Manuale d’uso / di manutenzione del prodotto 113.2076 del fabbricante Sears
Vai alla pagina of 24
Save this Manual for Future Reference Sears ! MODEL NO, 113.207600 SAW ONLY MODEL NO. 113.207650 SAW WITH LEGS Serial Number Model and serial number may be found at the right-hand side of the base You.
FULL ONE YEAR WARRANTY ON CRAFTSMAN SCROLL SAW If within one year from the date of purchase, this Craftsman Scroll Saw fails due to a defect in material or workmanship, Sears will repair it, free of c.
additional safety instructions for scroln saw Safety is a combination of operator common sense and alertness at all times when the scroll saw is being used WARNING: FOR YOUR OWN SAFETY, DO NOT ATTEMPT TO OPERATE YOUR SCROLL SAW UNTIL IS IS COMPLETELY ASSEMBLED AND INSTALLED ACCORDING TO THE INSTRUC- TIONS o .
location and function of controls TENSION KNOB ON/OFF SWITCH GUARD LOCK KNOBS BLADE HOLDER RETAINING CLIPS GUARD BLOWER TUBE ]OLDERS BLADE HOLDER POCKETS BEVEL SCALES BEVEL LOCK KNOB TABLE I INSERT MI.
contents POWER TOOL WARRANTY ................... 2 GENERAL SAFETY INSTRUCTIONS FOR POWER TOOLS ........................... 2 ADDITIONAL SAFETY INSTRUCTIONS FOR SCROLL SAW .............................. 3 MOTOR SPECIFICATIONS AND ELECTRICAL REQUIREMENTS .
Item Description Qty, 1 Screw, Serrated Truss Hd. 114-20 x 5/8. 24 2 Le .............................. 4 3 Stilfener, Side ........... :i,:i,ii: 2 4 *Lockwasher, Ext 114 .................... 24 5 *Nut, Hex 1t4-20 ........................ 24 6 Stiffener, End .
MOUNTING SCROLL SAW ON LEG SET 1 Place the Scroll Saw on the Steel Legs, position as shown by aligning the mounting holes in the base of the Scroll Saw with those in the END STIFFENERS (marked with an.
assembly MOUNTING SCROLL SAW TO MOUNTING BOARD An alternate method of mounting is to fasten Scroll Saw to a mounting board The board should be of sufficient size to avoid tipping of saw while in use. Any good grade of plywood or chipboard with a 3/4" minimum thickness is recommended.
BLADE DNSTALLATUON AND TENSIONnNG FOR PLAnN-END OF{ PRN TYPE BLADES NOTE: Included with the scroll saw are three 5" blades. This saw can accommodate 5" to 6" plain- end blades, and 5" pin type blades.
assembly 7 Locate table insert among loose parts and install in table by sliding the insert in place from back to front of blade, aligning rear tab on back of insert, and pushing downward on front of .
TO INSTALL/TENSION PIN TYPE BLADES: WARNING: FOR YOUR OWN SAFETY, TURN SWITCH ='OFF", REMOVE KEY AND REMOVE PLUG FROM POWER SOURCE OUTLET BEFORE REMOVING OR INSTALLING SAWBLADE, t Locate two.
assembly 3. For plain-end blades, remove blade holders (with blade installed) from retainer clips by putling clips away from blade holders. Pull out upper and Iowe_ blade holders Ptace blade ho(der&ap.
ADJUSTING THE BLADE SQUARE TO TABLE WARNING: FOR YOUR OWN SAFETY, TURN SWITCH "OFF", REMOVE KEY AND REMOVE PLUG FROM POWER SOURCE OUTLET. 1, WITH BLADE INSTALLED AND TENSIONED place combinat.
assembly INSTALLATION OF BEVEL SCALES 1 With blade installed and tensioned, Iocatetwo (2) bevel scales among loose parts 2 Locate slit in paper backing on back side of scale.
getting to know your scrota saw 13 ON/OFF SWITCH I TENSION KNOB 2 GUARD LOCK KNOBS 3 GUARD 5 BLADE HOLDER 4 RETAINING CLIP BLOWER 6 TUBE BLADE HOLDERS 7 BLADE HOLDER POCKETS 12 BEVEL SCALES 11 BEVEL LOCK KNOB 10 BLADE STORAGE , T TABLE INSERT 8 MITER LOCK KNOB 1.
2 To turn machine on, place finger under switch lever and pull end of switch out 3. To turn machine OFF... PUSH lever in. NEVER LEAVE THE MACHINE UNATTENDED UNTIL IT HAS COME TO A COMPLETE STOP, PUSH 4 To lock switch in OFF position .. hold switch IN with one hand.
basic scronH saw operation NOTE: Make certain set screws in blade holders are tight prior to each use of the scroll saw WARNING: NEVER OPERATE WITHOUT TABLE INSERT IN PLACE° This scroll saw accepts a.
basic scroll saw operation USE OF MITER GAUGE - CROSS CUTTING WARNING: TO AVOID WORK INSTABILITY OR RUNNING THE MITER GAUGE INTO THE BLADE, TURN THE MITER GAUGE FACE TOWARD THE BLADE AND USE THE MITER SLOTACROSSTHE TABLE FRONT FOR ALL ANGLES OVER 55 ° .
MOTOR Frequently vacuum or blow out any sawdust from the motor If the power cord is worn, cut, or damaged in any way, have it replaced immediately LUBRICATION Ali of the BALL BEARINGS are packed with .
PARTS LIST FOR CRAFTSMAN 18-INCH MOTORIZED SCROLL SAW MODEL NO. 113.207600 AND 113.207650 3 63 57 55 56 4O 41 43 66 FIGURE 1 2O.
PARTS LIST FOR CRAFTSMAN 18-INCH MOTORIZED SCROt.L SAW MODEL NO. 113.207600 AND 113.207650 Always order by Part Number - Not by Key Number FIGURE 1 %_oy Part No.
PARTS LIST FOR CRAFTSMAN 18-INCH MOTORIZED SCROLL SAW MODEL NO. 113.207600 AND 113,207650 8 FIGURE 2 - MITER GAUGE ASSEMBLY Ke y Pa r t No. No. Description H, ii 1 2 3 4 5 6 7 8 62170 62176 STD551010 .
PARTS LIST FOR CRAFTSMAN 18-INCH MOTORIZED SCROLL SAW MODEL NO. 113.207600 AND 113.207650 4 5 3 | 2 '_o 6 o 6 5 4 _tj 2 ] 2 FIGURE 3 - LEG SET FOR MODEL 113.207650 ONLY ,,,J,l,,. Key Part No. No. 1 60314 2 3 4 5 6 7 8 63749 62554 STD551225 STD541025 62615 STD541250 803835 66037 Description .
SERVICE MODEL NO 113.207600 SAW ONLY MODEL NO. 113.207650 SAW WITH LEGS HOW TO ORDER REPAIR PARTS 18-iNCH MOTORIZED SCROLL SAW Now that you have purchased your 18-inch motorized Scrolf Saw should a ne.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Sears 113.2076 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Sears 113.2076 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Sears 113.2076 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Sears 113.2076 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Sears 113.2076, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Sears 113.2076.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Sears 113.2076. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Sears 113.2076 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
