight the drive will be engaged without push- ing the handles down. 4. Slide the cable boot (A) over the cable adjustment bracket. Run-In Adjustment ALL MODELS 1.
Adjustments 26 Figure 20. Cable Adjustment A. Adjustment Nut B. Jam Nut A B Figure 21. Belt Cover A. Belt Cover B. Screws A B B Figure 22. Auger Belt Deflection A. Engine Drive Pulley B. Idler Pulley (Engaged Position) C. Auger Drive Pulley D. Nut E. Auger Belt B C A 1/2” (12.
Adjustments & Service 27 Figure 23. Shear Pins A. Shear Pins B. Cotter Pins A B A B SHEAR PIN REPLA CEMENT Under most circumstances, if the auger strikes an object which could cause damage to the unit, the shear pin will break. (This protects the gear box and other parts from damage.
Service 28 BEL T REPLA CEMENT A uger Drive Belt The drive belts are of special construction and must be replaced with original factory replacement belts available from your nearest authorized service center. Some steps require the assistance of a second person.
Adjustments & Service 29 Figure 29. Frame and Axle Housing A. Upper Capscrews B. Lower Capscrews C. Auger Housing D. Frame B Figure 27. Spout Rotator Rod A. Special Nut B. Cover C. Hair Pin D. Spout Rotator Rod A B C D A B D A D C Figure 28. Install Spout Rotator Rod A.
Service 30 T raction Drive Belt If the snow thrower will not move forward, check the trac- tion drive belt for wear or damage. If the traction drive belt is worn or damaged, replace the belt as follows. 1. Disconnect the spark plug wire. 2. Remove the auger drive belt.
Specifications 31 ENGINE: 8.5 HP* Briggs & Stratton Make Briggs & Stratton Model Power Built Horsepower 8.5 @ 3600 rpm Displacement 15.2 Cu. in (249 cc) Oil Capacity 19 oz. (,56 L) 9.5 HP* Briggs & Stratton Make Briggs & Stratton Model Intek Snow Horsepower 9.
Parts & Accessories 32 REPLA CEMENT P ARTS Replacement parts are available from your authorized dealer. Always use genuine Simplicity / Snapper Service Parts. TECHNICAL MANU ALS Additional copies of this manual are available, as well as fully illustrated parts lists.
© Copyright 2006, Briggs & Stratton. All Rights Reserved. Printed in USA. MANUFACTURING, INC. 500 N Spring Street / PO Box 997 Port Washington, WI 53074-0997 www.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Snapper 8526, 9528, 10530, 11532 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Snapper 8526, 9528, 10530, 11532 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Snapper 8526, 9528, 10530, 11532 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Snapper 8526, 9528, 10530, 11532 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Snapper 8526, 9528, 10530, 11532, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Snapper 8526, 9528, 10530, 11532.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Snapper 8526, 9528, 10530, 11532. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Snapper 8526, 9528, 10530, 11532 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.