Manuale d’uso / di manutenzione del prodotto 113.244501 del fabbricante Sears
Vai alla pagina of 24
i/Save This Manual _'_'' For Future Reference MODEL NO, 113,244501 10-INCH BAND SAW Se;iot ..... Number Model and serial numbers may be found on the back of the saw You should record bo.
FULL ONE YEAR WARRANT ON CRAFrSMA. BENCHTOP TOOLS If this Band Saw fails due to a defect in material or workmanship, within one years from the ' date of purchase, RETURN IT TO THE NEAREST SEARS SERVICE CENTER IN THE UNITED STATES, and Sears will repair it, free of charge.
If any part is missing, bent, or broken in any way, or any electrical part doesn't work properly, turn the saw off and unplug the saw REPLACE damaged, miss- ing, or failed parts before using the .
Plan the way you will hold the workpiece from start to finish, Do not hand hold pieces so small that your fingers will go under the blade guard Use jigs or fixtures to hold the work and keep your hand.
motor specifications and eRectrBcan requBrements This machine is designed to use, and is equipped with, a 1725 RPM motor It is wired for operation on 120 volts, 60 Hz., alternating current (TOOL MUST NOT BE CONVERTED TO OPERATE ON 230 VOLT).. For replacement motor refer to parts list in this manual.
contents POWER TOOL WARRANTY ..................................... 2 SAFETY INSTRUCTIONS FOR BAND SAW .............. 2 GLOSSARY OF TERMS FOR WOODWORKING .... 4 MOTOR SPECIFICATIONS AND ELECTRICAL REQUIREMENTS ............ .............................
C ITEM = A B C D TABLE OF LOOSE PARTS QTY. Basic saw assembly ............................ 1 Owners Manual ..................................... 1 Saw Table ........................................... t Loose Parts Bag Containing the following parts: Key Switch .
assembOy An alternate method of mounting is to fasten band saw to a mounting board The board should be of suf- ficient size to avoid tipping el saw while in use Any good grade of plywood or chipboard .
INSTALLING THE BLADE I ARNING:Turn off saw, remove switch key and unplug saw before removing or installing blade° I Loosen the upper slide lock knob and position the guide assembly about half way bet.
7 The upper wheel needs to be placed in its lowest position Locate the tension lock knob on the back of the saw and turn it counterclockwise approximately two turns Lift the tension catch away from the teeth and move it to its lowest position Tension Catch CAUTION: To avoid being scraped, if the blade should suddenly uncoil, wear safety goggles.
WARNING: Turn off saw, remove switch key | ] and unplug before making any adjustments° J TRACKING THE BLADE Blade tension must be properly adjusted before tracking the blade.
NOTE: Letting the blade teeth hit the blade guides while using the band saw will ruin the blade° The set of the teeth and the sharpened edge of the teeth would be damaged Proper adjustment of the upp.
7 Locate the bevel indicator and 10-32 x 3/8"long panhead screw in loose parts bag, 8 Usea #2 phillips screwdriver to attach the bevel indicator to the back of the frame, in the small recess belo.
getting to know your band saw Cover Frame 9 Wrench Holder Tension Catch . Table 2 Upper Slide Lock Knob Tracking Adjustment Set Screw 7 Sawdust Hose Clip Ejection Port 10 On-Off Switch 8 Cover Hinges 1 Blade Guides 5 Tension Lock Knob 4 Beve Scale Bevel indicator NOTE: Cover shown open for clarity 3 Table Lock Knob .
9 Wrench Holder Keeps 1/8"Hex 'L" Wrench conveniently located forblade guide adjustments 10 ON-OFF SWITCH. The On-Off Switch hasa lock- ing feature THIS FEATURE IS INTENDED TO HELP PREV.
Basic Saw Operations BEFORE EACH USE: Inspect your saw. DISCONNECT THE SAW To avoid injury from acci- dental starting, unplug the saw, turn the switch off and remove the switch key before changing the setup, opening covers, removing guards, or blade CHECK FOR DAMAGED PARTS.
• Noise levels vary widely To avoid possible hear- ing damage, wear ear plugs or muffs when using your saw tot hours at a time • For dusty operations, wear a dust mask along with the safety goggle.
basic band saw operation A band saw is basically a "curve cutting" machine It is also used for straight-line cutting operations such as cross cutting, ripping, mitering, beveling, com- pound.
maintenance WARNING: For your own safety, turn switch "OFF", remove switch key and remove plug from power outlet before maintaining or lubricating your band saw.
troubleshooting WARNING: For your own safety, turn switch "OFF", remove switch key and remove plug from power outlet before readjusting or aligning your band saw. TROUBLE REMEDY Motor will not run. 1 Blade does not run in the approximate center of the upper wheel.
repair parts FOR 10-INCH BAND SAW 113.244501 Always order by Part Number - Not by Key Number 2 4 4 6 5 NO 1 2 3 4 5 6 7 FIGURE 1 Part No. 820286 ST D601103 817899 STD502502 820279 820281 820284 Description i,in,,ll,,= Guard Blade .
to 40 32 31 :E FIGURE 2 18 48 FIGURE 3 FOR 10-INCH BAND SAW 113.244501 Always order by Part Number- Not by Key Number 23 45 22 _,..1 23 ., 6 7 . _ _ 10 "_l 24 6 "_" 11 SEE FIGURE 1 46 SEE FIGURE 1 _ 7 _ 12 6 15 14 10 6 11 13 .
Key No 1 3 4 5 6 7 8 9 10 11 12 !3 14 15 16 17 18 19 20 21 22 23 24 25 FOR IO-INCH BAND SAW 113.244501 Always order by Part Number- Not by Key Number FIGURE 3 Part 820288 STD541031 STD551131 820269 81.
MODEL NO. The model number of your 10-Inch Band Saw will be found on a plate located on the back of the Band Saw below the motor. When requesting service or ordedng parts, always provide the following.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Sears 113.244501 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Sears 113.244501 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Sears 113.244501 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Sears 113.244501 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Sears 113.244501, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Sears 113.244501.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Sears 113.244501. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Sears 113.244501 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
