Manuale d’uso / di manutenzione del prodotto A1001 del fabbricante Axis Communications
Vai alla pagina of 63
AXIS A1 00 1 Network Door Controller & AXIS Entry Manager User Manual.
About this Document This manual is intended for administrators and users of AXIS A1 001 Network Door Controller and is applicable to AXIS Entry Manager and rmware 1.25 and later . It includes instructions for using and managing the product on your network.
the product shall be grounded either through a shielded network cable (STP) or other appropriate method. The power supply used with this product shall fulll the requirements for Safety Extra Low V oltage (SEL V) and Limited P ower Source (LPS) according to IEC/EN/UL 60950-1.
AXIS A1001 Network Door Controller & AXIS Entry Manager T able of Contents Hardware Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 LED Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . .
AXIS A1001 Network Door Controller & AXIS Entry Manager Hardware Overview Hardware Overview The hardware overview is divided into the following categories: • Front and back. See page 5 . • I/O interface. See page 6 . • External power inputs.
AXIS A1001 Network Door Controller & AXIS Entry Manager Hardware Overview 1 2 3 4 5 6 7 8 9 10 1 1 1 2 I/O interface: 1 Reader data connector (READER DAT A 1) 1 0 Reader data connector (READER DAT.
AXIS A1001 Network Door Controller & AXIS Entry Manager Hardware Overview 1 2 3 4 5 6 7 8 9 10 1 1 1 2 1 3 LED indicators, buttons and other hardware: 1 P ower LED indicator 2 Status LED indicator.
AXIS A1001 Network Door Controller & AXIS Entry Manager Hardware Overview Green Steady when not energized. Red Steady when energized. Lock Unlit Floating. Note • The Status LED can be congured to ash while an event is active. • The Status LED can be congured to ash for identifying the unit.
AXIS A1001 Network Door Controller & AXIS Entry Manager Hardware Overview P ower Outputs P ower Lock Connector 4-pin terminal block for connecting one or two locks. The lock connector can also be used to power external devices. For specications, see page 60 .
AXIS A1001 Network Door Controller & AXIS Entry Manager Access the Product Access the Product To install the Axis product, refer to the Installation Guide supplied with the product. The product can be used with most operating systems and browsers.
AXIS A1001 Network Door Controller & AXIS Entry Manager Access the Product The Overview P age The Overview page in AXIS Entry Manager shows information about the door controller’s name, MAC address, IP address, and rmware version. It also enables you to identify the door controller on the network or in the system.
AXIS A1001 Network Door Controller & AXIS Entry Manager System Configuration System Configuration To open the product’s Setup pages, click Setup in the top right-hand corner of the Overview page. The Axis product can be congured by administrators.
AXIS A1001 Network Door Controller & AXIS Entry Manager System Configuration Note • When you switch languages, the date format also changes to a format commonly used in the selected language. The correct format is displayed in the data elds.
AXIS A1001 Network Door Controller & AXIS Entry Manager System Configuration Create a New Hardware Conguration To create a new hardware conguration from the beginning: 1. Go to Setup > Hardware Conguration and click Start new hardware conguration .
AXIS A1001 Network Door Controller & AXIS Entry Manager System Configuration - Open circuit = Open door – Select if the door monitor circuit is normally closed. The door monitor gives the door open signal when the circuit is open. The door monitor gives the door closed signal when the circuit is closed.
AXIS A1001 Network Door Controller & AXIS Entry Manager System Configuration - Open circuit = Locked – Select if the lock monitor circuit is normally closed. The lock monitor gives the door unlocked signal when the circuit is closed. The lock monitor gives the door locked signal when the circuit is open.
AXIS A1001 Network Door Controller & AXIS Entry Manager System Configuration 1. Install end of line resistors on all the used inputs. See the connection diagram on page 62 . 2. Go to Setup > Hardware Reconguration and select Enable supervised inputs .
AXIS A1001 Network Door Controller & AXIS Entry Manager System Configuration • Set the date and time manually . See page 18 . • Get the date and time from the computer . See page 18 . Current controller time displays the door controller’s current date and time (24h clock).
AXIS A1001 Network Door Controller & AXIS Entry Manager System Configuration Basic T CP/IP Settings The Axis product supports IP version 4 (IPv4). The Axis product can get an IPv4 address in the following ways: • Dynamic IP address – Obtain IP address via DHCP is selected by default.
AXIS A1001 Network Door Controller & AXIS Entry Manager System Configuration Important • All changes to card formats apply to the whole system of door controllers. • Y ou can only enable and disable card formats if at least one door controller in the system has been congured with at least one reader .
AXIS A1001 Network Door Controller & AXIS Entry Manager System Configuration - BinBE2Hex – Binary data is encoded as hex-lowercase numbers in big endian byte order . The hexadecimal system, also known as the base-16 number system, consists of 16 unique symbols: the numbers 0–9 and the letters a–f.
AXIS A1001 Network Door Controller & AXIS Entry Manager System Configuration • Name – The user-dened name of the door controller . If the administrator has not set a name when conguring the hardware, the default name will be shown.
AXIS A1001 Network Door Controller & AXIS Entry Manager System Configuration 3. After the hardware conguration has been reset, go to Setup > Manage Network Door Controllers in System . 4. In the Network door controllers in system list, identify the door controller that you want to remove and click Remove from system .
AXIS A1001 Network Door Controller & AXIS Entry Manager Access Management Access Management About Users In AXIS Entry Manager , users are people who have been registered as owners of one or more tokens (identication types). Each person must have a unique user prole to be granted access to doors in the access control system.
AXIS A1001 Network Door Controller & AXIS Entry Manager Access Management 8. Add users to groups. For applied examples of this workow , see Example Access Schedule Combinations on page 3 1 . Create and Edit Access Schedules Access schedules are used to dene general rules for when doors can and cannot be accessed.
AXIS A1001 Network Door Controller & AXIS Entry Manager Access Management cannot override that identication type schedule. However , if a group schedule is more restrictive about access than the identication type schedule, the group schedule overrides the identication type schedule.
AXIS A1001 Network Door Controller & AXIS Entry Manager Access Management Create and Edit Groups Groups allow you to manage users and their access rights collectively and efciently . A group consists of credentials that tell the system which users the group consists of and when and how the group members are granted access to the doors.
AXIS A1001 Network Door Controller & AXIS Entry Manager Access Management If both identication types Card number only and PIN only are added, users can choose to either swipe their card or enter their pin to access the door .
AXIS A1001 Network Door Controller & AXIS Entry Manager Access Management 4. Select the Unlock state ( unlocked or unlock both locks depending on whether the door has one or two locks). 5. Click OK . 6. Apply the predened Ofce hours access schedule to the Scheduled unlock state.
AXIS A1001 Network Door Controller & AXIS Entry Manager Access Management 4. Click Save . 5. Drag the user to one or more groups in the Groups list. If the Groups list is empty , create a new group. See Create and Edit Groups on page 27 . To expand an item in the Users list and view a user’s credentials, click .
AXIS A1001 Network Door Controller & AXIS Entry Manager Access Management 1. Go to Setup > Import Users . 2. Locate and select the *.csv or *.txt le that holds the list of users. 3. Select the correct credential option for each column. 4. To import the users to the system, click Import users .
AXIS A1001 Network Door Controller & AXIS Entry Manager Access Management 2. Create a day shift hours Schedule item that recurs Monday–Friday , 06:00–16:00. 3. Create two groups, one Group called Guards and one Group called Day shift personnel .
AXIS A1001 Network Door Controller & AXIS Entry Manager Alar m and Event Configuration Alar m and Event Configuration Events that occur in the system, for example when a user swipes a card or a REX device is activated, are logged in the event log.
AXIS A1001 Network Door Controller & AXIS Entry Manager Alar m and Event Configuration Important Each time that you enable or disable global events, the event log is cleared. This means that all events before that moment are removed and the event log starts over .
AXIS A1001 Network Door Controller & AXIS Entry Manager Alar m and Event Configuration 6. Under Actions , select Send Notication from the Type drop-down list. 7. Select an email recipient from the drop-down list. See Add Recipients on page 37 .
AXIS A1001 Network Door Controller & AXIS Entry Manager Alar m and Event Configuration - Area Removed – Not supported by this version of AXIS Entry Manager .
AXIS A1001 Network Door Controller & AXIS Entry Manager Alar m and Event Configuration - Network – Triggers the action rule when the network connection is lost. Select Y es to trigger the action rule when the network connection is lost. Select No to trigger the action rule when the network connection is restored.
AXIS A1001 Network Door Controller & AXIS Entry Manager Alar m and Event Configuration 1. Go to Setup > Additional Controller Conguration > Events > Recipients and click Add . 2. Enter a descriptive name. 3. Select a recipient T ype .
AXIS A1001 Network Door Controller & AXIS Entry Manager Alar m and Event Configuration 2. Enter a descriptive name and the information needed for a daily , weekly , monthly or yearly schedule. 3. Click OK . To use the schedule in an action rule, select the schedule from the Schedule drop-down list in the Action Rule Setup page.
AXIS A1001 Network Door Controller & AXIS Entry Manager Reports Reports The Reports page allows you to view , print, and export reports that contain different types of information about the system. For more information about which reports that are available, see Report Types on page 40 .
AXIS A1001 Network Door Controller & AXIS Entry Manager System Options System Options Security Users User access control is enabled by default and can be congured under Setup > Additional Controller Conguration > System Options > Security > Users .
AXIS A1001 Network Door Controller & AXIS Entry Manager System Options To access the Axis product via the desired protocol, enter https:// or http:// in the address eld in a browser . The HTTPS port can be changed on the System Options > Network > T CP/IP > Advanced page.
AXIS A1001 Network Door Controller & AXIS Entry Manager System Options 1. Create a self-signed certicate as described above. 2. Go to Setup > Additional Controller Conguration > System Options > Security > Certicates . 3. Click Create certicate signing request and provide the requested information.
AXIS A1001 Network Door Controller & AXIS Entry Manager System Options If DHCP is enabled and the product cannot be accessed, run AXIS IP Utility to search the network for connected Axis products, or reset the product to the factory default settings and then perform the installation again.
AXIS A1001 Network Door Controller & AXIS Entry Manager System Options AXIS Video Hosting System (A VHS) AVHS used in conjunction with an AVHS service, provides easy and secure Internet access to controller management and logs accessible from any location.
AXIS A1001 Network Door Controller & AXIS Entry Manager System Options Host Name Conguration The Axis product can be accessed using a host name instead of an IP address.
AXIS A1001 Network Door Controller & AXIS Entry Manager System Options Alternative HTTP port - Select this option to manually dene an external HTTP port. Enter a port in the range 1 024–65535. If the port eld is empty or contains the default setting, which is 0, a port number is automatically selected when enabling NA T traversal.
AXIS A1001 Network Door Controller & AXIS Entry Manager System Options The following traps are available: • Cold start • Warm start • Link up • Authentication failed SNMP v3 provides encryption and secure passwords. T o use traps with SNMP v3, an SNMP v3 management application is required.
AXIS A1001 Network Door Controller & AXIS Entry Manager System Options Click Restore to reset most settings to the factory default values. The following settings are not affected: • the boot protocol (DHCP or static) • the static IP address • the default router • the subnet mask • the system time • the IEEE 802.
AXIS A1001 Network Door Controller & AXIS Entry Manager System Options Advanced Scripting Scripting allows experienced users to customize and use their own scripts. NO NO NO TICE TICE TICE Improper use may cause unexpected behavior and loss of contact with the Axis product.
AXIS A1001 Network Door Controller & AXIS Entry Manager Troubleshooting Troubleshooting Check the Firmware Firmware is software that determines the functionality of network devices. One of your rst actions when troubleshooting a problem should be to check the current rmware version.
AXIS A1001 Network Door Controller & AXIS Entry Manager Troubleshooting 3. Open a browser and type in the product’s IP address. In the page that opens, use the Browse button to select the upgrade le to use. Then click Load to restart the upgrade process.
AXIS A1001 Network Door Controller & AXIS Entry Manager Troubleshooting Status and Network indicator LEDs are ashing red rapidly Hardware failure Contact your Axis reseller .
AXIS A1001 Network Door Controller & AXIS Entry Manager T echnical Specifications T echnical Specifications AXIS A1 00 1 Network Door Controller Function/group Item Specications Models AXIS A.
AXIS A1001 Network Door Controller & AXIS Entry Manager T echnical Specifications Function/group Item Specications Casing Plastic Software Conguration and basic access control management th.
AXIS A1001 Network Door Controller & AXIS Entry Manager T echnical Specifications AXIS Entry Manager Function/group Item Specications Models AXIS A1 00 1 with built-in web-based software Reade.
AXIS A1001 Network Door Controller & AXIS Entry Manager T echnical Specifications Function/group Item Specications Casing Plastic Software Conguration and basic access control management th.
AXIS A1001 Network Door Controller & AXIS Entry Manager T echnical Specifications Reader Data Connector 6-pin terminal block supporting RS485 and Wiegand protocols for communication with the reader .
AXIS A1001 Network Door Controller & AXIS Entry Manager T echnical Specifications Door Connector Two 4-pin terminal blocks for door monitoring devices (digital input). All door input pins can be supervised. If the connection is interrupted, an alarm is triggered.
AXIS A1001 Network Door Controller & AXIS Entry Manager T echnical Specifications Network Connector RJ45 Ethernet connector . Supports P ower over Ethernet (P oE). Use Category 5e cables or higher . Function Specications P ower and Ethernet P ower over Ethernet IEEE 802.
AXIS A1001 Network Door Controller & AXIS Entry Manager T echnical Specifications Function Pin Notes Back tampering alarm 1–2 Front tampering alarm 1–2 To bypass the front and back tampering alarm simultaneously , connect jumpers between TB 1, TB 2 and TF 1, TF 2 respectively .
AXIS A1001 Network Door Controller & AXIS Entry Manager T echnical Specifications Supervised Inputs i 22k Ω 4. 7 k Ω i i To use supervised inputs, install end of line resistors. This applies to all supervised inputs. For information about limitations and updates, see the product’s release notes.
User Manual V er . M5.7 AXIS A1 00 1 Network Door Controller & AXIS Entry Manager Date: November 20 14 © Axis Communications AB, 20 13 - 20 14 P art No.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Axis Communications A1001 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Axis Communications A1001 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Axis Communications A1001 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Axis Communications A1001 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Axis Communications A1001, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Axis Communications A1001.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Axis Communications A1001. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Axis Communications A1001 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
