Manuale d’uso / di manutenzione del prodotto IZS30 SERIES del fabbricante Sierra Monitor Corporation
Vai alla pagina of 26
DOCUMENT No. : IZ*-OMJ0003 OPERA TION MANUAL PRODUCT NAME : Ionizer MODEL: IZS30 Series ○ Read this operation manual carefully to understand before inst allation and operation. ○ Pay extra attention on the clause concerning the safety. ○ Keep this operation manua l available whenever necessary .
Content s 1. Safety instructio ns......................................................................................................... 2 2. How to order...........................................................................................
1. Safety instructions These safety instructions are intended to prevent haz ardous situations and/or equ ipment da mage. These instruct ions indicat e the lev el of potent ial hazard by labeling "Caution" , " W arni ng" , and "Danger" .
WARNING 1. This produ ct is made for general in d ustry. Con tact SMC before use, if you are planning to use for other purposes. 2. Use under sp ecified voltage and te mperature. Voltage out o f speci f ication may ca use m alfunctio n, breakage, electric sh o ck and f i re.
W ARNING 1. Check that power sup ply capacity is enough and voltage is i n specif ication before piping. 2. Apply type D earthing t o prevent electrical shoc k in accorda nce with instr uctions on this operatio n manual. 3. Be sure to cut off pow er supply a t wiring (i nclu/din g connector plug-in/out) .
product. k. The place wher e strong high frequency is generated. l. The place w here lightning disaster is ex pected. m. The place w here the product is direct ly exposed to the v i bration and i mpact. n. The situatio n where t he force a nd weight t h at causes deformat ion of the pro duct is applie d .
2. How to or der I Z S 3 0 – 7 8 0 S B I Z S 3 0 - D 1 I Z S 3 0 - C S I Z S 3 0 - B E I Z S 3 0 - N T Bracket B Mounted ∗ Not mounted Product na me I Z S 3 0 Bar t ype Ionizer Bar length 300 300 .
3. Specifi cations 3-1. Ionizer [Note] *1: At distance 30 0mm bet ween Ioniz e r and charge d object, w i th purge air. *2: The sm allest flow rate for elimin ation at di stance 200 mm betwe en Ionizer and c harged object.
4. Installat ion 4-1. Install ation of Io nizer body Investigate t he places w h ere static pro bl em occurs, or process and part s whic h generate E SD (Electro stat ic discharge), a nd carefu lly consider the requir ed conditions to ens u re appropr iate static charge el imination before instal l ation.
4. Adjust ang l e of the io nizer body to ensure proper stat i c charge el imination, and f i x it with d etent threads (M5) o f bracket s. Recommende d tightenin g torque for d etent thr ead: 1.
3. Peal off the seal attach ed on the dete cting hole of the sur f ace elect ric potential s ensor. 4. D irect the sur f ace electric pot ential sensor to the target’s stati c cha rge as ad j usting the an gl e, and fix the detent t hread (M5) of bracket.
2. Arrange lead wires in accordance w i th the w iring table. The unused w i res s hould be cut short or covered with vinyl tape w i thout pealing the co at to prevent them fr om coming c o ntact w ith other wires. See [4-4. Conn ection circuit ]. W iring table for power sup pl y cable IZS30-CP Note No.
2. Arrange lead wires in accordance w i th the w iring table. The unused w i res s hould be cut short or covered with vinyl tape w i thout pealing the co at to prevent them fr om coming c o ntact w ith other wires. See [4-4. Conn ection circuit ]. W iring table for power sup pl y cable IZS30-CP Note No.
4. Insert the modular p lug on the other side of sensor cab le IZS3 0-CS into the modular jack of the electric pote ntial sensor. I f the modular plug is properly in serted and locke d, a lever clicks to notify it’ s loc ked.
4-4. Connecti on circuit Ionizer POWER conn ector [Note 1] indicates the coating col or for lead wire of dedicated cab le [Note 2] Connect [4. Stop si gnal of static charge elimin a tion] to GND when starting the ionizer operation. When the ter mi nal is open , the operation will stop.
5. Function d escripti on 5-1. Operatio n mode Three operat i on modes ar e available in IZS30. Us e t hese modes d ep end ing on applicatio ns and operating cond i tions.
5-2. Output sig nal Signal t ype Function Signal for s tati c charge elimination com pletion (When s urface electric potential sens or is used) Output when s tatic charg e elimination is com pleted, or no target’s static charge exists. Abnorm al high voltage Output when an y discharge prob e gets short ed wi th other discharge probes or housi ng.
6. Selectio n and settin g of equi pment 6-1. Sensin g DC mode 1. selection o f bar lengt h Select the length applicable to work size base on [ 2. static charge eliminati on area of 7-1.
7. Technical d ata 7-1. Static ch arge elimi nation c h aracterist ics (ref e rence 1. Installat ion distance and static charge el imination time .
2. S tatic charge eliminati on area Ionizer depth d i rection Ionizer wid th directi on T arget’s work of stat ic charge Charged plate dimensions: 150×150mm Capacity:20 F Meas.
Ionizer depth d i rection ( with air purg e) Ionizer wid th directi on wit h air purge Ionizer height direction -Installed position of target’ s static charge mm T arget’s work of static charge Charged plate dimensions: 150×150mm Capacity:20 F Meas.
Charged am ount and st atic charge elimi n ation ti me Operating f requency and stat ic charge eli mination time (W/O surface e lectric potential sen so r) .
7-2. Outli ne dimensio ns 1. Ionizer (I Z S30-**) .
End brack et (IZS30-B E) Intermediate b rack et IZS30-BM Thread for mounting M5 (Should be prepared by user) Angle ajustment av ailable (± 90° ) Thread for mounting M.
Surface ele ctric potent ial sensor (IZS30-D 1 ) Sensor bra ck et (IZS 30-BS) Detecting hope 6P Modular j ack (For Sensor plug for cabl e) 2X2-M 5X0.
Power supply cable (IZS30-CP) Sensor ca b le (IZS3 0-CS) .
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Sierra Monitor Corporation IZS30 SERIES è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Sierra Monitor Corporation IZS30 SERIES - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Sierra Monitor Corporation IZS30 SERIES imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Sierra Monitor Corporation IZS30 SERIES ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Sierra Monitor Corporation IZS30 SERIES, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Sierra Monitor Corporation IZS30 SERIES.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Sierra Monitor Corporation IZS30 SERIES. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Sierra Monitor Corporation IZS30 SERIES insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
