Manuale d’uso / di manutenzione del prodotto STP-1000T del fabbricante Sima Products
Vai alla pagina of 15
Smooth Start Series User Instructions for Model STP-1000T Power Inverter Model STP-1000T.
Safety Information IMPORTANT Read all the Cautions and Warnings before installing and using the power inverter. The inverter must be properly installed. IMPORTANT If you are not familiar with 12 volt high current wiring, it is recommended that you have a professional automotive installer install the inverter.
Table of Contents Safety Information ...................................................................................................2 Introduction ....................................................................................................
Introduction Congratulations on your purchase of a Sima Products Corporation power inverter. It provides 115 VAC anywhere you have 12 DC volts in your car, truck, RV or boat. It is designed to be easy to use and provide years of dependable service. Key Features High-efficiency operation to provide the mo st output with the least battery power.
Overview of the Power Inverter The STP-1000T power inverters are electronic devi ces that convert the low voltage 12 VOLTS DC from a battery or other power source to 115 VAC to run standard household appliances. See the section on How it Works to learn more about the technology used in these power inverters.
Inst allation Installation Overview There are three basic steps you need to follow when installing the power inverter. 1) Mounting: Mount the inverter securely 2) Wiring: Wire the inverter to a 12 VOL.
Step #2: Wiring Inverter to 12 volt Power The power inverter requires connection to a standa rd 12 volt DC power source as found in most cars, trucks, RVs and boats. The power source must provide between 11 and 15 volts DC. The power source must be able to provide sufficient current to power the load.
Permanent Installation Figure 3, Wiring the STP-1000T power inverter Caution: Always use adequate wire siz e and fusing for any installation Wiring Steps • Disconnect the positive battery terminal before doing any wiring to the inverter.
• Double check all wiring for proper polarity. • Install the fuse and reconnect the wire to the battery. Note, a slight spark and beep from the inverter is normal when the unit is first connected to 12 volt power.
inverter to shut down or the fuse to blow. Repeat ed use of excessive power draw can cause failure of the power inverter. How to calculate power usage . Most products have a power rating on them such as 45 watts. Others may be marked with their current draw, such as .
Battery Life Chart Power Usage Approximate 12 volt Current Typical operation time with 50 amp-hour car battery Typical operation time with 100 amp- hour car battery 100 watt 9 Amps 5.
How the Inverter W orks The Sima Products Corporation power inverter has two electronic sections. The first section converts 12 volts DC to approximately 160 volts DC using modern high frequency conversion techniques that uses small lightweight efficient transformers.
T roubleshooting Problem Cause Solution Unit does not operate Input voltage is below 10 volts Attach to proper supply Fuse blown Determine cause for fuse blowing and then replace fuse feeding inverter. Unit operates for a short period and then turns off Load is trying to draw too much current Be sure load is less than rated watts of inverter.
Product S pecifications Key Features STP-1000T Input 12 - 15 volts DC Input no-load current < .6 A Output type modified sine wave Output, Watts, 10 minutes continuous 1,000W 800W Output, peak 2,000W Frequency, +/- 1% 60 Hz Efficiency 85 - 90% Outlets 2 Protection Thermal Low battery alarm (10.
Limited W arranty Sima Products Corporation (“Company”) warrants that if the accom panying product proves to be defective to the original purchaser in material or workm anship within 90 days from .
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Sima Products STP-1000T è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Sima Products STP-1000T - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Sima Products STP-1000T imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Sima Products STP-1000T ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Sima Products STP-1000T, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Sima Products STP-1000T.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Sima Products STP-1000T. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Sima Products STP-1000T insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
