Manuale d’uso / di manutenzione del prodotto 421823BVE, 422023BVE del fabbricante Snapper
Vai alla pagina of 40
Safety Instructions & Operator’s Manual for REAR ENGINE RIDING MOWER SERIES 23 MODEL 421823BVE 422023BVE MODEL NUMBER EXPLANATION 42 18 23 B V E CUTTING WIDTH ENGINE OPTIONS ENGINE HP * ENGINE TYPE SERIES DESIGNATION ENGINE MODEL 42 - 42” Cutting Deck 18 - 18.
2 IMPORTANT SAFETY INSTRUCTIONS WARNING: This pow erful cutting machine is capable of am putating hands and feet and can throw objects that can cause injury and damage! Failure to comply w ith the following SAFETY instructions could result in serious injury or death to the operator or other persons.
3 IMPORTANT SAFETY INSTRUCTIONS PREPARATION (Continued From Previous Page) 6. Check the area to be mow ed and remove all objects such as toys, w ire, rocks, limbs and other objects that could cause injury if thrown by blade or interfere w ith mowing. 7.
4 IMPORTANT SAFETY INSTRUCTIONS TOWING 1. Tow only w ith a machine that has a hitch designed for tow ing. DO NOT attach towed equipment except at the hitch point. 2. Follow the manufacturer’s recommendation for w eight limits for tow ed equipment and towing on slopes.
5 TABLE OF CONTENTS IMPORTANT SAFETY INSTRUCTIO NS ........................................................................ 2-4 TABLE OF CO NTENTS ..................................................................................................... 5 SECTION 1 - FAMI LIARIZATI ON .
6 Section 1 - FAMILIARIZATION FIGURE 1.1 1.1 INTRODUCTION This manual has been prepared for the operator’s of the SNAPPER Rear Engine Rider. Its purpose, aside from recommending standard operating procedures and routine service requirements, is to promote SAFETY through the use of accepted operating practices.
7 Section 2 - OPERATING INSTRUCTIONS 2.1 PRE-START CHECK LIST Make the following checks and perform the service required before each start-up. 2.1.1. Check tires and add or release air as needed to bring pressure to 12 psi in front and 12 psi in rear tires.
8 Section 2 - OPERATING INSTRUCTIONS 2.3 STARTING & OPERATION 2.3.1. ENGINE (ELECTRIC START) IMPORTANT: When the ignition key is turned to “START”, the engine will turn over, but will not start unless the Clutch/Brake pedal is pressed all the way down, the Blade Lever is in the “Off” position (See Figure 2.
9 Section 2 - OPERATING INSTRUCTIONS 2.3 STARTING & OPERATION 2.3.1. ENGINE (ELECT RIC START) (Continued) 8. Should the battery be too weak to start the engine, Refer to Section “ENGINE (MANUAL START)” to manually start the electric start engines.
10 Section 2 - OPERATING INSTRUCTIONS WARNING Once blade is disengaged, it should come to a complete stop in 3 seconds or less. If the blade continues to rotate after 3 seconds, the blade brake must be adjusted. Refer to Section “BLADE BRAKE ADJUSTMENT” for adjustment procedures or return machine to an authorized SNAPPER dealer for adjustment.
11 Section 2 - OPERATING INSTRUCTIONS WARNING DO NOT leave machine w i th the engine running. Stop engine. Stop blade. Shift to neutral. Engage parking brake. Remove key . 2.4 STOPPING - ENGINE, WHEEL DRIVE, BLADE 2.4.1. ENGINE 1. Stop engine by turning key to the “OFF” position.
12 Section 2 - OPERATING INSTRUCTIONS 2.4 STOPPING - ENGINE, WHEEL DRIVE, BLADE 2.4.4. PARK BRAKE 1. Engage park brake by pushing clutch/brake pedal “DOWN” and moving the park brake latch over to the “ENGAGED” position. While holding the park brake latch “ENGAGED”, release clutch/brake pedal to set park brake.
13 Section 2 - OPERATING INSTRUCTIONS 2.6 REVERSE LOCKOUT MECHANISM Data indicates that tragi c back-over accidents occur each year. These accidents usually involve unsupervised children.
14 Section 3 - MAINTENANCE WARNING DO NOT attempt any adjustments, maintenance, service or repairs w ith the engine running. STOP engine. STOP blade. Engage parking brake. Remove key. Remove spark plug wire from spark plug and secure aw ay from plug. Engine and components are HOT.
15 Section 3 - MAINTENANCE WARNING DO NOT attempt any adjustments, maintenance, service or repairs w ith the engine running. STOP engine. STOP blade. Engage parking brake. Remove key. Remove spark plug wire from spark plug and secure aw ay from plug. Engine and components are HOT.
16 Section 3 – MAINTENANCE 3.2 SERVICE - AFTER FIRST 5 HOURS INTERLOCK SYSTEM SAFETY CHECKS (Cont.) ENGINE MUST NOT START IF: 1) Clutch/brake pedal is not fully depressed OR, 2) Blade Control is in the “ON” (blades engaged) position.
17 Section 3 – MAINTENANCE WARNING DO NOT attempt any adjustments, maintenance, service or repairs with the engine running. Stop engine. Stop blade. Engage parking brake. Remov e key. Remove spark plug wire from spark plug and secure aw ay from plug.
18 Section 3 – MAINTENANCE WARNING DO NOT attempt any adjustments, maintenance, service or repairs w ith the engine running. STOP engine. STOP blade. Engage parking brake. Remove key. Remove spark plug wire from spark plug and secure aw ay from plug.
19 Section 3 - MAINTENANCE WARNING DO NOT attempt any adjustments, maintenance, service or repairs w ith the engine running. STOP engine. STOP blade. Engage parking brake. Remove key. Remove spark plug wire from spark plug and secure aw ay from plug. Engine and components are HOT.
20 Section 3 - MAINTENANCE 3.6 STORAGE (OUT OF SEASON) If desired, the Rear Engine Rider can be stored on the rear bumper. Perform the following procedures to insure the Rear Engine Rider will operate properly when taken out of storage. 3.6.1. Thoroughly clean the Rear Engine Rider by removing all grass clippings and debris.
21 Section 4 - ADJUSTMENTS & REPAIR WARNING DO NOT attempt any adjustments, maintenance, service or repairs w ith the engine running. STOP engine. STOP blade. Engage parking brake. Remove key . Remove spark plug w ire from spark plug and secure aw ay from plug.
22 Section 4 - ADJUSTMENTS & REPAIR WARNING DO NOT attempt any adjustments, maintenance, service or repairs w ith the engine running. STOP engine. STOP blade. Engage parking brake. Remove key. Remove spark plug wire from spark plug and secure aw ay from plug.
23 Section 4 - ADJUSTMENTS & REPAIR WARNING DO NOT attempt any adjustments, maintenance, service or repairs w ith the engine running. STOP engine. STOP blade. Engage parking brake. Remove key. Remove spark plug wire from spark plug and secure aw ay from plug.
24 Section 4 - ADJUSTMENTS & REPAIR WARNING DO NOT attempt any adjustments, maintenance, service or repairs w ith the engine running. STOP engine. STOP blade. Engage parking brake. Remove key. Remove spark plug wire from spark plug and secure aw ay from plug.
25 Section 4 - ADJUSTMENTS & REPAIR WARNING DO NOT attempt any adjustments, maintenance, service or repairs w ith the engine running. STOP engine. STOP blade. Engage parking brake. Remove key. Remove spark plug wire from spark plug and secure aw ay from plug.
26 Section 4 - ADJUSTMENTS & REPAIR WARNING DO NOT attempt any adjustments, maintenance, service or repairs w ith the engine running. STOP engine. STOP blade. Engage parking brake. Remove key. Remove spark plug wire from spark plug and secure aw ay from plug.
27 Section 4 - ADJUSTMENTS & REPAIR WARNING DO NOT attempt any adjustments, maintenance, service or repairs w ith the engine running. STOP engine. STOP blade. Engage parking brake. Remove key. Remove spark plug wire from spark plug and secure aw ay from plug.
28 Section 4 - ADJUSTMENTS & REPAIR WARNING DO NOT attempt any adjustments, maintenance, service or repairs with the engine running. Stop engine. Stop blade. Engage parking brake. Remov e key. Remove spark plug wire from spark plug and secure aw ay from plug.
29 Section 4 - ADJUSTMENTS & REPAIR WARNING The electrolyte (acid) produces a highly explosive gas. Keep all sparks, flame and fire aw ay from area when charging battery or when handling electrolyte or battery. Electroly te (acid) is a highly corrosive liquid.
30 Section 4 - ADJUSTMENTS & REPAIR 4.6.6. BATTERY TESTING Batter y Condition Chart State of Charge Syringe Hy drometer Di gital Voltmeter Five Ball Hy drometer 100% Charged w/ Sulfate Stop 1. 280 12.80v Five Balls Floating 100% Charged 1.265 12.60v Four Balls Floating 75% Charged 1.
31 TROUBLESHOOTING PROBLEM PROBABLE CAUSE CORRECTIVE ACTION Engine Will Not 1. Fu el ta nk em pty . 1. Fill fuel tank with fresh fuel to proper level. Start Using 2. Engine needs choking. 2. Move choke control to “CHOKE” position. Recoil Starter 3.
32 TROUBLESHOOTING PROBLEM PROBABLE CAUSE CORRECTIVE ACTION Rider Will Not Move 1. Drive disc worn or dama g ed. 1. Re p lace drive disc. Loss Of Traction 2. Rubber drive disc is not tracking properly on drive disc. 2. Adjust rubber drive disc. 3. Tapered axle bolt and nut missing.
33 MAINTENANCE SCHEDULE SUBJECT SERVICE TO BE PERFORMED REFERENCE PAGES EACH USE 5 HOURS 25 HOURS 50 HOURS 100 HOURS EACH SEA SON Engine Check Oil Level Page 7 X Tires Check Pressures Page 7 X Engine .
34 2 YEAR LIMITED WARRANTY For two (2) years from purchase date for the orig inal purchaser's residential, non-commercial use, SNAPPER , through any authorized SNAPPER dealer will replace, free o.
35 PRIMARY MAINTENANCE.
36 PRIMARY MAINTENANCE.
37 PRIMARY MAINTENANCE.
38 PRIMARY MAINTENANCE.
39 SNAPPER PRODUCT REGISTRATION FORM IMPORTANT: KEEP THIS INFORMATION FOR YOUR PERSONAL RECORDS (Complete the following informa tion on your Snapper purchase) Model Number ____________________________.
40 Safety Instructions & Operator’s Manual for REAR ENGINE RIDING MOWER SERIES 23 IMPORTANT Snapper products are built using engines that meet or exceed all applicable emissions requirements on the date manufactured. The labels on those engines contai n very important emissions information and critical safety warnings.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Snapper 421823BVE, 422023BVE è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Snapper 421823BVE, 422023BVE - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Snapper 421823BVE, 422023BVE imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Snapper 421823BVE, 422023BVE ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Snapper 421823BVE, 422023BVE, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Snapper 421823BVE, 422023BVE.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Snapper 421823BVE, 422023BVE. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Snapper 421823BVE, 422023BVE insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
