Manuale d’uso / di manutenzione del prodotto 315.220100 del fabbricante Sears
Vai alla pagina of 86
Operator's Manual CRAFTSMAN + PRO I 0 H A L 10 in. Stationary RADIAL ARM SAW Model No. 315.220100 Save this manual for future reference. CAUTION: Read and follow all Safety Rules and Operating Instructions before first use of this product.
FULL ONE YEAR WARRANTY ON CRAFTSMAN RADIAL ARM SAW If this product fails due to a defect in material or workmanship within one year from the date of purchase, Sears will repair it, free of charge, Contact a Sears Service Center for repair.
Attaching Elevating Handwheel ........................................................................................................................ 23 Installing the Yoke Assembly ....................................................................
The purpose of safety symbols is to attract your attention to possible dangers, The safety symbols, and the explanations with them, deserve your careful attention and understanding.
• USE THE PROPER EXTENSION CORD. Make sure your extension cord is in good condition. Use only a cord heavy enough to carry the current your product will draw, An undersized cord will cause a drop in line voltage resulting in loss of power and overheating, A wire gage size (A.
• CUT ONLY WOOD, PLASTIC OR WOOD-LIKE MATERIALS. Do not cut metal, • BEFORE MAKING A CUT, be sure all adjustments are secure. • NEVER cut more than one piece at a time, DO NOT STACK more than one workpiece on the saw table at a time, • DO NOT REMOVE THE SAW'S BLADE GUARD.
• SECURE THE SAW. Firmly bolt the saw to the leg stand to keep the saw from tipping, walking, or sliding, • DO NOT SET UP WORK WITH THE BLADE SPINNING. Keep the saw power off until you are ready to use it. • RIP ONLY WORKPIECES LONGER THAN THE BLADE'S DIAMETER.
EXTENSION CORDS Use only 3-wire extension cords that have 3-prong grounding plugs and 3-pole receptacles that accept the tool's plug, When using a power tool at a consid- erable distance from the.
CHANGING VOLTAGE See Figures 2- 4. Your radial saw has been set up at the factory to operate efficiently on a 120V AC single voltage circuit, However, if heavy duty operation is required, the circuits.
Blade Arbor Blade Diameter Blade Bevel Angle Radial Arm Swing Range Blade Height Adjust Carriage Travel Cutting Capacity - Maximum Cross Cut Cutting Capacity - Maximum Out-Rip 5/8 in. lOin. 0 o _ 90 ° 45 ° minimum left - 90 ° right 5.35 in. 17.25 in.
Resin A sticky, sap-based substance. RipCut Ina radial saw, a cut made with the blade parallel to the fence andperpendicular to the arm (can be across or with the grain), The teeth point up at the point of contact withthewood.
Check all loose parts from the box with the list below, Use the instructions on the following pages to assemble. All fasteners are shown actual size, 1, Saw Assembly .................................................... 1 SAW ASSEMBLY SHOWN AS PACKED 2, Elevating Handwheel 3, A, Handwheel .
Check aH bose parts from the box with the Hst bebw. Use the instructions on the following pages to assembb. AH fasteners are shown actual size. . Saw Base to Leg Stand AssemMy A. Saw AssemMy (not shown) ........................... 1 B, Leg Stand AssemMy (not shown) .
Check aH Uoose parts from the box with the Hst beUow. Use the instructions on the following pages to assemMe. AH fasteners are shown actuaU size, 12. TaMe Support A. TaMe Support Rails ....................................... 2 B. Square Head BoUt (5/18-18 x 3/4 in.
The following tools are needed for assembly and alignment. They are not included with this saw. LEVEL HEX KEYS: 5/32 in. AND 1/8 in, MEDIUM FLAT BLADE SCREWDRIVER PHILLIPS SCREWDRIVER PENCIL PUERS CHA.
] Carriage Lock CONTRO_UT C _R3W_E 10 inch Radial Arm Saw "_ 00 RPM 120 / 240 VOLTS 13 / 6.5 Amp 60 Hz AC 0NLY I N SERVICING, USE ONLY IDENTICAL CRAFTSMAN | LACEMENT PARTS. ! I MODEL 315.220100 BER. NO. _1 I MADE IN TAIWAN / _ _ _ I SEARS, ROEBUCKAND CO.
A WARNING ADVERTENCIA • Read and understand owners manual before operating saw. • For your safety, do not use accessories without proper guarding. • Provide proper workpiece support • Position cutting tool behind the fence.
KNOW YOUR RADIAL SAW See Figure 9A. OVERVIEW - The main operating components include the column, the arm, and the yoke assembly (yoke, motor, and blade), and their operation is summarized in the paragraph below. Safety features and control functions are given also.
FEATURES LiST See Figures 9A - 9D. ADJUSTABLE TABLES - A narrow spacer table and wider rear table that can be repositioned or even replaced with different tables. See Figure 9C. ANTI-KICKBACK PAWLS - Toothed pawls that snag the work in case of kickback during rip cuts.
CARRIAGE - Slides along track under arm and supports yoke. Contained in two carriage covers, one on each side of the arm. See Figure 9C. CARRIAGE LOCK KNOB - Controls whether the carriage is locked or can travel. Located on the left side of the arm on the carriage cover.
MOTOR (13.0/6.5 AMP) - Powers the blade and is controlled by the switch and key at the front of the arm. The powerful induction motor has a capacitor start, it is mounted in the yoke and rotated with the bevel index knob and bevel lock lever. See Figure 9B.
Assembly is best done in the area where the saw will be used. When you remove the saw and hardware from the packing materials, carefully check the items with the Loose Parts list. If you are unsure about the description of any part, refer to their illustrations.
MOUNTING SAW TO LEG STAND See Figure ! 1. _ WARNING: Firmly bolt the saw to the leg stand to keep the saw from tipping, walking, or sliding. [] Locate the following hardware from a small hard- ware bag: 4 hex bolts (5/16-18 x 5/8 in.) 4 Iockwashers (5t16 in.
INSTALUNG THE YOKE ASSEMBLY See Figures 13A- 13C. The yoke rides in the carriage below the arm and supports the motor, the blade guard, and the blade. Install the yoke assembly from the front of the arm. [] Remove the carriage stop screw and lockwasher from below the front of the arm with a 1/4 in.
REMOVING THE BLADE See Figure 14. Remove the blade and blade guard assembly during setup for safety and better access. The blade guard includes an upper blade guard, an outer lower guard, and an inner lower guard. The lower inner guard consists of two overlapping slotted metal strips.
SETTING THE ARM LOCK KNOB See Figure 16. it may be possible to move the arm when locked, if the arm lock knob is too loose. If the arm does not move freely when unlocked, the arm lock knob may be too tight. Use this procedure to check and set the arm lock knob by turning the arm lock wheel (under the carriage arm).
SETTING THE BEVEL LOCK LEVER See Figures 18A- 18C. The bevel lock lever locks the blade at desired angles other than the preset positive stop angles. The bevel lock lever is preset at the factory but may need readjustment after shipping or extended use.
TiGHTENiNG THE ARM AND COLUMN See Figure 19. There should be no play, vertical or horizontal, in the arm relative to the column. If you can move the arm up, down or sideways when the arm lock is unlocked, use the following steps to tighten the arm.
[] Rotation Check: To check the rotation, hold the front of the arm with one hand and grasp the top of the column support with the other. Press the arm to the side. if there is play between the column support and the column tube, it needs to be ad= justed.
ADJUSTING THE CARRIAGE BEARINGS See Figures 21A - 21B. Loose carriage bearings permit the blade to wander slightly while cutting, which will result in a poor cut and more wear and tear on the saw. Use the following steps to check for tightness and to then adjust the bearings if needed.
LEVEUNG THE TABLE SUPPORTS See Figures 22A - 22B. The table supports must be perfectly level. [] Pull the bevel lock lever forward to unlock it. Use the bevel index knob to rotate the motor so the arbor shaft points down. Lock the bevel lock lever. [] Release the arm lock knob to angle the arm.
iNSTALLiNG THE FRONT TABLE See Figures 23A - 23C. Use this procedure to install the fixed front table. The top of the table has counterbored holes, predrifled from the top, around the center to attach the table, in the center are a counterbored hole and a small hole, which is not counterbored.
LEVELING THE FRONT TABLE See Figure 24. If there are any high or low areas on the front table, they should be removed by adjusting the leveling screws in the center holes on the front table. [] Place the rear table on its edge across the front table to check for gaps.
THUMBSCREW CLAMP BRACKET SQUARENUT 1 CUP WASHER RECTANGLE HOLE CUP TO WASHER LOOSEN TO TIGHTEN CLAMPSHOWN ASSEMBLED SLOT Fig. 25B TABLE SUPPORT _NSTALUNG BLADE AND BLADE GUARD See Figures 26A - 26C. [] Collect the blade and hardware that were removed earlier.
[] Orient inner slotted metal strip so thatit is located to the leftof outer slotted metal strip. [] Toprevent binding, align flats of retaining screw nut in slots of inner slotted metal strip. [] insert retaining screw through outer slotted metal strip andthread intoretaining screw nut.
_NSTALLING RiP SCALE _ND_CATORS See Figure 28. The rip scale indicators on the arm show the distance between the blade and the rip fence with the fence in the front and rear positions. The upper scale is used when the fence is positioned directly behind the front table.
ALIGNING THE ARM FOR CROSS CUTS See Figures 29,4 - 29C. This procedure checks whether the arm is exactly 0 ° for cross cut travel by checking the blade against the table and the miter indicator. Remove the rear table, spacer table, and fence, but leave the front table in place.
ALIGNING BLADE TO TABLE AT 0 ° BEVEL See Figures 30A - 30D, This procedure squares the blade to the table at 0 ° bevel (vertical) so the blade angle will be accurate. If the blade is not at 0 ° bevel, follow the steps below to rotate slightly, You will need a framing square and a 1/4 in, hex key, • Position the blade in front of the fence.
SQUARING BLADE TO FENCE See Figures 31A - 31C. This procedure squares the miter angle of the blade to the fence to reduce the risk of binding and kickback. If the blade is not square to the fence, the yoke assem- bly must be rotated slightly. Have a framing square, a 1/2 in.
PARALLELING BLADE TO TABLE See Figures 32A - 32C. This procedure squares the blade to the table at 90 ° bevel so horizontal cuts will be accurate. This also reduces kickback, as well as splintering and burning of the cut edges of the workpiece. If the blade is not at 90 ° bevel, follow the steps to rotate the blade unit slightly.
ALIGNING THE RIP SCALE INDICATORS See Figures 33A - 33B. The rip scale indicators on the arm show the distance between the blade and the rip fence. The upper scale is used when the fence is positioned directly behind the front table, The lower scale is used when the fence is at the extreme rear, directly in front of the column.
INSTALLING CONTROL CUT DEVICE See Figure 34, Note: Before installing the control cut device, the yoke assembly will travel back and forward on the carriage by pulling the handle, After installing the .
CHECK ALIGNMENT OF ARM AND BLADE USING LASER See Figure 35. The laser can be used as a quick, accurate routine check for the alignment of your Radial Arm Saw, The saw should be aligned according to th.
BASIC OPERATION OF THE RADIAL ARM SAW A radial arm saw can be used for straight-line cutting operations such as cross cutting, ripping, mitering, beveling, compound cutting, and resawing.
SWITCH AND SWITCH KEY See Figures 37 - 39. The main power switch has been placed on the front of the arm for easy access. The yellow switch key prevents accidental starting of the main power switch when saw is not being used. To activate the switch, insert the switch key and lift switch to ON position.
CUTTING AIDS See Figures 40 - 42. Cutting aids are used to improve the setup and help make the operator's work safer and more accurate. They can be made from scrap wood and in various sizes and shapes for specific projects. The basic types are pushsticks, pushblocks, and featherboards.
MAKING A CROSS CUT See Figure 43. Use this procedure to make a cut with the blade vertical and straight forward, If a kerf does not exist for the line of the cut (cutting path), follow the steps to ma.
MAKING A MITER CUT See Figure 44. In a miter cut, the blade is vertical and the arm angled, If a kerf does not exist for the cutting path, make one (instructions below). Each cutting path requires its own kerf, ,_ WARNING: Make sure the blade guard is lowered and is working properly to prevent possible injury.
MAKING A BEVEL CUT See Figure 45. This procedure makes a cut with the blade and motor angled and the arm straight (90 ° to fence), If there is no kerf, follow the steps to make one, Try this cut on s.
MAKING A COMPOUND CROSS CUT See Figure 46. In this cut, both the blade and the arm are angled, Be familiar with both bevel and miter cuts before making a compound cut, Practice on scrap wood, ,_ WARNI.
RIP CUT HAZARDS AND PRECAUTIONS Two hazards are specifically associated with rip cutting: outfeed zone and wrong way feed, In the outfeed zone (behind the blade), the blade teeth point down. The slightest contact while the blade is still spinning can snag clothing, jewelry, the work- piece, or even skin, causing serious personal injury.
• Put the blade in the in-rip position between the motor and the column. Release the yoke lock handle and pivot the yoke to the left, with the yoke pivot latch on the right side of the arm, (Use the out-rip position only for rips 12 in. or more in width; pivot the yoke to the right so the motor is between the blade and column.
MAKING OTHER CUTS See Figures 49 - 50. Variations from the basic cuts include cutting long workpieces and non-through cuts. When making one of the following cuts, follow the instructions that apply for the basic cut, depending on the position, shape, and size of the wood.
NON-THROUGH CUTS See Figure 50. ,_, WARNING: Unplug the saw while removing or replacing the blade guard, Turn on the saw with the switch on the arm to confirm the blade is not receiving power. • Remove the blade and blade guard (see Assembly section), • Place a support the same height as the saw table nearby for the cut work.
MOUNTING THE LASER GUIDE See Figure 51. • Unplug your saw, ,_, WARNING: Failure to unplug your saw could result in accidental starting causing possible serious personal injury, • Remove the blade .
CHANGING THE BATTERIES See Figure 53. • Unplug your saw. ,_ WARNING: Failure to unplug your saw could result in accidental starting causing possible serious personal injury, Remove the laser guide from the saw. Lay laser guide on a flat surface with the two phillips screws facing upward.
GENERAL MAINTENANCE ,_ WARNING: When servicing, use only identical Craftsman replacement parts. Use of any other part may create a hazard or cause product damage.
CAUSE SOLUTION Saw does not start. 1. Motor cord or controPcut cord is 1. PUug in cord, not pUugged in. 2. Cord or switch is damaged. 2. Have the cord or switch re- pUaced at your nearest Sears Service Center. 3. Circuit fuse is blown. 3. Replace circuit fuse.
PROBLEM CAUSE SOLUTION Saw vibrates excessiveUy. 1. BUade is warped, 1. RepUace the Made, See the removaU procedure in Assembly section, 2. Saw is not mounted secureUy. 2. Tighten aH hardware, 3. Work surface is uneven, 3. Reposifion on a fiat surface, Adjust the bveHng feet on bgs.
CAUSE SOLUTION HandwheeU is hard to turn or 1_ Sawdust has collected on the 1_ Remove handwheeU; clean and column binds, elevating shafL Uubricate the shafL 2_ Column is out of aHgnmenL 2_ See Adjusting the Column Tube in Assembly section, Saw burns or scores edges of 1_ Column tube is too Uoose in the 1_ See Adjusting the Column wood in cut.
PROBLEM CAUSE SOLUTION Miter or cross cuts are not true. 1. Scab pointer is not correct. 1. Reset the pointer at the top rear of arm. 2. Column is out of alignment. 2. See Adjusting the Column Tube in Assembly section. 3. Carriage is misaligned. 3. See Setting the Arm Lock HZheel in the Assembly section.
PROBLEM CAUSE SOLUTION Saw Made tends to push wood to 1, BUade is heeling, 1, See Squaring the Blade to the one side when cross cutting, Fence in Adjustments section, 2, CoUumn tube is Uoose in coUumn.
G3 CRRFTSMnN RADIAL SAW 315.220100.
CRAFTSMAN RADIAL ARM SAW- MODEL NO. 315.220100 The model number will be found on a plate attached to the base. Always mention the model number in all correspondence regarding your RADIAL ] ARM SAW or when ordering repair parts.
CRAFTSMAN RADIAL ARM SAW- MODEL NO. 315.220100 I The model number will be found on a plate attached to the base. Always mention the model number in all correspondence regarding your RADIAL ! ARM SAW or when ordering repair parts.
CRAFTSMAN RADIAL ARM SAW- MODEL NO. 315.220100 • I The model number will be found on a plate attached to the base. Always mention the model number I in all correspondence regarding your RADIAL ARM SAW or when ordering repair parts, J 19 18 _ 17 SEE FIGURE [ 14 24 _f_.
CRAFTSMAN RADIAL ARM SAW- MODEL NO. 315.220100 • I The model number will be found on a plate attached to the base, Always mention the model number in all correspondence regarding your RADIAL ARM SAW or when ordering repair parts, I PARTS LIST FOR FIGURE B KEY PART NO.
CRAFTSMAN RADIAL ARM SAW- MODEL NO. 315.220100 I The model number will be found on a plate attached to the base. Always mention the model number in all correspondence regarding your RADIAL ! ARM SAW or when ordering repair parts.
CRAFTSMAN RADIAL ARM SAW- MODEL NO. 315.220100 I he model number will be found on a plate attached to the base. Always mention the model number in all correspondence regarding your RADIAL ! ARM SAW or when ordering repair parts. J PARTS LIST FOR FIGURE C KEY PART NO.
CRAFTSMAN RADIAL ARM SAW- MODEL NO. 315.220100 • I The model number will be found on a plate attached to the base, Always mention the model number I in all correspondence regarding your RADIAL ARM SAW or when ordering repair parts, J 14 15 22 21 19 23 FIGURE D rRRI:TSMRN + TABLE SAW 315.
CRAFTSMAN RADIAL ARM SAW- MODEL NO. 315.220100 • I The model number will be found on a plate attached to the base, Always mention the model number in all correspondence regarding your RADIAL ARM SAW or when ordering repair parts, I PARTS LIST FOR FIGURE D KEY PART NO.
CRAFTSMAN RADIAL ARM SAW- MODEL NO. 315.220100 • I The model number will be found on a plate attached to the base, Always mention the model number I in all correspondence regarding your RADIAL ARM SAW or when ordering repair parts, I 12 14 15 21 22 23 16 19 20 18 24 26 27 1 FIGURE E £RRFTSMRN ° TABLE SAW 315.
CRAFTSMAN RADIAL ARM SAW- MODEL NO. 315.220100 • I The model number will be found on a plate attached to the base, Always mention the model number in all correspondence regarding your RADIAL ARM SAW or when ordering repair parts, I PARTS LIST FOR FIGURE E KEY PART NO.
CRAFTSMAN RADIAL ARM SAW- MODEL NO. 315.220100 • I The model number will be found on a plate attached to the base, Always mention the model number I in all correspondence regarding your RADIAL ARM SAW or when ordering repair parts, J 18 3O 3 22 31 FIGURE F rRRFTSMRN + TABLE SAW 315.
CRAFTSMAN RADIAL ARM SAW- MODEL NO. 315.220100 • I The model number will be found on a plate attached to the base, Always mention the model number I in all correspondence regarding your RADIAL ARM SAW or when ordering repair parts, I PARTS LIST FOR FIGURE F KEY PART NO.
CRAFTSMAN RADIAL ARM SAW- MODEL NO. 315.220100 • I The model number will be found on a plate attached to the base, Always mention the model number I in all correspondence regarding your RADIAL ARM S.
CRAFTSMAN RADIAL ARM SAW- MODEL NO. 315.220100 • I The model number will be found on a plate attached to the base, Always mention the model number in all correspondence regarding your RADIAL ARM SAW or when ordering repair parts, I PARTS LIST FOR FIGURE G KEY PART NO.
CRAFTSMAN RADIAL ARM SAW- MODEL NO. 315.220100 I he model number will be found on a plate attached to the base. Always mention the model number in all correspondence regarding your RADIAL ! ARM SAW or when ordering repair parts.
CRAFTSMAN RADIAL ARM SAW- MODEL NO. 315.220100 I he model number will be found on a plate attached to the base. Always mention the model number in all correspondence regarding your RADIAL ! ARM SAW or when ordering repair parts. J PARTS LIST FOR FIGURE H KEY PART NO.
CRAFTSMAN RADIAL ARM SAW- MODEL NO. 315.220100 The model number will be found on a plate attached to the base. Always mention the model number in all correspondence regarding your RADIAL ! ARM SAW or when ordering repair parts.
CRAFTSMAN RADIAL ARM SAW- MODEL NO. 315.220100 I The model number will be found on a plate attached to the base. Always mention the model number in all correspondence regarding your RADIAL ! ARM SAW or when ordering repair parts. J PARTS LIST FOR FIGURE I KEY PART NO.
CRAFTSMAN RADIAL ARM SAW- MODEL NO. 315.220100 I he model number will be found on a plate attached to the base. Always mention the model number in all correspondence regarding your RADIAL ! ARM SAW or when ordering repair parts. J 2 SEE FIGURE K 7 8 .
CRAFTSMAN RADIAL ARM SAW- MODEL NO. 315.220100 I he model number will be found on a plate attached to the base. Always mention the model number in all correspondence regarding your RADIAL ! ARM SAW or when ordering repair parts. J PARTS LIST FOR FIGURE J KEY PART NO.
CRAFTSMAN RADIAL ARM SAW- MODEL NO. 315.220100 I he model number will be found on a plate attached to the base. Always mention the model number in all correspondence regarding your RADIAL ! ARM SAW or when ordering repair parts.
CRAFTSMAN RADIAL ARM SAW- MODEL NO. 315.220100 I he model number will be found on a plate attached to the base. Always mention the model number in all correspondence regarding your RADIAL ! ARM SAW or when ordering repair parts. J PARTS LIST FOR FIGURE K KEY PART NO.
For repair of major brand appliances in your own home... no matter who made it no matter who sold it! 1-800-4°MYoHOM E sM Anybme. day or n,ght (1-800-469-4663) www.sears.com To bring in products such as vacuums lawn equipment and electronics for repair, call for the location of your nearest Sears Parts & Repair Center.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Sears 315.220100 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Sears 315.220100 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Sears 315.220100 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Sears 315.220100 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Sears 315.220100, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Sears 315.220100.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Sears 315.220100. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Sears 315.220100 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
