Manuale d’uso / di manutenzione del prodotto 200.71226 del fabbricante Sears
Vai alla pagina of 16
OWNER'S MANUAL Microprocessor Controlled, Fully Automatic Operation Battery Charger with Engine Starter Plus Battery and Alternator Tester 2=AIVlP SLOW CHARGE 15=AMP FAST CHARGE 40-AMP RAPID CHARGE 125=AMP ENGINE START FOR 12=VOLT BATTERIES Model No.
WARRANTY ................................................................................................................ 2 IMPORTANT SAFETY INSTRUCTIONS ................................................................... 3 PERSONAL SAFETY PRECAUTIONS .
WARNING = RISK OF EXPLOSIVE GASES WORKING IN VICINITY OF A LEAD-ACID BATTERY IS DANGEROUS. BAT- TERIES GENERATE EXPLOSIVE GASES DURING NORMAL BATTERY OPERATION. FOR THIS REASON, IT IS OF UTMOST IMPORTANCE THAT EACH TIME BEFORE USING YOUR CHARGER, YOU READ THIS MANUAL AND FOLLOW THE INSTRUCTIONS EXACTLY.
Never place charger directly above battery being charged. The gases from the battery wilt corrode and damage the charger. Never touch the battery clamps together when the charger is on. You could cause a spark. Never operate charger ifit has received a hard blow, been dropped, or otherwise damaged.
PLUGGING IT IN Your charger requires a 120V AC 2-prong wall outlet receptacle installed according toalllocal codes and ordinances. It is important tounderstand your charger's requirements. This section will tell you about your charger's electrical requirements and how to prepare a battery forcharging.
NOTE: A marine (boat) boat battery must be removed and charged on shore. To charge it on board requires equipment specially designed formarine use. IMPORTANT: Follow all safety instructions and precautions when charging your bat- tery. Wear complete eye protection and clothing protection.
CHARGING BATTERY REMOVED FROM THE VEHICLE: POSITIVE NEGATIVE BATTERY BATTERY _CHARGER POWER 24", 6 GAUGE CABLE GROUNDED POWER OUTLET 1. Note the polarity of the battery posts by checking the identification marks on the battery: POSITIVE (POS, P or +) and NEGATIVE (NEG, N or-).
in seconds. It starts at 5 and counts down to 0. 3. Cool Down - After cranking, the char- ger enters a mandatory 3-minute (180 second) cool down state. During this period, no settings can be changed. The buttons are ignored. The digital display indicates the remaining cool down time in seconds.
If the charge mode is changed after charg- ing has started (by pressing the CHARGE RATE or CHARGE TYPE button), the charging process wilt berestarted. The voltage displayed during charging is the charging voltage and usually will be higher than the battery's resting voltage.
71226 CONTROL PANEL GUIDE MODE OF OPERATION Initial power-up, battery not detected No battery or reversed battery detected Battery tester activated Battery tester with charged battery Battery tester w.
OVERVIEW This battery charger has a built-in battery tester that displays either an accurate battery voltage or an estimate of the battery's relative charge based on the battery voltage and the Battery Council International scale. TESTING SEQUENCE There are four basic steps required to use the 71226 as a battery tester.
This battery charger has a built-in alter- nator tester that displays either an accu- rate alternator voltage or an estimate of the alternator's relative output compared tonormal alternators. The Alternator % values displayed should be taken as general reference, not precise diagnosis.
This charger adjusts the charging time in order to charge the battery completely, efficiently and safely. The microproces- sor automatically makes the necessary decisions. However, this section includes guidelines that can be used to estimate charging times.
Read this entire manual before using your charger. The tips below serve only as a guide for specific situations. If your vehicle won't start: You don't need to fully charge a battery to start your vehicle.
Performance problems often can be corrected by the user. Please read through this chart for a possible solution to common problems. PROBLEM POSSIBLE CAUSE SOLUTION The battery is connected The charger is in tester and the charger is on, mode, not charger mode.
This section shows an illustration of your battery charger. Use it to become familiar with part locations and appearance. Replacement Parts List Sears 71226 iTEM DESCRIPTION PART NUMBER 1 Handle Assem.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Sears 200.71226 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Sears 200.71226 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Sears 200.71226 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Sears 200.71226 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Sears 200.71226, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Sears 200.71226.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Sears 200.71226. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Sears 200.71226 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
