Manuale d’uso / di manutenzione del prodotto SA-001S del fabbricante SkyLink
Vai alla pagina of 20
Model: SA-001S User’ s Instructions W ireless External Alarm.
1 TABLE OF cONTENT INTRODUCTION ................................................................................................... INSTALLATION .............................................................................................. PROGRAMMING – LEARN REMOTE OR SENSORS OR CONTROL PANEL .
2 INTrOducTION Congratulations on purchasing the Skylink Wireless External Alarm SA-001 Series. The SA-001 Series provide you with a piercing siren and powerful features yet ease to use. You will nd the installation to be simple and be able to get the unit up and running easily.
3 - Set Compatibility Jumper: Refer to the following table to setup the Wireless External Alarm to work with different Skylink’s Security System or Sensors. To select, you will see a jumper connector marked “J2” as shown below. Use a paper clip to remove the jumper connector and re-locate to the proper posts.
4 cAuTION: The adaptor as a disconnect devices: − the socket-outlet shall be installed near the equipment and shall be easily accessible. In order for the remote or sensor or control panel to communicate with the Exter- nal Wireless Alarm properly, this need be programmed into the Wireless External Alarm previously.
5 3B – Learn motion sensor to the Wireless External Alarm: - Press and hold the Learn button on the Wireless External Alarm for 2 seconds and then release. The Learn/Set LED will ash. - Activate the motion sensor by pressing the “Test/Set” button on the motion sensor.
6 Mute button 3C – Learn door/window sensor to the Wireless External Alarm: - Press and hold the Learn button on the Wireless External Alarm for 2 seconds and then release. The Learn/Set LED will ash. - Activate the Door/Window Sensor, by separating the magnets to send the signal.
7 To erase unwanted remote(s) or sensor(s) or control panel(s) from the Wireless External Alarm will erase all learned devices from the Wireless External Alarm. - Press and hold the Learn/Set button on the Wireless External Alarm for 8 seconds. - While holding the Learn/Set button on the Wireless External Alarm until the Learn/Set LEDs turn on.
8 The Wireless External Alarm can be programmed to react 2 arming sequences when it receives the signal from the sensor. In order to arm the Wireless External Alarm, the remote (optional) must be programmed to the Wireless External Alarm.
9 - You will hear 1 beep and the LEDs will ash once indicating the Wireless External Alarm is being counted to Away mode. - After 30 seconds, you will hear 2 beeps and the LEDs will ash twice indicating the Wireless External Alarm in Away mode.
10 The Wireless External Alarm is designed to work with the Skylink security control panel such as AM-001, ML-001 and SC-001. Put the control panel that you plan to program into programming mode. Refer to the User’s Instructions of that control panel.
11 You may connect your existing alarm system with the Wireless External Alarm so that the Wireless External Alarm will be triggered by your alarm system.
12 You can enable or disable the Alert Notication. When it is set to enable, the Wireless External Alarm will beep when arm or disarm or during the entry/exit countdown period. When it is set to disable, the Wireless External Alarm will not beep when arm or disarm or during the entry/exit countdown period.
13 When the battery power is being reduced, the Wireless External Alarm will emit 3 beeps when the remote arm or disarm the unit. It is time to replace the batteries or recharge the battery pack (rechargeable battery only) as soon as the low battery signal appears.
14 Your Wireless External Alarm requires few simple maintenance to ensure its con - tinued reliability and operation. - The solar panel on the top housing should be cleaned using the soft and damp cloth. This will ensure the solar panel receives all the available light.
15 Questions Solutions Why the Wireless External Alarm does not respond to the sensors or remote? You must program the sensors or remote to the Wireless External Alarm before they can work together. Why I can’t arm my system? Make sure none of the sensors are trig- gered.
16 Fcc This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
17 WArrANTy If, within one year from date of purchase, this product should become defective (except battery), due to faulty workmanship or materials, it will be repaired or replaced, without charge. Proof of purchase and a Return Authorization Number are required.
18 cusTOmEr sErVIcE If you would like to - nd out the up-to-date specications - know more about features and applications - download documents, i.e. user’s instructions - order Skylink products or if you have difculty getting the products to work, please: 1.
19 101Y035 DEC,2012.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il SkyLink SA-001S è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del SkyLink SA-001S - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso SkyLink SA-001S imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul SkyLink SA-001S ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il SkyLink SA-001S, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del SkyLink SA-001S.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il SkyLink SA-001S. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo SkyLink SA-001S insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
