Manuale d’uso / di manutenzione del prodotto 1691998 del fabbricante Snapper
Vai alla pagina of 19
OPERATOR’S MANUAL 42”/48” Turbo Blower Assembly Mfg. No: 1691810 Mfg. No. 1691998 FORM 170460604 PRINTED IN U.S.A. 12/93-3ooccI.
HEX CAPSCREW PLAIN WASHER LOCKWASHER a p. NUT HEX CAPSCREW IDENTIFICATION Shown below are actual size hex heads for standard screw sizes. Example: a l/4” screw has a 7116 head and.
Table of Contents Safety Decal ................................ Safety Rules ................................ Installation Lawn Tractor ........................... Front-Cut Rider ......................... Operation .................................. Standard Fastener Identification Chart .
Safety Rules A Read these safety rulesand the safety rules in yo,ur Operator’s Manual and follow them closely. Failure to obey these rules could result in loss of control of vehicle, severe personal injury to yourself, or damage to property or equipment.
installation - Lawn ,Tractors NOTE Two spacers are packaged with turbo biower. Installation on tractor requires use of 4-l/16” spacer (see step 11); the 1/2”spacerwill not be used. 1. Remove mower deflector and arbor cover as follows: a. Remove the mower deflector by removing two carriage bolts, lockwashers and nuts.
NOTE Front belt stop should be installed facing outside of deck. ‘6. Install thefront belt stop (A, figure4) onto5/16- 18 x l-1/2 capscrew (installed in step 3) as shown. If removed, reinstall brake spring or spring anchor (F) before flange nut(G). Tighten nut (E) snug only - belt stop will be adjusted in step 8.
10. The baffle (A, figure 7) is installed in the blower housing for use with 42” mower. For use with 48” mower, remove the baffleand install in holes marked 48”. I Figure 7. A Battle NOTE On42”and 48” mowersthecapscrewinstalled in next step is used in the hole occupied by a screw held in place by a retaining nut.
12. Install wing nut (D, figure 9) as follows: a. Remove existing hardware from front end of stone guard. b. From inside deck, install new 5/16-18 x 2-l/4 carriage bolt (F, figure 9). Then install the cup (A), 5/16 lockwasher (6). and 506 nut (C). Tighten the nut.
c. Place mower in low cut position. Raise the flap (A, figure 12) and push on the belt retainer (E) to obtain slack in the belt. Install the blower drive belt (D) in the top groove of the pulley(B). d. Rotate the pivoting cover (A, figure 13) into place and attach the hook (B) to the clip (C) on the housing.
Installation - Front Cut Riders NOTES 1. Two spacers are packaged with the turbo blower. Installation on the Front-Cut Rider requires use of the l/2” spacer (see step 14).
6. Remove the capscrew, lockwasher, and flat washer securing right hand arbor pulley. Retain the washers for reinstallation (step 9). Use a wood block to prevent blade from turning. SunRunnerNanguard Models 6. On early models without bet stop (A, figure 3) remove two self-tapping screws from arbor and install two .
9. Slip the mower drive belt (A, figure 5) around the bottom groove of double-groove pulley (B). Install pulley with hub down and secure with new 7/l 6-14 x 2-l /4” capscrew (C) and washers (D and E) removed in step 5. Make sure splines arecorrectlyalignedand torquecapscrewto55- 60 ft.
13. Install the new baffle (A, figure 8) in deck on stone guard using existing hardware. Hardware may be installed with nut to inside or nut to outside. 14. On new arbor cover, install on top of weld bolt (A, figure 9) the largest washer (B l-i/Z” O.
16. Make sure that flat washer (F, figure 9) is on top of spacer assembly and install new arbor belt cover (A, figure 10) as shown in figure 10. Secure with flat washer (l-1/4” O.D.) and locknut (8). Belt cover should be free to pivot. 17. Install the blower assembly as follows: a.
Operation A WARNING For safety reasons, grass and debris should not be removed from any part of turbo or collection system until engine is shut off, key removed, and all moving parts have stopped. I A I WARNING Before raising cart or twin-bag cover, shut off engine, remove key, and set parking brake.
.
i.
.:::).‘,:,:::: ~._,, ,.
..:,, ::: TORQUE SPECIFICATIONS FOR STANDARD MACHINE HARDWARE TOLERANCE +200/o SIZE 8-32 8-36 lo-24 lo-32 l/4-20 l/4-28 5116-18 5116-24 318-16 318-24 7116-14 7116-20 l/2-13 112-20 9116-12 9116-18 518-11 518-18 314-10 3/4-16 718-g 718-14 1-8 1-12 SAE GRADE #2 SAE GRADE A15 SAE GRADE #8 0 Q 8.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Snapper 1691998 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Snapper 1691998 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Snapper 1691998 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Snapper 1691998 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Snapper 1691998, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Snapper 1691998.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Snapper 1691998. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Snapper 1691998 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
