Manuale d’uso / di manutenzione del prodotto 7800392 del fabbricante Snapper
Vai alla pagina of 16
8/2008 1 TP 300-5412---ZT-SN Axion / 150Z Series Form No. 7102754 Briggs & Stratton Yard Power Products Group Copyright © 2008 Briggs & Stratton Corporation Milwaukee, WI USA. All Rights Reserved This Dealer Setup Instruction covers the following products: Initial setup Model.
Axion / 150Z Series TP 300-5412---ZT-SN 8/2008 2 T ABLE OF CONTENTS: SAFETY RULES .................................................................3 SETUP PROCEDURES Quick Setup List ................................................................6 Uncrating .
Axion / 150Z Series 8/2008 3 TP 300-5412---ZT-SN SAFETY R ULES GENERAL OPERA TION 1. Read, understand, and follow all instructions in the manual and on the unit before starting. 2. Do not put hands or feet near rotating parts or under the machine. Keep clear of the discharge opening at all times.
Axion / 150Z Series TP 300-5412---ZT-SN 8/2008 4 CHILDREN Tragic accidents can occur if the operator is not alert to the presence of children. Children are often attracted to the unit and the mowing activity. Never assume that children will remain where you last saw them.
Axion / 150Z Series 8/2008 5 TP 300-5412---ZT-SN SER VICE AND MAINTENANCE Safe Handling of Gasoline 1. Extinguish all cigarettes, cigars, pipes, and other sources of ignition. 2. Use only approved gasoline containers. 3. Never remove the gas cap or add fuel with the engine running.
Axion / 150Z Series TP 300-5412---ZT-SN 8/2008 6 Quick Setup List P age Setup Procedure Steps to P erform 7 Uncrating ❏ Remov e crate & banding. ❏ Place transmissions in R OLL RELEASE position & roll off skid.
8/2008 7 TP 300-5412---ZT-SN Axion / 150Z Series Uncrating 1. Using a reciprocating utility saw or equivalent, cut crate away from bottom skid. Remove crate. Remove plastic wrap. 2. Cut any banding securing the unit. IMPORT ANT NO TE When cutting crate from bottom skid, use caution around tires and mower rollers.
TP 300-5412---ZT-SN 8/2008 8 Axion / 150Z Series W ARNING Corrosion hazard. Batteries contain acid. Always keep the battery upright and do not spill the electrolyte. Avoid contact with skin and eyes. Explosion hazard. Changing the battery produces explosive hydrogen gas.
8/2008 9 TP 300-5412---ZT-SN Axion / 150Z Series 5/16-1 8 x 3/4 14-19 ft. lbs. 19-25 N.m. Installing the Seat 1. Raise the seat base. 2. Align the holes in the seat bottom with the holes in the seat base. 3. Secure the seat to the seat base with four 5/16-18 x 3/4” bolts.
Axion / 150Z Series TP 300-5412---ZT-SN 8/2008 10 Installing the Seat Safety Switc h 1. Squeeze the side clips of the safety switch (A, Figure 6), and insert the switch into the slot (B) in the seat bottom. Be sure to slide the switch fully forward. 2.
Axion / 150Z Series 8/2008 11 TP 300-5412---ZT-SN 5/16-1 8 x 1-3/4 5/16-1 8 15-17 ft. lbs. 20-23 N.m. Setting Up the Gr ound Speed Contr ol Le vers 1. Loosen (do not remove) the hardware securing the ground speed control levers to the lever bases.
TP 300-5412---ZT-SN 8/2008 12 Axion / 150Z Series 30-40 ft. lbs. 41-54 N.m. T or que Mower Blade Har d ware 1. Check to see that the blade and hardware are installed according to the diagram shown (A, Figures 8-10). 2. Torque the blade hardware to the noted torque (B): Note: Use a wooden block to prevent blade rotation.
8/2008 13 TP 300-5412---ZT-SN Axion / 150Z Series 8 0-90 ft. lbs. 10 8 -122 N.m. A B Figure 9. Torquing the mower blade hardware (42” Deck) 45-55 ft.
TP 300-5412---ZT-SN 8/2008 14 Axion / 150Z Series Size PSI bar Rear 10-12 ,69-, 8 3 Fr o n t 1 8 -20 1,24-1,3 8 Chec k Fluid Le vels Fill & Chec k Engine Oil Removing the rear cover to gain access to the engine, use the dipstick (Figure 11) to check the engine oil level.
8/2008 15 TP 300-5412---ZT-SN Axion / 150Z Series 42” Deck shown, all decks similar Figure 13. Lubrication (deck) Figure 14. Lubrication (ground speed control levers) Figure 15. Lubrication (chassis and wheels) Lubrication Lubricate the unit at the following lubrication points as well as those shown in Figures 13-15.
TP 300-5412---ZT-SN 8/2008 16 Axion / 150Z Series CHECK RIDER SAFETY SYSTEM Service Interval: Every 100 hours, every spring/fall, and after storage of 30 days or longer. This unit is equipped with safety interlock switches. These safety systems are present for your safety.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Snapper 7800392 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Snapper 7800392 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Snapper 7800392 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Snapper 7800392 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Snapper 7800392, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Snapper 7800392.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Snapper 7800392. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Snapper 7800392 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
