Manuale d’uso / di manutenzione del prodotto TS-III ULTRA del fabbricante Shopsmith
Vai alla pagina of 16
Safety Instructions 2 System Description 3 Preparing your Shopsmith 4 Installing the Ultra Base 6 F ence Assembly 7 Final Calibration 9 Operation 10 Adjustments 13 Maintenance 15 War ranty 15 CONTENTS INCRA TS-III UL TRA O WNER’S MANU AL Please read this manual before use and keep it at hand for easy reference.
2 INCRA Woodworking T ools & Precision Rules SAFETY INSTR UCTIONS Important safety instructions for using the INCRA TS-III Ultra ■ Before using the INCRA TS-III Ultra, read and follow all of the instructions and safety information in this manual.
INCRA TS-III UL TRA Shopsmith Owner ’s Manual 3 SY STEM DESCRIPTION Positioning Control The INCRA TS-III Ultra obtains its great accuracy and repeatability from the precision cast saw- toothed racks which position the fence in exact increments of 1/32”.
4 INCRA Woodworking T ools & Precision Rules T o enjoy the full working range of the INCRA TS-III Ultra , you will want to configure your Shopsmith workstation at shown in Fig. 1 . This configuration requires, (2) 5ʼ Connector T ubes, (2) T elescoping Legs, and (2) Floating T ables.
INCRA TS-III UL TRA Shopsmith Owner ’s Manual 5 3 Add table tab to remaining floating table Mark drill centers on the right edge of the remaining floating table as shown in Fig. 5, then use the (2) #10 x 5/8” self drilling Phillips head fasteners to attach the table tab.
6 INCRA Woodworking T ools & Precision Rules Figur e 9 INST ALLING THE UL TRA B ASE Figur e 10 Figur e 11 Figur e 12 1 Remove endcap from base support panel Remove the (2) fasteners that secure the endcap to one end of the base support panel and remove the endcap.
INCRA TS-III UL TRA Shopsmith Owner ’s Manual 7 1 Slide carriage into Ultra base Slide the carriage into the Ultraʼs base and position the fence mounting bracket above the right edge of the worktable. Pull the carriage clamp up to lock the carriage in place.
8 INCRA Woodworking T ools & Precision Rules 3 Attach fence glides Note: The fence glides included in hardware pack B-08 are configured for the Shopsmith model 520. T o convert the glide for the model 510, see the bottom of this page. Place one of the supplied ¾” x 3” cardboard spacers under each end of the fence as shown in Fig.
INCRA TS-III UL TRA Shopsmith Owner ’s Manual 9 1 Align fence parallel to miter slot and tighten Ultra base mounting screws Unlock the carriage clamp, then slide the fence up to the nearest miter slot and clamp in place. Loosen the (4) Phillips head screws that secure the Ultra base to the base support panel and align the fence to the miter slot.
10 INCRA Woodworking T ools & Precision Rules 3 Set scale position With the Ultra base still locked with the rip fence at the “zeroed” position set in step 2, lift one end of the stainless steel scale from the magnetic track and slide the scale to position 0” under the hairline cursor .
INCRA TS-III UL TRA Shopsmith Owner ’s Manual 11 Figur e 24 Figur e 25 movement easy . Just rotate the tab up. As the rip fence is moved off of the worktable onto the floating table it contacts the table tab and, as movement is continued, the floating table moves with the rip fence.
12 INCRA Woodworking T ools & Precision Rules when cutting grooves to accept inlay strips for a flawless fit, or to loosen up a tight fitting joint. Y ouʼll find it extremely useful when “zeroing” to the fence to the bit or blade or for “centering” the cutter on your work piece when setting up for joinery operations.
INCRA TS-III UL TRA Shopsmith Owner ’s Manual 13 can micro adjust a full 1/4” in either direction. The scale is marked in 1/32” increments. IMPORT ANT : Do not turn the micro adjusting knob with the carriage clamp in the “locked” position.
14 INCRA Woodworking T ools & Precision Rules Realigning the micro adjust range scale If you wish to verify the mid-range location of the microadjust range scale use the following procedure: “Unlock” the carriage clamp and press the micro adjust lever down to place the Ultra base in the micro adjust mode.
INCRA TS-III UL TRA Shopsmith Owner ’s Manual 15 Now locate the carriage so that the Ultra base is centered approximately between the ends of racks #2 and #3. Again, lock the carriage clamp to bridge the two racks and tighten the accessible mounting screw on rack #3.
16 INCRA Woodworking T ools & Precision Rules This page is intentionally blank..
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Shopsmith TS-III ULTRA è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Shopsmith TS-III ULTRA - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Shopsmith TS-III ULTRA imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Shopsmith TS-III ULTRA ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Shopsmith TS-III ULTRA, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Shopsmith TS-III ULTRA.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Shopsmith TS-III ULTRA. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Shopsmith TS-III ULTRA insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
